Engineering topics

Kane, T. J.

Publications and source records attributed to Kane, T. J..

11 records

NASA NTRS2000

Ion Layer Separation and Equilibrium Zonal Winds in Midlatitude Sporadic E

In-situ observations of a moderately strong mid-latitude sporadic-E layer show a separation in altitude between distinct sublayers composed of Fe(+), Mg(+), and NO(+). From these observations it is possible to estimate the zonal wind field consistent with diffusive equilibrium near the altitude of the layer. The amplitude of the zonal wind necessary to sustain the layer against diffusive effects is less than 10 meters per second, and the vertical wavelength is less than 10 km.

Earle, G. D.↗

NASA NTRS1991

Injection chaining of diode-pumped single-frequency ring lasers for free-space communication

A high-power three-stage laser suitable for use in a space communication system has been built. This laser uses three diode-pumped Nd:YAG oscillators coherently combined using the technique of injection chaining. All three oscillators are in one compact and permanently aligned package, and are actively frequency locked to provide CW single frequency output. The three stages provide the redundancy desirable for space communications.

Cheng, E. A. P.↗

NASA NTRS1987

Monolithic Isolated Single-Mode Ring Laser

MISER uses four-sided ring to lase nonreciprocally. Laser concept provides very-compact, efficient, and stable source of coherent radiation. Lasers of single, very-stable frequency desirable for number of purposes. Frequency stability makes possible coherent detection of laser radiation with low-bandwidth detector, useful for communications. Allows very-high-resolution spectroscopy. Any application where desired to use laser in way microwaves used traditionally enhanced if frequency very stable.

Kane, T. J.↗

NASA NTRS1986

62-dB-gain multiple-pass slab geometry Nd:YAG amplifier

A flash-lamp-pumped slab Nd:YAG laser amplifier with 62 dB of gain is demonstrated. The amplifier remains linear for energy extraction up to 12 mJ, and the beam spatial quality remains good at repetition rates up to 10 Hz. The slab geometry provides for gain averaging in the zigzag dimension, thus eliminating the undesirable effects of nonuniform pumping. This averaging and the necessity for only a single compact gain element are valuable attributes that may allow for eventual laser-diode array pumping of the slab Nd:YAG amplifier.

Kane, T. J.↗

NASA NTRS1985

The slab geometry laser. II - Thermal effects in a finite slab

This paper presents two methods for calculating the thermally induced stress, focusing, and depolarization in a pumped zigzag-slab solid-state laser. A computer program capable of detailed calculations of thermal effects in the general case is described. An approximate analysis of slab thermal effects in many cases allows calculation of these effects without use of the computer model directly. The analysis predicts that slabs of square cross section can be designed to have low depolarization and thermal focusing compared to Nd:YAG laser rods.

Kane, T. J.↗

NASA NTRS1985

Efficient, frequency-stable laser-diode-pumped Nd:YAG laser

One of the main goals of the study was to demonstrate a low-power efficient Nd:YAG laser oscillator for applications in remote coherent Doppler anemometry. An electrical-to-optical slope efficiency of 6.5 percent has been achieved by using commercially available CW laser diodes of up to 100 mW to pump monolithic Nd:YAG rod lasers. The observed Nd:YAG oscillation threshold is at 2.3 mW of laser-diode output power, i.e., a small fraction of the rated output power. The highest Nd:YAG CW output power reached is 4.4 mW at an overall electrical-to-optical efficiency of 1.5 percent. The frequency jitter is less than 10 kHz in 0.3 s.

Zhou, B.↗

NASA NTRS1985

Monolithic, unidirectional single-mode Nd:YAG ring laser

A new solid-state laser has been designed which achieves high single-mode output power by using a unidirectional nonplanar resonator constructed from a single Nd:YAG crystal. When placed in a magnetic field, the laser provides a pump-limited, single-axial-mode output of 163 mW at 1064 nm. The laser has been specifically developed as an oscillator for a long-range coherent Doppler anemometer. Other applications include coherent communications, coherent optical radar, and inertial rotation sensing.

Kane, T. J.↗

NASA NTRS1984

Potential for coherent Doppler wind velocity lidar using neodymium lasers

Existing techniques for the frequency stabilization of Nd:YAG lasers operating at 1.06 micron, and the high-gain amplification of radiation at that wavelength, make possible the construction of a coherent Doppler wind velocity lidar using Nd:YAG. Velocity accuracy and range resolution are better at 1.06 micron than at 10.6 microns at the same level of the SNR. Backscatter from the atmosphere at 1.06 micron is greater than that at 10.6 microns by about 2 orders of magnitude, but the quantum-limited noise is higher by 100 also. Near-field attenuation and turbulent effects are more severe at 1.06 micron. In some configurations and environments, the 1.06-micron wavelength may be the better choice, and there may be technological advantages favoring the use of solid-state lasers in satellite systems.

Kane, T. J.↗

NASA NTRS1984

The slab geometry laser. I - Theory

Slab geometry solid-state lasers offer significant performance improvements over conventional rod-geometry lasers. A detailed theoretical description of the thermal, stress, and beam-propagation characteristics of a slab laser is presented. The analysis includes consideration of the effects of the zig-zag optical path, which eliminates thermal and stress focusing and reduces residual birefringence.

Eggleston, J. M.↗

NASA NTRS1983

Reduced thermal focusing and birefringence in zig-zag slab geometry crystalline lasers

The present investigation is concerned with interferometric measurements of the thermally induced optical effects in laser crystals, taking into account crystals cut in both the zig-zag slab and the conventional rod geometries. The measurements conducted demonstrate the significant advantages obtained by replacing the rod in a Nd:YAG laser with a slab. A description is provided of simple measures designed to eliminate end and edge effects, and efficiency and threshold data for the Nd:YAG slab and the rod it replaced are presented. The only disadvantage is a small increase in cost due to the more difficult fabrication of the slab and the greater amount of Nd:YAG which is needed to allow the ends to be unpumped.

Kane, T. J.↗

NASA NTRS1982

Slab-geometry Nd:glass laser performance studies

It is noted that slab-geometry solid-state lasers potentially provide significant performance improvements relative to conventional rod-geometry lasers. Experimental measurements that use an Nd:glass test-bed slab laser are presented. A comparison is made between the results and computer-model predictions of the slab-geometry approach. The computer model calculates and displays the temperature and stress fields in the slab, and on the basis of these predicts birefringence and index-of-refraction distributions. The effect that these distributions have on optical propagation is determined in a polarization-sensitive ray-tracing section of the model. Calculations are also made of stress-induced surface curvature and the resulting focusing effects. The measurements are found to be in good agreement with the computer-model predictions. It is concluded that the slab configuration offers significant laser-performance advantages in comparison with the traditional rod-laser geometry.

Eggleston, J. M.↗