Search NASA⌕ Search

Engineering topics

Karaman, I.

Publications and source records attributed to Karaman, I..

15 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Orientation dependence of the effect of short-range ordering on the plastic deformation of a medium entropy alloy

Multi-principal-element alloys (also known as medium and high entropy alloys) offer a much larger and richer design space than conventional alloys, providing opportunities for discovering new functionalities and their governing physics. Some of these alloys exhibit an outstanding combination of high strength and ductility, linked to the activation of various deformation modes triggered by low-energy stacking faults. However, a pressing question remains: Is the plasticity of medium- and high-entropy alloys governed only by stacking fault energy, or does atomic short-range order (SRO) play a role? Here, to answer this, we investigated how SRO affects the deformation in single-crystalline NiCoCr, with previous contradictory findings. First, we established unique experimental evidence for SRO formation in bulk single crystals using high-energy synchrotron transmission X-Ray Diffraction. By tuning the degree of SRO by aging at high temperatures, twinning density and strain-induced martensitic phase transformation can be significantly increased in the [110] and [111] orientations under tension, increasing the tensile ductility; yet, no increase was observed along the [001] orientation due to lack of TWinning-Induced Plasticity (TWIP) or TRansformation-Induced Plasticity (TRIP), indicating a strong crystallographic orientation dependence. Our first-principles thermodynamic calculations unequivocally show SRO exists and governs the observed microstructural evolution and deformation hardening behavior. Here we find direct proof that SRO triggers a simultaneous TWIP and TRIP in NiCoCr, a rare microstructural evolution path. Our findings establish that the interplay of SRO and plasticity could be exploited to alter deformation modes and yield unprecedented mechanical response in medium- and high-entropy alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Martensitic Transformation in Fe x Mn 80-x Co 10 Cr 10 High-Entropy Alloy

High-entropy alloys and even medium-entropy alloys are an intriguing class of materials in that structure and property relations can be controlled via alloying and chemical disorder over wide ranges in the composition space. Employing density-functional theory combined with the coherent-potential approximation to average over all chemical configurations, we tune free energies between face-centered-cubic and hexagonal-close-packed phases in Fe x Mn 80 - x Co 10 Cr 10 systems. Within Fe-Mn-based alloys, we show that the martensitic transformation and chemical short-range order directly correlate with the face-centered-cubic and hexagonal-close-packed energy difference and stacking-fault energies, which are in quantitative agreement with recent observation of two phase region (face-centered cubic and hexagonal closed pack) in a polycrystalline high-entropy alloy sample at x = 40 at.%. Our predictions are further confirmed by single-crystal measurements on a x = 40 at.% using transmission-electron microscopy, selective-area diffraction, and electron-backscattered-diffraction mapping. The results herein offer an understanding of transformation-induced or twinning-induced plasticity in this class of high-entropy alloys and a design guide for controlling the physics at the electronic level.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Competing Interactions between Mesoscale Length-Scales, Order-Disorder, and Martensitic Transformation in Ferromagnetic Shape Memory Alloys

In the present study, the effects of composition and heat treatments and the resulting microstructural changes on the martensitic transformation and ferromagnetic transition have been investigated in NiCoMnIn metamagnetic shape memory alloys. In this shape memory alloy system, it is observed that upon heat treatments at a wide temperature range, the onset temperature of the martensitic transformation follows a non-monotonic behavior with respect to heat treatment time, and the nature of the non-monotonic behavior is also a function of composition. This behavior cannot be attributed to well-known factors such as precipitation, change in local composition due to the precipitation and/or global degree of order. In this work, a systematic investigation through synthesis, thermal processing and characterization via thermo-physical measurements, transmission electron microscopy and in-situ synchrotron x-ray diffraction experiments has been used to correlate the non-monotonic dependence of the martensitic transformation and ferromagnetic transition temperatures to the evolution of L2 1 domains arising from a order/disorder phase transition. A thermodynamic model for the magneto-structural transition is combined with classical nucleation theory to further ascertain the role of microstructural length-scales on the onset of the martensitic transformation. This work thus provides understanding of the thermodynamic and kinetic factors that can be controlled to tune the coupled magneto-structural transformations in NiCoMnIn metamagnetic shape memory alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Role of microstructure on the actuation fatigue performance of Ni-Rich NiTiHf high temperature shape memory alloys

Here, the focus of the present study was to systematically investigate the influence of microstructure on the actuation fatigue performance of a Ni-rich NiTiHf high temperature shape memory alloy (HTSMA). Different aging heat treatments led to the formation of H-phase nano-precipitates with different sizes and morphology within the matrix, enhancing thermo-mechanical stability and enabling control of transformation temperatures. The actuation fatigue testing of specimens was performed until failure through thermally-induced reversible martensitic transformation under a constant stress (300 MPa) with two distinct upper cycle temperatures (UCT) of 300 °C and 350 °C. Consequently, the specimens heated to 700 °C and furnace cooled to 100 °C in 48 h, with relatively large precipitates, failed at average fatigue life of 15,500 cycles and exhibited 1.0% average actuation strain in the 300 °C UCT experiments, while those aged at 550 °C for 3 h, with the precipitate sizes less than 20 nm, attained an average fatigue life of 10,800 cycles and an actuation strain of 2.5%. Samples with intermediate precipitate sizes after aging at 600 °C for 10 h failed at the shortest average fatigue life of 8,200 cycles with an intermediate average actuation strain of 2.0%. Furthermore, increase in UCT decreased the fatigue life and resulted in larger average actuation strains for all samples. Overall, the current findings constitute the first systematic results demonstrating the microstructure dependence of the evolution of actuation strain, irrecoverable strain, and transformation temperatures during actuation fatigue, and actuation fatigue life of the Ni-rich Ni 50.3 Ti 29.7 Hf 20 HTSMA, demonstrating the importance of controlling the H-phase precipitate size.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effects of composition and crystallographic ordering on the ferromagnetic transition in Ni–Co–Mn–In magnetic shape memory alloys

In the present study, the effects of composition and the level of crystallographic ordering were studied in Ni 45 Co 5 Mn 50-X In X magnetic shape memory alloys with X = 13.55, 13.71 and 13.92, in order to reveal the relationship between the Curie temperature (T C ) of the austenite phase and the degree of L2 1 ordering. Various samples were prepared using secondary heat treatments at different temperatures below the order-disorder transition temperature and for different durations, after solution heat treatment, in order to control the degree of ordering. T C s were determined using calorimetric and magnetometry measurements. The relationship between the T C and the degree of order was used to predict the evolution of the order during selected heat treatments. It was shown that the T C of austenite exhibits a monotonous non-linear dependence on the fraction of the L2 1 phase. This relationship was corroborated via ab initio numerical calculations within a mean field approximation. Dependence of the crystallographic order parameter on temperature and duration of secondary heat treatments showed that ordering kinetics is fast, the total degree of order depends only on the annealing temperature and cooling rate for long enough treatments, and maximum achievable degree of order is limited by the low thermal energy available for atomic diffusion at low temperatures. Lastly, small changes in composition were observed to have a significant impact on martensitic transformation temperatures, and a significant but smaller effect on the ferromagnetic transition in these systems.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Analysis of Magnetization as a Function of Temperature for CoMn{sub 1−x}Fe{sub x}Ge

Our experimental measurements for the magnetization M as a function of temperature are analyzed for the multilayer structure of CoMn{sub 1−x}Fe{sub x}Ge for x = 0.085 and x = 0.12 at constant magnetic fields of 3, 5, and 7 T. For this analysis, a power-law formula is used below the transition temperature T{sub C} for these compositions and the values of the critical exponent β for the magnetization M (order parameter) are determined. Our analysis indicates that a first order transition at lower concentrations (x = 0.085) changes toward a second order at higher concentrations (x = 0.12) at constant magnetic fields (3, 5, and 7 T) for the multilayer CoMn{sub 1−x}Fe{sub x}Ge, as observed experimentally.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2015

Tailored thermal expansion alloys

Current approaches to tailoring the thermal expansion coefficient of materials or finding materials with negative thermal expansion rely on careful manipulation of either the material's composition and/or the complex fabrication of composites. By contrast, we report a new principle that enables the precise control of macroscopic thermal expansion response of bulk materials via crystallographic texture manipulation and by taking advantage of anisotropic Coefficients of Thermal Expansion (CTE) in a large class of martensitically transforming materials. Through simple thermo-mechanical processing, it is possible to tailor the thermal expansion response of a single material––without manipulating its composition––over a wide range of positive and negative values. We demonstrate this principle by gradually tuning the macroscopic CTE in a model NiTiPd alloy between a positive (+14.90 × 10 -6 K -1 ) and a negative (-3.06 × 10 -6 K -1 ) value, simply by incrementally increasing tensile plastic deformation in the martensite phase. This surprising response is linked to the large positive, +51.33 × 10 -6 K -1 , and negative, -34.51 × 10 -6 K -1 , CTE anisotropy, at the lattice level, along the different crystal directions in martensite. Similar CTE anisotropy is also shown experimentally in CoNiGa and TiNb alloys. In a model TiNb alloy, giant macroscopic CTEs of +181 × 10 -6 K -1 and -142 × 10 -6 K -1 are measured. A connection between the CTE anisotropy and the martensitic transformation in these and other materials systems such as NiTi, pure uranium, and PbTiO 3 is later made. It is shown that negative or positive thermal expansion crystallographic directions are connected to the crystallographic relationship between the austenite and martensite lattices, and can easily be predicted using the lattice parameters of austenite and martensite phases. Our current observations and analyses suggest that the tunability of the macroscopic CTE through thermo-mechanical processing is universal in materials––both ceramic and metals––that undergo martensitic transformations

36 MATERIALS SCIENCE↗
NASA NTRS2011

Shape Memory Characteristics of Ti(sub 49.5)Ni(sub 25)Pd(sub 25)Sc(sub 0.5) High-Temperature Shape Memory Alloy After Severe Plastic Deformation

A Ti(49.5)Ni25Pd25Sc(0.5) high-temperature shape memory alloy is thermomechanically processed to obtain enhanced shape-memory characteristics: in particular, dimensional stability upon repeated thermal cycles under constant loads. This is accomplished using severe plastic deformation via equal channel angular extrusion (ECAE) and post-processing annealing heat treatments. The results of the thermomechanical experiments reveal that the processed materials display enhanced shape memory response, exhibiting higher recoverable transformation and reduced irrecoverable strain levels upon thermal cycling compared with the unprocessed material. This improvement is attributed to the increased strength and resistance of the material against defect generation upon phase transformation as a result of the microstructural refinement due to the ECAE process, as supported by the electron microscopy observations.

Atli, K. C.↗
NASA NTRS2011

Determining Recoverable and Irrecoverable Contributions to Accumulated Strain in a NiTiPd High-Temperature Shape Memory Alloy During Thermomechanical Cycling

When Ni(29.5)Ti(50.5)Pd30 shape memory alloy is thermally cycled under stress, significant strain can accumulate due to elasticity, remnant oriented martensite and plasticity. The strain due to remnant martensite can be recovered by further thermal cycling under 0 MPa until the original transformation-induced volume change and martensite coefficient of thermal expansion are obtained. Using this technique, it was determined that the 8.15% total accumulated strain after cycling under 200 MPa consisted of 0.38%, 3.97% and 3.87% for elasticity, remnant oriented martensite and creep/plasticity, respectively.

Monroe, J. A.↗
NASA NTRS2010

Comparative Analysis of the Effects of Severe Plastic Deformation and Thermomechanical Training on the Functional Stability of Ti50.5Ni24.5Pd25 High-Temperature Shape Memory Alloy

We compare the effectiveness of a conventional thermomechanical training procedure and severe plastic deformation via equal channel angular extrusion to achieve improved functional stability in a Ti50.5Ni24.5Pd25 high-temperature shape memory alloy. Thermomechanical testing indicates that both methods result in enhanced shape memory characteristics, such as reduced irrecoverable strain and thermal hysteresis. The mechanisms responsible for the improvements are discussed in light of microstructural findings from transmission electron microscopy.

Atli, K. C.↗