Search NASA⌕ Search

Engineering topics

Karkamkar, Abhijeet J.

Publications and source records attributed to Karkamkar, Abhijeet J..

At least 19 records

Investigation of Ammonia Carrier Materials for Next Generation Ammonia Dosing System - CRADA 334 (Abstract)

Lean-burn gasoline and diesel engines can offer substantially higher fuel efficiency, good driving performance, and reduced carbon dioxide emission compared to stoichiometric gasoline engines. Various catalyst technologies have been developed to remove the pollutants from these engines. For example, a three-way catalyst (TWC) is used to remove hydrocarbons (HC), carbon monoxide (CO), and nitrogen oxides (NOx) from gasoline engines during the stoichiometric conditions. During the lean-burn conditions, a TWC or a diesel oxidation catalyst (DOC) is used to control HC and CO emissions. NOx is removed by either lean NOx trap catalyst (LNT) that can store NOx under lean conditions and reduce NOx under rich conditions, or selective catalytic reduction catalyst (SCR) that can selectively remove NOx with a reducing agent. Among the NOx reduction catalyst technologies, SCR offers a number of advantages, including excellent NOx reduction efficiency over a wide range of temperatures and overall lower system cost. In fact, the SCR technology using ammonia (NH3) as reductant has been proven effective and used commercially for the removal of NOx emissions from stationary sources since the 1970s. Currently, SCR is being used to meet the NOx emission standards for diesel engines in Europe and North America, and also being considered for meeting the future NOx emission standards for lean-burn gasoline engines. Because of the challenges associated with storage, handling and transportation of ammonia on a vehicle, aqueous urea solution (e.g., Diesel Exhaust Fluid, AdBlue) has been developed as ammonia storage compound for mobile applications. When the aqueous urea solution is sprayed into exhaust gas stream, urea is decomposed to release ammonia, which then reduces NOx over the downstream SCR catalyst. Although aqueous urea solution technology has enabled automakers and engine manufacturers to meet the current NOx emission standards, this process of releasing ammonia requires a hot exhaust gas and sufficient mixing, creating challenges for low temperature NOx emission control and aftertreatment system packaging. For these reasons, alternative technologies have been developed as ammonia sources (e.g., solid urea, ammonium carbamate, metal ammine chloride) during the past few years. These technologies promise more convenient handling and distribution of ammonia sources, and help maximize the low-temperature performance of SCR catalysts and reduce the overall system volume and weight. However, none of these alternative technologies can be successfully implemented without the industry consensus. Therefore, the USCAR SCR work group, which is comprised of representatives from GM, Ford, and Chrysler, has decided to investigate the potential alternative ammonia carriers, define common standard vehicle interfaces, and address personal and environmental safety concerns with part suppliers and chemical companies. Under this CRADA Project, USCAR and Battelle will investigate alternative ammonia carrier materials that are currently under development. Based on the data and information derived under the CRADA project, the USCAR SCR work group plans to build the consensus and make recommendations for the industry.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Investigation of Ammonia Carrier Materials for Next Generation Ammonia Dosing System - CRADA 334 (Abstract)

Lean-burn gasoline and diesel engines can offer substantially higher fuel efficiency, good driving performance, and reduced carbon dioxide emission compared to stoichiometric gasoline engines. Various catalyst technologies have been developed to remove the pollutants from these engines. For example, a three-way catalyst (TWC) is used to remove hydrocarbons (HC), carbon monoxide (CO), and nitrogen oxides (NOx) from gasoline engines during the stoichiometric conditions. During the lean-burn conditions, a TWC or a diesel oxidation catalyst (DOC) is used to control HC and CO emissions. NOx is removed by either lean NOx trap catalyst (LNT) that can store NOx under lean conditions and reduce NOx under rich conditions, or selective catalytic reduction catalyst (SCR) that can selectively remove NOx with a reducing agent. Among the NOx reduction catalyst technologies, SCR offers a number of advantages, including excellent NOx reduction efficiency over a wide range of temperatures and overall lower system cost. In fact, the SCR technology using ammonia (NH3) as reductant has been proven effective and used commercially for the removal of NOx emissions from stationary sources since the 1970s. Currently, SCR is being used to meet the NOx emission standards for diesel engines in Europe and North America, and also being considered for meeting the future NOx emission standards for lean-burn gasoline engines. Because of the challenges associated with storage, handling and transportation of ammonia on a vehicle, aqueous urea solution (e.g., Diesel Exhaust Fluid, AdBlue) has been developed as ammonia storage compound for mobile applications. When the aqueous urea solution is sprayed into exhaust gas stream, urea is decomposed to release ammonia, which then reduces NOx over the downstream SCR catalyst. Although aqueous urea solution technology has enabled automakers and engine manufacturers to meet the current NOx emission standards, this process of releasing ammonia requires a hot exhaust gas and sufficient mixing, creating challenges for low temperature NOx emission control and aftertreatment system packaging. For these reasons, alternative technologies have been developed as ammonia sources (e.g., solid urea, ammonium carbamate, metal ammine chloride) during the past few years. These technologies promise more convenient handling and distribution of ammonia sources, and help maximize the low-temperature performance of SCR catalysts and reduce the overall system volume and weight. However, none of these alternative technologies can be successfully implemented without the industry consensus. Therefore, the USCAR SCR work group, which is comprised of representatives from GM, Ford, and Chrysler, has decided to investigate the potential alternative ammonia carriers, define common standard vehicle interfaces, and address personal and environmental safety concerns with part suppliers and chemical companies. Under this CRADA Project, USCAR and Battelle will investigate alternative ammonia carrier materials that are currently under development. Based on the data and information derived under the CRADA project, the USCAR SCR work group plans to build the consensus and make recommendations for the industry.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

From Bulk to Interface: Solvent Exchange Dynamics and Their Role in Ion Transport and the Interfacial Model of Rechargeable Magnesium Batteries

Multivalent battery chemistries have been explored in response to the increasing demand for high-energy rechargeable batteries utilizing sustainable resources. Solvation structures of working cations have been recognized as a key component in the design of electrolytes; however, most structure–property correlations of metal ions in organic electrolytes usually build upon favorable static solvation structures, often overlooking solvent exchange dynamics. We here report the ion solvation structures and solvent exchange rates of magnesium electrolytes in various solvents by using multimodal nuclear magnetic resonance (NMR) analysis and molecular dynamics/density functional theory (MD/DFT) calculations. These magnesium solvation structures and solvent exchange dynamics are correlated to the combined effects of several physicochemical properties of the solvents. Moreover, Mg 2+ transport and interfacial charge transfer efficiency are found to be closely correlated to the solvent exchange rate in the binary electrolytes where the solvent exchange is tunable by the fraction of diluent solvents. Our primary findings are (1) most battery-related solvents undergo ultraslow solvent exchange coordinating to Mg 2+ (with time scales ranging from 0.5 μs to 5 ms), (2) the cation transport mechanism is a mixture of vehicular and structural diffusion even at the ultraslow exchange limit (with faster solvent exchange leading to faster cation transport), and (3) an interfacial model wherein organic-rich regions facilitate desolvation and inorganic regions promote Mg 2+ transport is consistent with our NMR, electrochemistry, and cryogenic X-ray photoelectron spectroscopy (cryo-XPS) results. In conclusion, this observed ultraslow solvent exchange and its importance for ion transport and interfacial properties necessitate the judicious selection of solvents and informed design of electrolyte blends for multivalent electrolytes.

25 ENERGY STORAGE↗

Bioinspired Catalyst Design Principles: Progress in Emulating Properties of Enzymes in Synthetic Catalysts

Catalysis enables many aspects of modern life, including fuels, products, plastics, and medicines. Recent advances in catalysis have enabled us to realize higher efficiencies and new processes. Ideally, we seek to achieve high rates of selective conversions using catalysts derived from abundantly available elements and operating under mild conditions, specifically lower reaction temperatures and pressures. Such catalysts could enable decentralized, on-demand synthesis of chemicals and energy carriers. Nature has demonstrated the feasibility of this approach with enzymes, which showcase catalytic processes at low temperatures and pressures with nonprecious metals. Current thinking holds that in addition to the active site, the complexity of the enzyme structure, specifically the protein scaffold, is also critical to achieving this performance. Recreating this environment has been a long-standing scientific goal. However, we still understand the functions of enzymes better than we understand the de novo design of catalysts that mimic enzymes features, while also retaining their activity and selectivity under more demanding conditions. Here, in this Perspective, we will critically examine four key areas of catalyst design that incorporate the chemical and structural properties of enzymes into synthetic catalysts: (i) the use of confinement to enhance catalytic activity, (ii) tailoring the environment around the active site, (iii) proton transport, and (iv) bifunctionality and cooperativity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Molecular Iodine Interactions with Metal Substrates: Towards the Understanding of Iodine Interactions in the Environment Following a Nuclear Accident

In order to evaluate the potential impacts to the public from radioiodine in a nuclear event, it is vital to expand our understanding of the interaction of molecular iodine with various surfaces. There are many potential surfaces that iodine could interact with in and around a nuclear facility, including stainless steel. This study, carried out at ambient temperature, pressure and humidity, demonstrates the highly adsorptive nature of molecular iodine on two types of austenitic stainless steel, 304L and 316L. In the authors review of available literature, Fe is the only metal in stainless steel that is assumed to react with gas-phase molecular iodine. By using a novel approach which combines Inductively Coupled Plasma-Optical Emission Spectroscopy (ICP-OES) with surface Energy Dispersive X-ray Spectroscopy (EDS) there is evidence of the formation of metal iodides that have not previously been verified or quantified. Samples exposed to gaseous molecular iodine formed an iodine containing corrosion product visible by scanning electron microcopy (SEM). Evaluation of the metals in the corrosion region using EDS was compared to a water leach of the same samples analyzed using ICP-OES. A comparison of the results provide evidence that the water leachate is representative of the corrosion layer and not the base material. Furthermore, it provides confirmation of metal iodide formation with minor stainless-steel constituents including: FeI2, NiI2, MnI2 and CrI2.

Beck, Chelsie L.↗

Simultaneous electrocatalytic hydrogenation of aldehydes and phenol over carbon-supported metals

Electrocatalytic hydrogenation of furfural, benzaldehyde, and phenol was studied on carbon-supported Rh, Ru, Pd, and Cu catalysts. All metals were active for hydrogenation of the carbonyl group in furfural and benzaldehyde, but only Rh/C was active for phenol hydrogenation. The intrinsic activities for furfural and benzaldehyde conversion were Pd/C < Ru/C ? Rh/C < Cu/C and Ru/C < Rh/C < Pd/C < Cu/C, respectively. While the trend in furfural hydrogenation remained the same in the presence of phenol, the trend in benzaldehyde hydrogenation in the presence of phenol changed to Rh/C < Ru/C < Pd/C < Cu/C. The Faradaic efficiencies for hydrogenation of both furfural (in the 10–40% range) and benzaldehyde (in the 45–100% range) followed the trend: Cu/C < Rh/C < Ru/C < Pd/C. When phenol and an aldehyde were present in the reactant solution, phenol hydrogenation (only observed on Rh) was suppressed. In contrast, enhancements in the rates of carbonyl reduction were observed for both aldehydes in presence of phenol. Such enhancements depend on both the aldehyde and the metal catalyst. The enhancing factors for hydrogenation of furfural and benzaldehyde were in the 1.5–2 and 2–4 ranges, respectively. We conclude that intermolecular interactions between adsorbed phenol and the aldehydes is a general phenomenon that can potentially enhance the rates of carbonyl hydrogenation. This work highlights co-adsorption effects that pose both challenges and advantages for electrocatalytic reduction of organic compounds.

Electrocatalytic hydrogenation, metal catalysts, p↗

Electrocatalytic Hydrogenation of Biomass-Derived Organics: A review

Sustainable energy generation calls for a shift away from centralized, high-temperature, energy-intensive processes to decentralized, low-temperature conversions that can be powered by electricity produced from renewable sources. Electrocatalytic conversion of biomass-derived feedstocks would allow carbon recycling of distributed, energy-poor resources in the absence of sinks and sources of high-grade heat. Selective, efficient electrocatalysts that operate at low temperatures are needed for electrocatalytic hydrogenation (ECH) to upgrade the feedstocks. For effective generation of energy-dense chemicals and fuels, two design criteria must be met: (i) a high H:C ratio via ECH to allow for high-quality fuels and blends, and (ii) a lower O:C ratio in the target molecules via electrochemical decarboxylation/deoxygenation to improve the stability of fuels and chemicals. The goal of this review is to determine whether the following questions have been sufficiently answered in open literature, and if not, what additional information is required: (1) What organic functionalities are accessible for electrocatalytic hydrogenation under a set of reaction conditions? How do substitutions and functionalities impact the activity and selectivity of ECH? (2) What material properties cause an electrocatalyst to be active for ECH? Can general trends in ECH be formulated based on the type of electrocatalyst? (3) What is the impact of reaction (electrolyte concentration, pH, operating potential) and reactor type conditions?

Catalysts, redox reactions, hydrocarbons, Aromatic↗

Heterolytic Scission of Hydrogen Within a Crystalline Frustrated Lewis Pair

We report the heterolysis of molecular hydrogen under ambient conditions by the crystalline frustrated Lewis pair (FLP) 1-{2-[bis(pentafluorophenyl)boryl]phenyl}-2,2,6,6-tetramethylpiperidine (KCAT). The gas–solid reaction provides an approach to prepare the solvent-free, polycrystalline ion pair KCATH2 through a single crystal to single crystal transformation. The crystal lattice of KCATH2 increases in size relative to the parent KCAT by approximately 2%. Microscopy was used to follow the transformation of the highly colored red/orange KCAT to the colorless KCATH2 over a period of 2 h at 300 K under a flow of H2 gas. There is no evidence of crystal decrepitation during hydrogen uptake. Inelastic neutron scattering employed over a temperature range from 4–200 K did not provide evidence for the formation of polarized H2 in a precursor complex within the crystal at low temperatures and high pressures. However, at 300 K, the INS spectrum of KCAT transformed to the INS spectrum of KCATH2. Calculations suggest that the driving force is more favorable in the solid state compared to the solution or gas phase, but the addition of H2 into the KCAT crystal is unfavorable. Ab Initio methods were used to calculate the INS spectra of KCAT, KCATH2, and a possible precursor complex of H2 in the pocket between the B and N of crystalline KCAT. Ex-situ NMR showed that the transformation from KCAT to KCATH2 is quantitative and our results suggest that the hydrogen heterolysis process occurs via H2 diffusion into the FLP crystal with a rate-limiting movement of H2 from inactive positions to reactive sites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Physi-sorption of H 2 on pure and boron-doped graphene monolayers: A dispersion-corrected DFT study

Carbon based materials are of interest as potential candidates for H 2 storage. Earlier work has been inconclusive on the effect of boron doping on the energy of H 2 binding. However, earlier work has been inconclusive on the definitive effect of boron doping on the energy of H 2 binding, i.e. isosteric heats of adsorption (Qst). In this work, we completed a systematic DFT study to evaluate this effect, and found that doping graphene with boron provides only minor enhancement in H 2 binding. More importantly, the presence of the electron deficient boron into a graphene ring introduces a defect, such as terminal hydrogen or distortion from planarity, which creates hydrogen adsorption sites with slightly increased Qst. The increase is from ~ 5 kJ/mol H 2 for the pure carbon matrix to ~6 - 7 kJ/mol for the boron doped system. The more strongly bond H 2 is located near the defect and shows little direct interaction with the boron. Most significant enhancement is found in systems where H 2 is confined between layers at a distance of about 7Å. In this case, the H 2 binding nearly doubles, to ~10 kJ/mol for both pure, undistorted graphene, and the 2% boron doped system, containing tetrahedral C atom distortion. Interestingly, at higher doping levels of boron, we found that the Qst decreases compared to the all carbon materials. These finding suggest that interplanar nanoconfinement may be more effective way to enhance H 2 binding than boron doping.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Performance of Base and Noble Metals for Electrocatalytic Hydrogenation of Bio-Oil-Derived Oxygenated Compounds

Electrocatalytic hydrogenation is a particularly attractive approach for converting the most unstable compounds in biogenic feedstocks at ambient conditions without external hydrogen. Here, we synthesized a variety of carbon-supported transition metal catalysts and characterized their activity for the electrocatalytic hydrogenation of a series of model compounds and pyrolysis oil. Carbonyl compounds, especially aromatic aldehydes, such as furfural and benzaldehyde, are particularly inclined to hydrogenation driven by an applied current. This was verified with pure solutions of the model compounds and with pyrolysis oil, where we achieved stable and steady continuous operation on Pd. By choosing the optimal catalyst composition, the conversion of benzaldehyde shifted from alcohol production (e.g., on Pd and Cu) to dimerization (e.g., on Co, Ni, and Zn). Pd and Cu were shown to offer the best compromise between reaction rates and efficiency although, in general, base metals offer similar conversions but better efficiencies that noble metals. Thus, the present work offers foundational results and guidelines for choosing the optimal metal catalyst and the applied potential for processing organic feedstocks as a function of its composition.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Electrochemically tunable proton-coupled electron transfer in Pd-catalyzed benzaldehyde hydrogenation

Acid-functionalization of carbon support allows enhancing the electrocatalytic activity of Pd to hydrogenate benzaldehyde to benzyl alcohol in proportion to the concentration of Brønsted acid sites. The hydrogenation rate is not enhanced when H2 is used. The rate enhancement is attributed to differences in the hydrogenation mechanism between the electrochemical and the H2 induced hydrogenations, in particular to the participation of hydronium ions formed at Brønsted acid sites at the perimeter of metal particles in proton coupled electron transfer.

Koh, Katherine↗

Understanding the Role of Metal and Molecular Structure on the Electrocatalytic Hydrogenation of Oxygenated Organic Compounds

Electrocatalytic hydrogenation is increasingly studied as an alternative to integrate the utilization of recycled carbon feedstocks with renewable energy sources. However, the abundant empiric observations available have not been correlated with fundamental properties of substrates and catalysts. In this paper, we investigated the electrocatalytic hydrogenation of homologues series of carboxylic acids, ketones, phenolics, and aldehydes on a variety of metals (Pd, Rh, Ru, Cu, Ni, Zn, and Co). We found that the rates of carbonyl reduction in aldehydes correlate with the corresponding binding energies between the aldehydes and the metals according to the Sabatier principle. That is, the highest rates are obtained at intermediate binding energies. The rates of H 2 evolution, occurring in parallel to hydrogenation, also correlate with the H-metal binding energies, following the same Volcano-type behavior. Within the boundaries of this model (e.g., compounds reactive at room temperature and without important steric effects over the carbonyl group), the reported correlations help to explain the complex trends derived from the experimental observations, allowing for the correlation of rates with binding energies and the differentiation of mechanistic routes.

Sabatier principle↗

Solid-state hydrogen rich boron–nitrogen compounds for energy storage

Boron compounds have a rich history in energy storage applications, ranging from high energy fuels for advanced aircraft to hydrogen storage materials for fuel cell applications. In this paper we review some of the aspects of energy storage materials comprised of electron-poor boron materials combined with electron-rich nitrogen elements with the goal of moderate temperature release of hydrogen. The parent compounds of ammonium borohydride, ammonia borane, and diammoniate of diborane provide approaches for storing high gravimetric and volumetric densities of hydrogen. Here we provide a review with a historical perspective and current developments in the area of solid state B and N containing compounds. This review highlights developments in synthesis of ammonia borane and its derivatives over the last 80 years. Thermodynamics and kinetics of hydrogen release in the solid state are discussed. By changing either substituents on the boron and nitrogen atoms or the physical environment by embedding in mesoporous scaffolds, the thermodynamics can be modified to reduce the exothermicity of hydrogen release and minimize formation of volatile impurities. Several mechanistic studies are reviewed identifying the key distinctions between homopolar and heteropolar H 2 release. Strategies for economical and efficient regeneration of the hydrogen storage materials via chemical transformation are critically reviewed. The limited efficiency of these chemical regeneration has limited some of the potential applications.

25 ENERGY STORAGE↗

Toward Polarization-Switched Molecular Pumps

Pumping of fluids is universally performed by using mechanical or thermal compressors. We demonstrate for the first time a new solid-state molecular pumping mechanism induced by switching the adsorption affinity for a gas through polarization of a chromophore under an applied electric field. Mass spectrometry was used to trace refrigerant gas (difluoromethane) uptake on a chromophore-coated capacitor under applied voltage and subsequent desorption when the voltage and electrode polarization was removed showing an exchange capacity of 0.11 mol of refrigerant per liter of chromophore. Calorimetry confirmed a reversible enthalpy change of 9 Kcal/mol in the polarization-induced sorption-desorption process. Here, the present work establishes the principle and feasibility of non-mechanical molecular pumping, which can be exploited for refrigeration, catalysis, gas separation, among many other potential applications.

42 ENGINEERING↗

Directed Hydrogen Bond Placement: Low Viscosity Amine Solvents for CO2 Capture

Capture of CO2 from power generation is required for its conversion or sequestration. Toward this goal, numerous CO2 capture processes have been developed, with the most widely deployed technology utilizing aqueous solutions of amines. Our group has focused on the design of several classes of water-lean solvents in order to identify molecular-level descriptors to control materials properties such as viscosity and regeneration energy. Large scale molecular simulations have shown that strategic placement of hydrogen bonding and tuning of the acid/base equilibria are critical for controlling viscosity at CO2-rich loadings. Here, we extend these principles to a new class of pyridine-based molecules with a secondary amine functionality for binding CO2. The result is a class of water-lean amines that retain high gravimetric capacity (20%) while exhibiting the lowest CO2-rich viscosities (<150 cP, 40 °C) of any 100% concentrated amine currently known. Additionally, these newly identified solvents exhibit regeneration temperatures as low as 60 °C when applying a polarity swing assisted regeneration, resulting in a solvent that can conceptually absorb and desorb CO2 with only a 20 °C temperature swing.

Malhotra, Deepika↗

Monitoring solvent dynamics and ion associations in the formation of cubic octamer polyanion in tetramethylammonium silicate solutions

NMR methods were utilized to monitor the in situ structural and dynamic changes of various species in highly alkaline tetramethylammonium (TMA) silicate solutions. Quantitative 29Si NMR, 1H, 2H, and 17O relaxation NMR, and 1H and 29Si diffusion NMR of silicates, TMA, H2O and D2O demonstrate that the growth of the cubic octamer Q38 is accompanied by reduced water mobility and increasing TMA coordination number per Q38, which reaches an equilibrium value of 4.5 at 15 °C. Temperature-dependent measurements further reveal that the increased control over speciation by TMA at lower temperatures results from the more stable ion associations via slower solvent motions.

Chen, Ying↗

Synthesis and Engineering Materials Properties of Fluid Phase Chemical Hydrogen Storage Materials for Automotive Applications

Among candidates for chemical hydrogen storage in PEM fuel cell automotive applications, ammonia borane (AB, NH3BH3) is considered to be one of the most promising materials due to its high practical hydrogen content of 14-16 wt%. This material is selected as a surrogate chemical for a hydrogen storage system. For easier transition to the existing infrastructure, a fluid phase hydrogen storage material is very attractive and thus, we investigated the engineering materials properties of AB in liquid carriers for a chemical hydrogen storage slurry system. Slurries composed of AB and high temperature liquids were prepared by mechanical milling and sonication in order to obtain stable and fluidic properties. Volumetric gas burette system was adopted to observe the kinetics of the H2 release reactions of the AB slurry and neat AB. Viscometry and microscopy were employed to further characterize slurries engineering properties. Using a tip-sonication method we have produced AB/silicone fluid slurries at solid loadings up to 40wt% (6.5wt% H2) with viscosities less than 500cP at 25°C.

ammonia borane↗