Search NASA⌕ Search

Engineering topics

Karki, Bhupendra

Publications and source records attributed to Karki, Bhupendra.

8 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Direct fabrication and characterization of vertically stacked Graphene/h-BN/Graphene tunnel junctions

We have used a lithography free technique for the direct fabrication of vertically stacked two-dimensional (2D) material-based tunnel junctions and characterized by Raman, AFM, XPS. We fabricated Graphene/h-BN/Graphene devices by direct deposition of graphene (bottom layer), h-BN (insulating barrier) and graphene (top layer) sequentially using a plasma enhanced chemical vapor deposition on Si/SiO 2 substrates. The thickness of the h-BN insulating layer was varied by tuning the plasma power and the deposition time. Samples were characterized by Raman, AFM, and XPS. The I-V data follows the barrier thickness dependent quantum tunneling behavior for equally doped graphene layers. The resonant tunneling behavior was observed at room temperature for oppositely doped graphene layers where hydrazine and ammonia were used for n-doping of one of the graphene layers. The resonance with negative differential conductance occurs when the band structures of the two electrodes are aligned. The doping effect of the resonant peak is observed for varying doping levels. The results are explained according to the Bardeen tunneling model.

2D-materials↗
DOE OSTI2021

Vapor-Phase Intercalation of Cesium into Black Phosphorous

Cesium vapors were charged into black phosphorous (BP) flakes at varied times and at a temperature gradient of 150 °C. The X-ray diffraction (XRD) measurements of these samples suggest a reduction in the strength of van der Waal interactions between BP layers leading to the loss of coherence of out-of-plane peaks. At the same time, the three main Raman modes of BP (A g 1 , B 2 g , and A g 2 ) steadily redshifted as exposure times were increased, with modes B 2 g and A g 2 shifting faster than A g 1 . After initial rapid downshifts of active BP phonon modes, this intercalation strategy showed its limits following prolonged exposure times. Saturation of BP flakes by Cs vapors ensued and the kinetics was fitted with an exponential decay function. Furthermore, the thermoelectric power (TEP) of cesiated BP exhibited an inversion in sign from positive to negative around 400 K, lending credence to the transformation of as-prepared BP which is a p-type semiconductor to an n-type equivalent due to Cs atom intercalation driven shifting of the Fermi level toward the conduction band of BP and the donation of electrons from Cs. Furthermore, density functional theory (DFT) calculations were used to delve deeper into understanding Cs intercalation on the structural evolution of BP.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Vibrational Properties of Pristine and Lithium-Intercalated Black Phosphorous under High-Pressure

Structural evolution of Li-intercalated and pristine black phosphorous (BP) under high-pressure (up to ≈8 GPa) is studied using in situ Raman spectroscopy. Even though both materials show a monotonic blueshift of the out-of-plane vibrational mode (A 1 g ) with pressure, Li-intercalated BP do not show a blueshift until a threshold pressure (2.4 GPa) is reached to compensate the structural expansion caused by intercalation. However, the in-plane modes (B 2g and A 2 g) in each sample respond differently. In the mid-pressure region, they both show redshifts which in Li-intercalated BP is also followed by abrupt blueshifts. Such behavior indicates pressure-induced structural reorganizations inside the material. Computational modeling reveals the existence of a process of P-P bond breaking and reforming in the system due to the redistribution of intercalated Li atoms under pressure. This work shows the significance of combined effect of pressure and intercalation on structural changes in the search for new phases of BP and other two-dimensional (2D) materials.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Intercalation as a versatile tool for fabrication, property tuning, and phase transitions in 2D materials

Recent advances in two-dimensional (2D) materials have led to the renewed interest in intercalation as a powerful fabrication and processing tool. Intercalation is an effective method of modifying the interlayer interactions, doping 2D materials, modifying their electronic structure or even converting them into starkly different new structures or phases. Herein, we discuss different methods of intercalation and provide a comprehensive review of various roles and applications of intercalation in next-generation energy storage, optoelectronics, thermoelectrics, catalysis, etc. The recent progress in intercalation effects on crystal structure and structural phase transitions, including the emergence of quantum phases are also reviewed.

2D materials↗
DOE OSTI2021

Nematic fluctuations in iron-oxychalcogenide Mott insulators

Nematic fluctuations occur in a wide range physical systems from biological molecules to cuprates and iron pnictide high- T c superconductors. It is unclear whether nematicity in pnictides arises from electronic spin or orbital degrees of freedom. We studied the iron-based Mott insulators La 2 O 2 Fe 2 OM 2 M = (S, Se), which are structurally similar to pnictides. Nuclear magnetic resonance revealed a critical slowing down of nematic fluctuations and complementary Mössbauerr spectroscopy data showed a change of electrical field gradient. The neutron pair distribution function technique detected local C 2 fluctuations while neutron diffraction indicates that global C 4 symmetry is preserved. A geometrically frustrated Heisenberg model with biquadratic and single-ion anisotropic terms provides the interpretation of the low temperature magnetic fluctuations. The nematicity is not due to spontaneous orbital order, instead it is linked to geometrically frustrated magnetism based on orbital selectivity. This study highlights the interplay between orbital order and spin fluctuations in nematicity.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Structural and Thermoelectric Properties of Black Arsenic–Phosphorus

Here, we report the structural and temperature dependent transport properties of As x P 1-x (x = 0, 0.2, 0.5, 0.83, 1) alloys. It is observed that black phosphorous (BP)-related phonon modes in the alloy samples are red-shifted with increasing arsenic concentration, while black arsenic-related modes in these samples are blue-shifted with increasing phosphorus concertation. As the arsenic concentration, x increases from 0 to 1, the 4-probe resistance of the As x P 1-x alloys is found to decrease by more than 3 orders of magnitude. The transport studies reveal that samples with the highest arsenic concentration (x = 1 and 0.83) show metallic behavior in the temperature dependence of resistance with a small thermopower at room temperature with an anomalous temperature dependence. In contrast, the samples with high phosphorus concentration (x = 0, 0.2, and 0.5) show very large thermopower values at room temperature reaching a value as high as 803 μV/k for x = 0.2. The temperature dependence of the thermopower of these samples can be well described by the variable range hopping (VRH) mechanism in two-dimensions (2-d), S ~ T 1/3 . Similarly, their 4-probe resistance (R) values can be fitted with 2-d VRH mechanism, R ~ exp(T -1/3 ).

36 MATERIALS SCIENCE↗
DOE OSTI2020

Electrochemical Li Intercalation in Black Phosphorus: In Situ and Ex Situ Studies

A systematic study on electrochemical charge transfer in Li-doped black phosphorous (BP) was carried out by both in-situ and ex-situ Raman scattering. Galvanostatic discharge of dedicated in-situ electrochemical cell for Raman spectroscopy was used to study time evolution of vibrational modes under lithiation. In addition to the peak broadening which is a result of structural expansion, peaks corresponding to all three atomic vibrational modes A 1 g , B 2 g and A 2 g were found to red-shift as a result of lithiation. Peaks B 2 g and A 2 g were shifted about 1.6 times more towards lower wavenumbers in comparison to A 1 g . Further characterizations using optical and electron microscopy showed that the intercalation of BP is highly anisotropic, where channels along the zigzag direction were found to be the easy direction for intercalation. X-ray diffraction on intercalated samples confirmed a reduction of thickness as lithiation weakens interlayer bonding, thus resulting in a partial exfoliation of BP flakes. Here, first principle studies using density function theory (DFT) were used to develop a theoretical model for the intercalation mechanism. The discrepancy between the experimental and the theoretical results was also addressed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗