Search NASA⌕ Search

Engineering topics

Kashikhin, V V

Publications and source records attributed to Kashikhin, V V.

At least 19 records

High-Field Combined-Function Magnets for a 1.5 x 1.5 TeV Muon Collider Storage Ring

Designs and parameters of dipoles and combined-function quadrupoles for bending arc lattice of a 1.5x1.5 TeV muon collider with an average luminosity of 4x1034 cm{sup -2}s{sup -1} are presented. The magnets use the Nb{sub 3}Sn superconductor and provide the required gradients and fields with the appropriate operating margins and field quality. The magnet apertures accommodate tungsten liners to minimize the dynamic heat load in the superconducting coils.

43 PARTICLE ACCELERATORS↗

Measurements of the persistent current decay and snapback effect in Nb3Sn Fermilab-built accelerator prototype magnets

In recent years, Fermilab has been performing an intensive R an D program on Nb{sub 3}Sn accelerator magnets. This program has included dipole and quadrupole magnets for different programs and projects, including LARP and VLHC. A systematic study of the persistent current decay and snapback effect in the fields of these magnets was executed at the Fermilab Magnet Test Facility. The decay and snapback were measured under a range of conditions including variations of the current ramp parameters and flattop and injection plateau durations. This study has mostly focused on the dynamic behavior of the normal sextupole and dodecapole components in dipole and quadrupole magnets respectively. The paper summarizes the recent measurements and presents a comparison with previously measured NbTi magnets.

43 PARTICLE ACCELERATORS↗

Radiation and Thermal Analysis of Superconducting Quadrupoles in the Interaction Region of Linear Collider

Radiation heat deposition in the superconducting magnets of the Interaction Region (IR) of a linear collider can be a serious issue that limits the magnet operating margins and shortens the material lifetime. Radiation and thermal analyses of the IR quadrupoles in the incoming and extraction beam lines of the ILC are performed in order to determine the magnet limits. This paper presents an analysis of the radial, azimuthal and longitudinal distributions of heat deposition in the incoming and disrupted beam doublets. Operation margins of the magnets based on NbTi superconductor are calculated and compared. The radiation and thermal analysis of the ILC IR quadrupoles based on Rutherford type cables was performed. It was found that the peak radiation heat deposition takes place in the second extraction quadrupole QFEX2. The maximum power density in the coil is {approx}17mW/g. This is rather high, comparing to the proton machines (LHC). However, the fast radial decay of the heat deposition together with the high thermal conductivity of the Rutherford type cable limits the coil temperatures to a moderate level. It was determined that both 2-layer and 4-layer QFEX2 magnet designs have thermal margins of a factor of {approx}4 at the nominal gradient of 31.3 T/m. Because of the large margins, these magnets can easily accommodate possible changes in the IR optics and heat deposition levels.

43 PARTICLE ACCELERATORS↗

Field Quality Study of the LARP Nb3Sn 3.7m-Long Quadrupole Models of LQ Series

After the successful test of the first long Nb{sub 3}Sn quadrupole magnet (LQS01), the US LHC Accelerator Research Program (LARP) has assembled and tested a new 3.7 m-long Nb{sub 3}Sn quadrupole (LQS02). This magnet has four new coils made of the same conductor as LQS01 coils, and it is using the same support structure. LQS02 was tested at the Fermilab Vertical Magnet Test Facility with the main goal to confirm that the long models can achieve field gradient above 200 T/m, LARP target for 90-mm aperture, as well as to measure the field quality. These long models lack some alignment features and it is important to study the field harmonics. Previous field quality measurements of LQS01 showed higher than expected differences between measured and calculated harmonics compared to the short models (TQS) assembled in a similar structure. These differences could be explained by the use of two different impregnation fixtures during coil fabrication. In this paper, we present a comparison of the field quality measurements between LQS01 and LQS02 as well as a comparison with the short TQS models. If the result supports the coil fabrication hypothesis, another LQS assembly with all coils fabricated in the same fixture will be produced for understanding the cause of the discrepancy between short and long models.

43 PARTICLE ACCELERATORS↗

Model NbTi Helical Solenoid Fabrication and Test Results

A program to develop model magnets for a helical cooling channel is under way at Fermilab. In the first steps of a planned sequence of magnets, two four-coil helical solenoid models with 300 mm aperture have been fabricated and tested. These two models, HSM01 and HSM02, used insulated NbTi Rutherford cable wound onto stainless steel rings with spliceless transitions between coils. Strip heaters were included for quench protection of each coil, and the coils were epoxy-impregnated after winding inside the support structures. Based on the results of the first model the second model was made using a cable with optimized cross-section, improved winding and epoxy-impregnation procedures, enhanced ground insulation, and included heat exchange tubing for a test of conduction cooling. We report on the results and lessons learned from fabrication and tests of these two models.

36 MATERIALS SCIENCE↗

Test Results of 15 T Nb3Sn Quadrupole Magnet HQ01 with a 120 mm Bore for the LHC Luminosity Upgrade

In support of the luminosity upgrade of the Large Hadron Collider (LHC), the US LHC Accelerator Research Program (LARP) has been developing a 1-meter long, 120 mm bore Nb{sub 3}Sn IR quadrupole magnet (HQ). With a short sample gradient of 219 T/m at 1.9 K and a conductor peak field of 15 T, the magnet will operate under higher forces and stored-energy levels than that of any previous LARP magnet models. In addition, HQ has been designed to incorporate accelerator quality features such as precise coil alignment and adequate cooling. The first 6 coils (out of the 8 fabricated so far) have been assembled and used in two separate tests-HQ01a and HQ01b. This paper presents design parameters, summary of the assemblies, the mechanical behavior as well as the performance of HQ01a and HQ01b.

43 PARTICLE ACCELERATORS↗

Test Results of the First 3.7 m Long Nb3Sn Quadrupole by LARP and Future Plans

In December 2009 during its first cold test, LQS01, the first Long Nb{sub 3}Sn Quadrupole made by LARP (LHC Accelerator Research Program, a collaboration of BNL, FNAL, LBNL and SLAC), reached its target field gradient of 200 T/m. This target was set in 2005 by the US Department of Energy, CERN and LARP, as a significant milestone toward the development of Nb{sub 3}Sn quadrupoles for possible use in LHC luminosity upgrades. LQS01 is a 90 mm aperture, 3.7 m long quadrupole using Nb{sub 3}Sn coils. The coil layout is equal to the layout used in the LARP Technological Quadrupoles (TQC and TQS models). Pre-stress and support are provided by a segmented aluminum shell pre-loaded using bladders and keys, similarly to the TQS models. After the first test the magnet was disassembled, reassembled with an optimized pre-stress, and reached 222 T/m at 4.5 K. In this paper we present the results of both tests and the next steps of the Long Quadrupole R and D.

43 PARTICLE ACCELERATORS↗

Field Quality of the First LARP Nb3Sn 3.7 m-Long Quadrupole Model of LQ Series

The US-LHC accelerator research program (LARP) built and tested the first 3.7-m long Nb{sub 3}Sn quadrupole model of LQ series with a 90 mm bore diameter and a target field gradient of 200 T/m. The LQ series, developed in collaboration among FNAL, LBNL and BNL, is a scale up of the previously tested 1-m long technology quadrupoles of TQ series based on similar coils and two different mechanical structures (shell-based TQS and collar-based TQC), with a primary goal of demonstrating the Nb{sub 3}Sn accelerator magnet technology for the luminosity upgrade of LHC interaction regions. In this paper, we present the field quality measurements in the first 3.7-m long LQS01 model based on the modified TQS mechanical structure. The results are compared to the expectations from the magnet geometry and magnetic properties of coils and iron yoke. Moreover, we present a comparison between this magnet and the short models previously measured.

43 PARTICLE ACCELERATORS↗

Fabrication and test of 4m long Nb3Sn quadrupole coil made of RRP-114-127 strand

Fermilab is collaborating with LBNL and BNL (US-LARP collaboration) to develop a large-aperture Nb{sub 3}Sn superconducting quadrupole for the Large Hadron Collider (LHC) luminosity upgrade. Several two-layer quadrupole models of the 1-meter and 3.4-meter length with 90mm apertures have been fabricated and tested by the US-LARP collaboration. High-Jc RRP-54/61 strand was used for nearly all models. Large flux jumps typical for this strand due to the large sub-element diameter limited magnet quench performance at temperatures below 2.5-3K. This paper summarizes the fabrication and test by Fermilab of LQM01, a long quadrupole coil test structure (quadrupole mirror) with the first 3.4m quadrupole coil made of more stable RRP-114/127 strand. The coil and structure are fully instrumented with voltage taps, full bridge strain gauges and strip heaters to monitor preload, thermal properties and quench behavior. Measurements during fabrication are reported, including preload during the yoke welding process. Testing is done at 4.5K, 1.9K and a range of intermediate temperatures. The test results include magnet strain and quench performance during training, as well as quench studies of current ramp rate and temperature dependence from 1.9K to 4.5K.

43 PARTICLE ACCELERATORS↗

Mu2e production solenoid cryostat conceptual design

Mu2e is a muon-to-electron conversion experiment being designed by an international collaboration of more than 65 scientists and engineers from more than 20 research institutions for installation at Fermilab. The experiment is comprised of three large superconducting solenoid magnet systems, production solenoid (PS), transport solenoid (TS) and detector solenoid (DS). A 25 kW, 8 GeV proton beam strikes a target located in the PS creating muons from the decay of secondary particles. These muons are then focused in the PS and the resultant muon beam is transported through the TS towards the DS. The production solenoid presents a unique set of design challenges as the result of high radiation doses, stringent magnetic field requirements, and large structural forces. This paper describes the conceptual design of the PS cryostat and will include discussions of the vacuum vessel, thermal shield, multi-layer insulation, cooling system, cryogenic piping, and suspension system.

43 PARTICLE ACCELERATORS↗

Conceptual design of the Mu2e production solenoid cold mass

The Muon-to-Electron conversion experiment (Mu2e), under development at Fermilab, seeks to detect direct muon to electron conversion to provide evidence for a process violating muon and electron lepton number conservation that cannot be explained by the Standard Model of particle physics. The required magnetic field is produced by a series of superconducting solenoids of various apertures and lengths. This paper describes the conceptual design of the 5 T, 4 m long solenoid cold mass with 1.67 m bore with the emphasis on the magnetic, radiation and thermal analyses.

43 PARTICLE ACCELERATORS↗