Search NASA⌕ Search

Engineering topics

Kastengren, A L

Publications and source records attributed to Kastengren, A L.

Modeling the influence of nozzle-generated turbulence on diesel sprays

The physical mechanisms governing spray breakup in direct injection engines, such as aerodynamic induced instabilities and nozzle-generated cavitation and turbulence, are not well understood due to the experimental and computational limitations in resolving these processes. Recent x-ray and visible extinction measurements have been con-ducted with a targeted interest in the spray formation region in order to characterize the distribution of droplet sizes throughout the spray. Detailed analysis of these measurements shows promise of yielding insight into likely mechanisms governing atomization, which can inform the improvement of spray models for engine computational fluid dynamic (CFD) codes. In order to investigate potential atomization mechanisms, we employ a joint experimental and computational approach to characterize the structure of the spray formation region using the Engine Combustion Network Spray D injector. X-ray tomography, radiography and ultra-small angle x-ray scattering measurements conducted at the Advanced Photon Source at Argonne National Laboratory quantify the injector geometry, liquid fuel mass and Sauter mean diameter (SMD) distributions under non-vaporizing conditions. Diffused back-illumination imaging measurements, conducted at the Georgia Institute of Technology, characterize the asymmetry of the spray structure. The selected range of injection pressures (50 – 150 MPa) and ambient densities (1.2 – 22.8 kg/m3) allow for the influence of aerodynamic forces on the spray to be studied in a controlled and systematic manner, while isolating the atomization process from the effects of vaporization. In comparison to high ambient density conditions, the spray is observed to be more asymmetric at low ambient density conditions. Although several mechanisms may cause asymmetries in the nozzle exit flow conditions and ultimately the spray distribution, irregularities in the internal nozzle geometry were identified, suggesting an increased sensitivity of the spray structure to internal nozzle surface finish imperfections at such conditions. The presence of these asymmetries may influence the ability to interpret line-of-sight measurements and their derived SMD values and trends from a single viewing angle of the spray. With this consideration in mind, the measured local sensitivities to ambient density suggest that for ambient densities less than 2.4 kg/m3, aerodynamic effects are likely suppressed, allowing the influence of turbulent-induced breakup to be isolated. In concert with the experimental measurements, we utilize three-dimensional, CFD Lagrangian-Eulerian spray simulations in CONVERGE to evaluate the details of the predicted spray structure. In particular, we compare measured and predicted sensitivities of the SMD distribution to changes in injection and ambient conditions from three different atomization models, namely Kelvin Helmholtz (KH), KH Aerodynamics Cavitation Turbulence (KH-ACT), and the newly developed KH-Faeth hybrid model. While none of the existing hybrid spray models were able to replicate the experimentally observed sensitivities, it was found that the scales characterizing the KH-Faeth model show promise of capturing the experimentally observed trends if the effects of secondary droplet breakup are neglected. These results inform recommendations for future experiments and computational studies that can guide the development of an improved spray breakup model.

33 ADVANCED PROPULSION SYSTEMS↗

X-ray Spray Diagnostics: Comparing Sources and Techniques

Unveiling the internal structure of sprays for propulsion applications is difficult under conditions with high optical extinction. While a number of laser-based techniques have been utilized at intermediate to high optical densities of 2 to 4 (Log10 scale), it is difficult to extract quantitative information under these conditions. The ability of X-rays to penetrate even the most optically dense sprays has enabled quantitative investigation of liquid volume fractions for a variety of applications. Much of the development in this area has taken place utilizing the Advanced Photon Source at Argonne National Laboratory. This paper makes a comparison between two sources: including the bright, coherent, monochromatic, pulsed beam at the Advanced Photon Source and an incoherent, polychromatic, sealed-tube source at the X-ray Flow Visualization Facility at Iowa State University. Studies of dense sprays and static fluid samples were conducted at both facilities to compare performance characteristics of each source for a variety of operating conditions. Data for solid-cone and impinging-jet sprays are presented, and challenges with utilizing polychromatic, incoherent sources are discussed.

43 PARTICLE ACCELERATORS↗

The effects of diesel injector needle motion on spray structure.

The internal structure of diesel fuel injectors is known to have a significant impact on the steady-state fuel distribution within the spray. However, little experimental or computational work has been performed on the dynamics of fuel injectors. Recent studies have shown that it is possible to measure the three-dimensional geometry of the injector nozzle, and to track changes in that geometry as the needle opens and closes in real time. This has enabled the dynamics of the injector to be compared with the dynamics of the spray, and allows computational fluid dynamics (CFD) simulations to use realistic time-dependent flow passage geometries. In this study, X-ray phase-enhanced imaging has been used to perform time-resolved imaging of the needle seat area in several common-rail diesel injection nozzles. The fuel distributions of the sprays emitted by these injectors were also studied with fast X-ray radiography. Correlations between eccentric motions of the injector needle valve and oscillations in the fuel density as it emerges from the nozzle are examined. CFD modeling is used to interpret the effect of needle motion on fuel flow.

33 ADVANCED PROPULSION SYSTEMS↗

Measurement of biodiesel blend and conventional diesel spray structure using x-ray radiography.

The near-nozzle structure of several nonevaporating biodiesel-blend sprays has been studied using X-ray radiography. Radiography allows quantitative measurements of the fuel distribution in sprays to be made with high temporal and spatial resolution. Measurements have been made at different values of injection pressure, ambient density, and with two different nozzle geometries to understand the influences of these parameters on the spray structure of the biodiesel blend. These measurements have been compared with corresponding measurements of Viscor, a diesel calibration fluid, to demonstrate the fuel effects on the spray structure. Generally, the biodiesel-blend spray has a similar structure to the spray of Viscor. For the nonhydroground nozzle used in this study, the biodiesel-blend spray has a slightly slower penetration into the ambient gas than the Viscor spray. The cone angle of the biodiesel-blend spray is generally smaller than that of the Viscor spray, indicating that the biodiesel-blend spray is denser than the Viscor spray. For the hydroground nozzle, both fuels produce sprays with initially wide cone angles that transition to narrow sprays during the steady-state portion of the injection event. These variations in cone angle with time occur later for the biodiesel-blend spray than for the Viscor spray, indicating that the dynamics of the injector needle as it opens are somewhat different for the two fuels.

33 ADVANCED PROPULSION SYSTEMS↗