Engineering topics

Kastengren, A. L.

Publications and source records attributed to Kastengren, A. L..

5 records

DOE OSTI2022

Energy dispersive x-ray diffraction of luminescent powders: A complement to visible phosphor thermometry

Energy-dispersive x-ray diffraction of thermographic phosphors has been explored as a complementary temperature diagnostic to visible phosphor thermometry in environments where the temperature-dependent optical luminescence of the phosphors is occluded. Powder phosphor samples were heated from ambient to 300°C in incremental steps and probed with polychromatic synchrotron x rays; scattered photons were collected at a fixed diffraction angle of 3.9°. Crystal structure, lattice parameters, and coefficients of thermal expansion were calculated from the diffraction data. Finally, of the several phosphors surveyed, YAG:Dy, ZnO:Ga, and GOS:Tb were found to be excellent candidates for diffraction thermometry due to their strong, distinct diffraction peaks that shift in a repeatable and linear manner with temperature.

47 OTHER INSTRUMENTATION↗

DOE OSTI2021

Temporally and spatially resolved X-ray densitometry in a shock tube

Gas densities were measured by x-ray absorption spectroscopy to examine spatial inhomogeneity in density behind incident and reflected shock waves in a miniature (12.7 mm bore) high repetition rate shock tube. Shock waves were generated in argon. The pressure and temperature behind the incident shock were P 2 ~ 1.72 bar and T 2 ~ 800 K, while those behind the reflected shock were P 5 ~ 6.5 bar and T 5 ~ 1480 K. Time-resolved line-of-sight transmission measurements using x-rays at 9 keV photon energy were made along various axial and transverse locations covering the entire shock tube cross section. The x-ray transmission at each location was converted to pathlength-integrated densities, which in some conditions could be further converted to pathlength-averaged densities. The measured gas densities were compared with those calculated by the normal shock wave relations, and good agreement was found in the preshock and immediately behind the incident shock regions. Similar agreement was found for reflected shock conditions very near the endwall. However, increasingly large differences between the measured and calculated gas densities were found as distance from the endwall increased. Furthermore, reconstruction by Abel inversion allowed time and radially resolved densities to be obtained from the transverse measurements. While the profiles measured in this experiment are of insufficient signal-to noise level and resolution to definitively assign boundary layer thicknesses, future improvements may be able to do this. The radially resolved densities reveal growing sidewall thermal boundary layers in gases behind the reflected shock. These reconstructions were compared with a model of the thermal boundary layer and are consistent with values of the thermal boundary layer thickness being between 0.25 mm and 1 mm at 0.7 ms after shock reflection.

42 ENGINEERING↗

DOE OSTI2021

Evaluation of liquid-phase thermometry in impinging jet sprays using synchrotron x-ray scattering

Liquid thermometry during primary and secondary breakup of liquid sprays is challenging due to the presence of highly dynamic, optically complex flow features. This work evaluates the use of x-ray scattering from a focused, monochromatic beam of the Advanced Photon Source at Argonne National Laboratory for the measurement of liquid temperatures within the mixing zone of an impinging jet spray. The measured scattering profiles are converted to temperature through a previously developed two-component partial least squares (PLS) regression model. Transmitive mixing during jet merging is inferred through spatial mapping of temperatures within the impingement region. In this work, the technique exhibits uncertainties of ±2K in temperature and 2% in capturing the correct scattering profile, showing its potential utility for probing liquid temperature distributions in multiphase flows.

42 ENGINEERING↗

DOE OSTI2021

Feasibility of X-ray scattering for tracer-free liquid-phase thermometry for multiphase flows

The feasibility of liquid temperature measurements using X-ray scattering is investigated for liquids with varying properties (water, ethanol, and n-dodecane) on beamline 7-BM at the Advanced Photon Source at Argonne National Laboratory. The temperature is inferred through the change in the scattering pattern from the liquid as a function of temperature using partial least squares regression. An accuracy of ~98% or higher was achieved enabling measurements for a wide range of applications.

42 ENGINEERING↗

DOE OSTI2020

Gaseous jet through an outward opening injector: Details of mixing characteristic and turbulence scales

Direct injection (DI) strategy of natural gas (NG) into internal combustion engines (ICE) has led to higher thermal efficiency and lower exhaust emissions. In order to thoroughly understand the most relevant phenomena affecting the performances of such engines, computational fluid dynamics (CFD) plays a key role as an accurate description of the jet evolution and interaction within the combustion chamber is required to that aim. Accurate description of high-pressure gaseous jets is rather challenging at high Mach numbers, as the injected gas is strongly under-expanded once in the ambient, giving room to shocks due to compressibility effects. Also the interaction between shock waves and mixing layers needs to be carefully represented with a multi-dimensional model, calling for substantial computational resources requirements. In this paper a numerical investigation of the behavior of a gaseous jet (Argon) through an outward opening injector has been carried out. A Large Eddy Simulation (LES) approach has been used in order to track the structures derived by the interaction of the injected fuel with the surrounding ambient. Although already good results were obtained using a Reynolds Averaged Navier-Stokes (RANS) approach, the adoption of LES is required to characterize more accurately the jet properties in terms of vortex structures and mixing effectiveness. Finally, the effect of the Nozzle Pressure Ratio (NPR) on the jet evolution has been highlighted in the paper, showing how a higher NPR would give a faster injection process, compromising however the homogeneity of the mixture.

33 ADVANCED PROPULSION SYSTEMS↗