Engineering topics

Kaul, Brian [ORNL] (ORCID:0000000184813620)

Publications and source records attributed to Kaul, Brian [ORNL] (ORCID:0000000184813620).

8 records

DOE OSTI2026

Examining experimental nitrogen-based emissions trends from ammonia/diesel and ammonia/hydrogen/diesel combustion

Ammonia has garnered interest as an alternative fuel for power sectors with heavy payload and distance requirements, such as shipping. In this study, ammonia was used in a dual-fuel compression-ignition combustion strategy to overcome some of its technical barriers, using a diesel pilot to ignite a premixed mixture of ammonia and air. Mixtures of premixed ammonia and hydrogen were also explored to evaluate whether the inclusion of hydrogen improves nitrogen-based emissions from the combustion process. A single-cylinder version of a Cummins ISB 6.7 L engine platform was used to experimentally study these effects at various global air/fuel ratios and hydrogen energy fractions. Hydrogen inclusion produced pronounced NOx and N2O emissions, while inclusion of trapped residuals increased N2O but reduced NOx. The two most recent and relevant mechanisms available in the literature—those from Xu and Zhang-Ren-Kokjohn—were used in a chemical kinetics analysis to examine the observed differences in the NOx trends from two dual-fuel ammonia/diesel datasets: (1) in which a portion of the premixed ammonia was substituted with hydrogen and (2) in which the effect of hot trapped residuals was evaluated with only ammonia/air premixed mixtures. The analysis with both mechanisms showed agreement with experimental trends; however, contributions from thermal vs. fuel-borne NOx pathways showed disagreement. A reaction pathway analysis showed that the HNO to NO pathway was the key to NO formation in the mixture.

Tyrewala, Daanish [ORNL] (ORCID:0000000208599324)↗

DOE OSTI2026

Evaluation of Bio-Intermediates and Other Biofuels for use in Marine Engines

This paper presents an overview of the DOE Marine Biofuel Feasibility Study to evaluate the potential of biofuels for ocean-going vessels. These vessels operate on low-cost residual fuel oils (also known as heavy fuel oils or HFO), which require significant heating and purification onboard vessels. The industry is looking at economical alternative fuels that can enhance performance from combustion/emissions, rheology, and other perspectives. Four U.S. national laboratories are collaborating to evaluate a variety of biofuels, including bio-intermediates (pyrolysis and hydrothermal liquefaction oils), biodiesel (fatty acid methyl esters or FAME), bio-residuals (FAME byproducts) for their suitability as fuels for marine diesel engines. Bio-intermediates in particular are of interest because large marine engines that operate on HFO can tolerate lowerquality, more viscous fuels and may be able to utilize these fuels with less upgrading than other applications, presenting economic advantages. The test fuels of interest are examined to determine the minimum level of upgrading required for blend compatibility with market HFOs containing high levels of asphaltenes as well as their impact on the viscosity, polymerization tendency, and combustion properties (particularly cetane number) of the fuel blends in preparation for future evaluation in engine studies.

Kaul, Brian [ORNL] (ORCID:0000000184813620)↗

DOE OSTI2025

Dual-Fuel Ammonia Equivalence Ratio Sweep Data

Ammonia (NH3) has garnered significant interest as an alternative fuel for meeting international emissions reduction mandates in sectors with high weight and distance requirements, such as shipping. Technical barriers and unanswered questions remain on the combustion strategies that can maximize ammonia utilization and minimize emissions. Prior research studies at the US Department of Energy’s Oak Ridge National Laboratory have shown strong performance with NH3 under dual-fuel mode using conventional diesel combustion (CDC) manifold air pressure settings. Diesel airflow was initially used to simplify retrofitting (no turbocharger modification), which resulted in air-fuel equivalence ratios (λ) greater than 1.5. To characterize potential improvements in dual-fuel NH3 combustion performance at richer in-cylinder conditions, a global λ sweep compared the use of early (E-pilot) and late (L-pilot) single diesel injections. The experiments were conducted at 1200 RPM and 12.8 ± 0.2 bar (75 % load), and λ was varied by decreasing the commanded air flow to the engine at greater than 90 % ammonia energy substitution level. A diesel injection timing sweep was conducted for both the injection strategies at fixed λ, and the timing with the lowest engine-out N2O emissions was identified. The results indicated an optimal balance between CO2,eq and thermal efficiency benefits both E-pilot and L-pilot injection strategy cases compared with CDC at a λ of 1.4. The indicated nitrogen-based emissions exhibited a strong correlation to the ratio of CA5–50 and ignition delay for L-pilot, but no apparent trend emerged for the E-pilot injection strategy at the tested boundary conditions. This dataset includes the raw experimental data and documentation of the experiment conditions and methods.

30 DIRECT ENERGY CONVERSION↗

DOE OSTI2025

Design and Demonstration of a NH3-Fueled Two-Stroke Uniflow Engine for Greenhouse Gas Reduction

The maritime shipping industry is growing increasingly interested in both low and non-carbon-containing fuels to meet future greenhouse gas emission targets. Specifically of interest is ammonia, as it has a relatively high volumetric energy density compared to other future fuels, such as hydrogen, making it more economical to transport. The robust engine architecture of low-speed two-stroke marine engines makes them an ideal candidate for ammonia fuel, overcoming many of the issues surrounding its poor ignitability and low flame speed. If emissions and fueling system challenges can be addressed, retrofits of current low-speed two-stroke dual-fuel engines represent a viable pathway for bringing ammonia engines to market. This study explores these technical hurdles by describing the design, analysis, and experimental validation of a single cylinder research engine converted to operate on ammonia fuel. The engine is a reduced-scale uniflow two-stroke marine engine with two previous hardware configurations available – diesel and high-pressure CNG dual-fuel. A concept study was used to evaluate possible ammonia-fueled engine architectures and the associated tradeoffs and design considerations. With the chosen architecture, low-pressure dual fuel, 1D and 3D analysis tools were used to inform hardware selection and to determine hardware configurations which minimized ammonia-slip. In addition to these considerations the hardware and engine configuration were designed to provide a versatile and robust testing platform. This includes options to test both gaseous and liquid ammonia injection, as well as a wide range of performance parameters such as AFR, swirl, valve timing, SOI, and many others. Design constraints imposed by the existing engine hardware necessitated an iterative loop between design and analysis toolsets, ultimately converging on a final design for the ammonia-conversion hardware. The engine was rebuilt with the new hardware and evaluated in an engine test cell. A new control strategy developed and flashed onto a prototyping electronic control unit allowed for full control over all engine parameters. An initial calibration was developed, providing test data for validation of the engine 1D and 3D models. The impact of the design choices on engine operability and the ability to meet program targets is discussed as well as opportunities for further optimization of the ammonia-conversion hardware, informed by the validated models.

Kaul, Brian [ORNL] (ORCID:0000000184813620)↗

DOE OSTI2025

Influence of Combustion Gas Temperatures on Piston Deposits for Diesel and Ammonia Dual-Fuel Combustion

As new fuels are adopted for marine engines, it is necessary to understand their impact on lubricant performance. In order to evaluate the performance of existing lubricants and inform the development of new ones, a deposit control test protocol has been developed using the ExxonMobil Enterprise two-stroke marine diesel research engine. Repeated tests at the target speed/load operating condition but different thermal conditions show that the temperature of the combustion gases is a key driver in the formation of deposits on piston surfaces, impacting both the quantity of deposits and whether they are hard or gummy. These impacts are examined for diesel combustion as well as ammonia dual-fuel combustion. Among alternative marine fuels, ammonia has perhaps the most unanswered questions regarding interactions with cylinder lubricants. The influence of ammonia dual-fuel combustion on the thermal conditions experienced by the lubricant are discussed. Scrape down oil samples were collected after operation with ammonia for analysis and comparison with fresh oil. Chemical analysis using a GC/MS instrument did not show significant permanent chemical changes in the lubricant due to ammonia exposure.

Kaul, Brian [ORNL] (ORCID:0000000184813620)↗

DOE OSTI2025

Efficiency and emissions of NH3-diesel/bio-pilot dual-fuel combustion in a high-speed four-stroke engine

While dual-fuel ammonia engines are starting to be commercialized for the large low-speed 2-stroke marine engine market, there are still challenges with utilizing ammonia on 4-stroke engines used as auxiliary engines for ocean going vessels and within inland and coastal marine applications. The shorter timescales for high-speed engines pose a particular challenge for low-cetane, high ignition energy fuels like ammonia. In addition to achieving maximum ammonia substitution levels, N2O emissions are a key factor that needs to be understood. This paper reports the results of experiments using a single-cylinder 107mm bore Cummins B-series diesel engine modified for port-fuel injection of gaseous anhydrous ammonia with a direct injection of diesel fuel near-TDC to ignite the premixed ammonia. Combustion data as well as emissions data from an FTIR including NO, NO2, N2O, and unburned ammonia are presented for selected operating points with a focus on high-load operation at 1200rpm with high ammonia energy substitution (over 95% by fuel energy). Several air/fuel ratio conditions are included, sweeping from diesel-like airflow to stoichiometric conditions. The impact of biofuels (biodiesel and renewable diesel) as pilot fuels is also considered. Comparisons for emissions, greenhouse gas performance, and efficiency are made with a conventional diesel combustion baseline. The impact of fuel injection strategy on NOx, N2O, and NH3 emissions is quantified, and the dual-fuel ammonia results on this high-speed 4-stroke engine are expected to provide fundamental insights into further combustion development opportunities for the larger engines used across marine applications.

Kaul, Brian [ORNL] (ORCID:0000000184813620)↗

DOE OSTI2025

Evolution at the Edge: Real-Time Evolution for Neuromorphic Engine Control

Neuromorphic computing systems are attractive for real-time control at the edge because of their low power operation, real-time processing capabilities and their potential ability to do online learning. In this work, we describe an approach for performing real-time evolution of spiking neural networks for neuromorphic systems at the edge called Neuromorphic Optimization using Dynamic Evolutionary Systems or NODES. We apply this approach to real-time combustion engine control and develop an engine-specific hardware platform for NODES called FireBox. We demonstrate how the real-time evolution approach works in simulation and the performance of networks trained in simulation on the physical engine.

Maldonado Puente, Bryan [ORNL] (ORCID:000000033880↗

DOE OSTI2025

Experimental Investigation of Air-Fuel Equivalence Ratio Effects on Advanced Dual-fuel Diesel/Ammonia Combustion on a Single-Cylinder Medium-Duty Diesel Engine at High Load

Ammonia (NH3) has gathered a lot of interest as a low-lifecycle-carbon fuel in sectors with high weight and distance requirements, such as shipping. The International Maritime Organization (IMO) mandates a 70-80% greenhouse gas (GHG) reduction by 2040, which is only possible with advanced engine technologies and fuels like NH3. Prior research studies at the US Department of Energy’s Oak Ridge National Laboratory have shown strong performance with NH3 under dual-fuel mode using conventional diesel combustion (CDC) manifold air pressure (MAP) settings. Diesel airflow was initially used to simplify retrofitting (no turbocharger modification), which resulted in air-fuel equivalence ratios (λ) greater than 1.5. To characterize potential improvements in dual-fuel NH3 combustion performance at richer in-cylinder conditions, a global λ sweep using a diesel pilot ignition (DPI) strategy with diesel fuel injected near top-dead center (TDC) and a reactivity-controlled compression ignition (RCCI) injection strategy with diesel fuel injected earlier during the compression stroke were compared. The experiments were conducted at 1200 RPM and 12.6 bar (75% load), and λ was varied by decreasing the commanded air flow to the engine at greater than 90% ammonia energy substitution (AES) level. A diesel injection timing sweep was conducted for both the combustion modes at fixed λ, and the timing with the lowest engine-out N2O emissions was identified. The results indicated an optimal balance between CO2, eq and thermal efficiency benefits for both DPI and RCCI injection strategy cases compared to CDC at a λ of 1.4. The indicated N-based emissions exhibited a strong correlation to the ratio of CA5–50 and ignition delay for DPI, but no apparent trend emerged for the RCCI injection strategy at the tested boundary conditions.

Tyrewala, Daanish [ORNL] (ORCID:0000000208599324)↗