Search NASA⌕ Search

Engineering topics

Kaye, S.

Publications and source records attributed to Kaye, S..

At least 37 records · Page 2

Recent progress toward an advanced spherical torus operating point in NSTX

Progress in the development of integrated advanced ST plasma scenarios in NSTX (Ono et al., 2000 Nucl. Fusion 40 557) is reported. Recent high-performance plasmas in NSTX following lithium coating of the plasma facing surfaces have achieved higher elongation and lower internal inductance than previously. Analysis of the thermal confinement in these lithiumized discharges shows a stronger plasma current and weaker toroidal field dependence than in previous ST confinement scaling studies; the ITER-98(y, 2) scaling expression describes these scenarios reasonably well. Analysis during periods free of MHD activity has shown that the reconstructed current profile can be understood as the sum of pressure driven, inductive and neutral beam driven currents, without requiring any anomalous fast-ion transport. Non-inductive fractions of 65–70%, and βP > 2, have been achieved at lower plasma current. Some of these low-inductance discharges have a significantly reduced no-wall βN limit, and often have βN at or near the with-wall limit. Coupled m/n = 1/1 + 2/1 kink/tearing modes can limit the sustained β values when rapidly growing ideal modes are avoided. A βN controller has been commissioned and utilized in sustaining high-performance plasmas. 'Snowflake' divertors compatible with high-performance plasmas have been developed. Scenarios with significantly larger aspect ratios have also been developed, in support of next-step ST devices. Furthermore, these NSTX plasmas have many characteristics required for next-step ST devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Triggered Confinement Enhancement and Pedestal Expansion in High-Confinement-Mode Discharges in the National Spherical Torus Experiment

We report observation of a new high performance regime in discharges in the National Spherical Torus Experiment, where the H mode edge 'pedestal' temperature doubles and the energy confinement increases by 50%. The spontaneous transition is triggered by a large edge-localized mode, either natural or externally triggered by 3D fields. The transport barrier grows inward from the edge, with a doubling of both the pedestal pressure width and the spatial extent of steep radial electric field shear. The dynamics suggest that 3D fields could be applied to reduce edge transport in fusion devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Anomalous Electron Transport Due to Multiple High Frequency Beam Ion Driven Alfven Eigenmode

We report on the simulations of recently observed correlations of the core electron transport with the sub-thermal ion cyclotron frequency instabilities in low aspect ratio plasmas of the National Spherical Torus Experiment (NSTX). In order to model the electron transport of the guiding center code ORBIT is employed. A spectrum of test functions of multiple core localized Global shear Alfven Eigenmode (GAE) instabilities based on a previously developed theory and experimental observations is used to examine the electron transport properties. The simulations exhibit thermal electron transport induced by electron drift orbit stochasticity in the presence of multiple core localized GAE.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The impact of lithium wall coatings on NSTX discharges and the engineering of the Lithium Tokamak eXperiment (LTX)

Recent experiments on the National Spherical Torus eXperiment (NSTX) have shown the benefits of solid lithium coatings on carbon PFC's to diverted plasma performance, in both L- and H-mode confinement regimes. Better particle control, with decreased inductive flux consumption, and increased electron temperature, ion temperature, energy confinement time, and DD neutron rate were observed. Successive increases in lithium coverage resulted in the complete suppression of ELM activity in H-mode discharges. A liquid lithium divertor (LLD), which will employ the porous molybdenum surface developed for the LTX shell, is being installed on NSTX for the 2010 run period, and will provide comparisons between liquid walls in the Lithium Tokamak eXperiment (LTX) and liquid divertor targets in NSTX. LTX, which recently began operations at the Princeton Plasma Physics Laboratory, is the world's first confinement experiment with full liquid metal plasma-facing components (PFCs). All materials and construction techniques in LTX are compatible with liquid lithium. LTX employs an inner, heated, stainless steel-faced liner or shell, which will be lithium-coated. In order to ensure that lithium adheres to the shell, it is designed to operate at up to 500–600 °C to promote wetting of the stainless by the lithium, providing the first hot wall in a tokamak to operate at reactor-relevant temperatures. The engineering of LTX will be discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Advances in High Harmonic Fast Wave Heating of NSTX H-mode Plasmas

High-harmonic fast wave (HHFW) heating and current drive is being developed in NSTX to provide bulk electron heating and q(0) control during non-inductively sustained Hmode plasmas fuelled by deuterium neutral-beam injection (NBI). In addition, it is used to assist the plasma current ramp-up. A major modification to increase the RF power limit was made in 2009; the original end-grounded, single end-powered current straps of the 12- element array were replaced with center-grounded, double end-powered straps. Greater than 3 MW have been coupled into NBI-driven, ELMy H-mode plasmas with this upgraded antenna. Improved core HHFW heating, particularly at longer wavelengths and during low-density start-up and plasma current ramp-up, has been obtained by lowering the edge density with lithium wall conditioning, thereby moving the critical density for fast-wave propagation away from the vessel wall [1]. Significant core electron heating of NBI-fuelled H-modes has been observed for the first time over a range of launched wavelengths and H-modes can be accessed by HHFW alone. Visible and IR camera images of the antenna and divertor indicate that fast wave interactions can deposit considerable RF energy on the outboard divertor plate, especially at longer wavelengths that begin to propagate closer to the vessel walls. Edge power loss can also arise from HHFWgenerated parametric decay instabilities; edge ion heating is observed that is wavelength dependent. During plasmas where HHFW is combined with NBI, there is a significant enhancement in neutron rate, and fast-ion D-alpha (FIDA) emission measurements clearly show broadening of the fast-ion profile in the plasma core. Large edge localized modes (ELMs) have been observed immediately following the termination of RF power, whether the power turn off is programmed or due to antenna arcing. Causality has not been established but new experiments are planned and will be reported. Fast digitization of the reflected power signal indicates a much faster rise time for arcs than for ELMs. Based on this observation, an ELM/arc discrimination system is being implemented to maintain RF power during ELMs even when the reflection coefficient becomes large. This work is supported by US DOE contracts DE-AC-05-00OR22725 and DE-AC02- 09CH11466. References [1] C. K. Phillips, et al, Nuclear Fusion 10, 075015 (2009)

Ryan, Philip Michael↗

SCATHA observations of space plasma composition during a spacecraft charging event

During an Earth eclipse of the SCATHA spacecraft, the spacecraft charged to potentials greater than 1KV for about 30 minutes with extended excursions greater than 4KV. The composition of the hot plasma was obtained in the 0.1 to 32 keV energy range with an ion mass spectrometer aboard the spacecraft. Prior to the onset of the charging event, H(+) was the principal plasma ion, and during the event O(+) was the principal ion. The composition was energy dependent and varied significantly on a time scale of 4 minutes. An assumption that the ion flux was all H(+) led to computed number densities that were in error by more than a factor of two for several time intervals during the event.

Johnson, R. G.↗

Space processing of composite materials

Materials and processes for the testing of aluminum-base fiber and particle composites, and of metal foams under extended-time low-g conditions were investigated. A wetting and dispersion technique was developed, based on the theory that under the absence of a gas phase all solids are wetted by liquids. The process is characterized by a high vacuum environment and a high temperature cycle. Successful wetting and dispersion experiments were carried out with sapphire fibers, whiskers and particles, and with fibers of silicon carbide, pyrolytic graphite and tungsten. The developed process and facilities permit the preparation of a precomposite which serves as sample material for flight experiments. Low-g processing consists then merely in the uniform redistribution of the reinforcements during a melting cycle. For the preparation of metal foams, gas generation by means of a thermally decomposing compound was found most adaptable to flight experiments. For flight experiments, the use of compacted mixture of the component materials limits low-g processing to a simple melt cycle.

Steurer, W. H.↗

Space-related composite-material experiments

The preparation of composites in space depends on the immersion of reinforcements in a liquid-metal matrix and their uniform, stable dispersion in the bulk products until solidification occurs. The chief problem in achieving the composite is associated with the 'wetting' of the reinforcements. A study of the theory of wetting revealed that wetting is prevented by the presence of gaseous and oxide contaminants at the interface between the pure liquid and pure solid. Experiment then confirmed that the use of a vacuum environment, cleaning of all surfaces, elevated temperature, ion bombardment, and vigorous mechanical agitation enabled the immersion and dispersion of candidate reinforcements. The technique is limited by the increased tendency for reaction if the time at elevated temperature is extended.

Kaye, S.↗

Low-gravity dispersion of solids in liquid metals

A number of space processes, particularly the preparation of various types of composite materials, involve mixtures of liquid metals and solid particles. The two predominant problems associated with the attainment of such mixtures are; (1) free dispersion of the solids, possible only if they are perfectly wetted by the liquid, and (2) mixture stability. The results of related experimental investigations and theoretical studies are presented.

Kaye, S.↗

Space processes for extended low-G testing

Results of an investigation of verifying the capabilities of space processes in ground based experiments at low-g periods are presented. Limited time experiments were conducted with the processes. A valid representation of the complete process cycle was achieved at low-g periods ranging from 40 to 390 seconds. A minimum equipment inventory, is defined. A modular equipment design, adopted to assure low cost and high program flexibility, is presented as well as procedures and data established for the synthesis and definition of dedicated and mixed rocket payloads.

Steurer, W. H.↗

Preparation of composite materials in space. Volume 2: Technical report

A study to define promising materials, significant processing criteria, and the related processing techniques and apparatus for the preparation of composite materials in space was conducted. The study also established a program for zero gravity experiments and the required developmental efforts. The following composite types were considered: (1) metal-base fiber and particle composites, including cemented compacts, (2) controlled density metals, comprising plain and reinforced metal foams, and (3) unidirectionally solidified eutectic alloys. A program of suborbital and orbital experiments for the 1972 to 1978 time period was established to identify materials, processes, and required experiment equipment.

Steurer, W. H.↗

Preparation of composite materials in space. Volume 1: Executive summary

The reported objectives were to define promising materials, to obtain significant processing criteria and the related processing techniques and apparatus for the preparation of composites in space, and to establish a program for zero-g experiments and the required developmental efforts. Preparation was studied of the following composite types: (1) metal-base fiber and particle composites, including cemented compacts, (2) controlled density metals, comprising plain and reinforced metal foams, and (3) unidirectionally solidified eutectic alloys. The zero-g environment of orbital operations offers the capability to produce metal-base composite materials and castings which exhibit properties and, particularly, unique combinations of properties that cannot be achieved in terrestrial production.

Steurer, W. H.↗

Preparation and evaluation of Apollo 14 composite experiments

An account is given of the work aimed at flight experiments on Apollo 14, in relation to space manufacturing processes. Evaluation of suitable materials, definition of in-flight processing procedures, preparation of preprocessed materials and delivery, and evaluation of the space-processed samples after return from the Apollo 14 flight are presented.

Steurer, W. H.↗