Search NASA⌕ Search

Engineering topics

Ke, Jia-Hong

Publications and source records attributed to Ke, Jia-Hong.

7 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Flux effects in precipitation under irradiation simulation of Fe-Cr alloys

Radiation-enhanced precipitation of Cr-rich α’ in irradiated Fe-Cr alloys, which results in hardening and embrittlement, depends on the irradiating particle and the displacement per atom (dpa) rate. Here, we utilize a Cahn-Hilliard phase-field based approach, that includes simple models for nucleation, irradiating particle and rate dependent radiation-enhanced diffusion and cascade mixing to simulate α’ evolution under neutrons, heavy ions, and electron irradiations. Different irradiating particles manifest very different cascade mixing efficiencies. The model was calibrated using neutron data. For cascade inducing neutron/heavy-ion dpa rates at 300 °C between 10-8 and 10-6 dpa/s the model predicts approximately constant number density, decreasing radius, decreasing α’ Cr composition, and lower α’ volume fraction. The model then predicts a dramatic transition to no α’ formation above approximately 10-5 dpa/s, while electron irradiation, with weak mixing, had little effect at dpa rates up to 10-3 dpa/s. These model predictions are consistent with experiments. We explain the results in terms of the flux dependence of the radiation enhanced diffusion, cascade mixing, and their ratio, which all vary significantly in relevant flux ranges for neutron and cascade inducing ion irradiations. These results show that both cascade mixing and radiation enhanced diffusion must be accounted for when attempting to emulate neutron-irradiation effects using accelerated ion irradiations.

Ke, Jia-Hong↗
DOE OSTI2024

Multiscale, mechanistic modeling of irradiation-enhanced silver diffusion in TRISO particles

Tristructural isotropic (TRISO) particles are under consideration for use in several proposed advanced nuclear reactor concepts. The silicon carbide (SiC) layer in TRISO acts as a barrier to prevent the release of the fission products. However, despite remarkable retention, silver (Ag) release has been observed from intact particles, which requires investigation since the Ag isotope ( 110m Ag) has a long half-life. Previous work focused on developing a multiscale, mechanistic model for Ag diffusion accounting for temperature and microstructure effect and has been successfully validated. In this work, we expand the previous model to account for irradiation-enhanced Ag diffusivity in SiC and improve its accuracy over a wider grain size and temperature ranges relevant for advanced reactor conditions. A temperature, grain size, and flux dependent diffusivity is therefore derived using the mesoscale code MARMOT and implemented in the fuel performance code BISON. The irradiation-enhanced Ag diffusivity in SiC is compared against experimental data and validated using BISON against Ag release measurements from the Advanced Gas Reactor Fuel Development and Qualification Program (AGR-1 and AGR-2). Herein, we quantify the impact of SiC grain size, irradiation, and temperature on Ag release. In agreement with previous studies, we find accounting for SiC grain size improves agreement between BISON predictions and experimental observations for most cases. In conclusion, we also find that accounting for irradiation improves agreement for cases where Ag release was underestimated, but the impact was less significant than accounting for microstructure.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Effect of Heat Treatment on Microstructure and Mechanical Property of 316L Stainless Steel Produced by Laser Powder Bed Fusion

The advanced non-light water reactor designs (Gen IV reactors), including molten salt/ very high temperature/ sodium-cooled and lead-cooled fast reactors, typically operate at higher temperatures and more extreme radiation conditions than light water reactors. An intrinsic part of the deployment and progress of Gen IV reactor designs is selecting the most suitable structural material for a specific application. Additive manufacturing (AM), a fairly new process of making physical, three-dimensional objects from a computer design file, is going to completely change the way of design, build and certify nuclear systems. It offers a range of opportunities to produce complex geometries from existing materials, offers new routes for processing of previously difficult to process materials, allows for design of new high-performance materials, and finally facilitates hybridization of dissimilar materials. This emerging technology has successfully produced cars, wind turbine blade molds and even live cells. It could also open up big opportunities for the nuclear industry to quickly deploy technologies at a fraction of the cost. So far, AM techniques have been preliminarily applied in the field of nuclear reactors, including the classical parts such as the pressure vessel of a small reactor with 508-III steel, the bottom nozzle of a fuel assembly with 304L steel, the fuel cladding with zirconium alloy and the integrated impeller of a pump and the multi-channel valve body with 316L steel [6,7]. The AM applications for operating nuclear reactors started in auxiliary plant components and have slowly migrated to metallic reactors and core components, but many of these are not safety critical components. Although many parts used for nuclear reactors have been fabricated by AM techniques, practical applications in engineering are still a long way off due to the uncertainty factors focused on the processing, material properties, analysis methods and application standards, which feeds the safety and life-cycle of the nuclear reactor. Due to rapid, repeated heating and cooling during production, a high dislocation density was present in the AM material. This microstructure feature is unstable at elevated temperature while high temperature is one of the typical operation environments for nuclear reactors. Thus, it is important to understand the thermal effect on the microstructure of AM material. The objectives of this study are to investigate the effect of heat treatment on the microstructure and mechanical properties of 316L stainless steel produced by laser powder bed fusion additive manufacturing, and to determine an appropriate heat treatment practice that will be applied to the lightweight AM lattice-structured material with the same chemistry. The heat treatment study consisted of annealing the samples at a temperature range of 800 to 1200 oC with a 50 oC increment for different times (1-24 hours), followed by vacuum or air cooling. Microstructural characterization was carried out by Scanning Electron Microscope (SEM). Grain size and crystallographic orientation were investigated by Electron Backscatter Diffraction (EBSD). Vickers hardness tests with a 0.5 kg load were employed to determine the hardness of samples after different heat treatments. After heat treatment, the random crystallographic orientation was preserved, and the volume fraction of high-angle grain boundaries (grain boundary misorientation =15 oC) remained the same. The dislocation density decreased with annealing temperature due to recovery. The fine subgrain structures in the as-printed specimen were quite stable up to 1200 oC. Minimal recrystallization was observed up to 1200 oC. Recrystallization initiated only after 8.5 hours at 1200 oC. The SEM images did not show obvious dependence of microstructure on cooling rate. The hardness of the specimens decreased with increasing annealing temperature as a result of the decrease in dislocation density. It is interesting to note that the AM material showed very similar hardness to the wrought material when annealing at similar temperature, although the microstructures are very different. Annealing at 1050 oC for 1 hour followed by air cooling was selected as the heat treatment procedure for the lattice designed lightweight AM 316L material.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Physics-based modeling and data analytics [Slides]

This presentation contains a summary of ongoing work within the physics-based modeling and data analytics work package within the Nuclear Materials Discovery and Qualification initiative (NMDQi). Topics include work on MOOSE-based crystal plasticity, molecular dynamics modeling of recombination in metals and alloys, the MOOSE Stochastic Tools Module, and machine learning and atomistic modeling to predict thermo-kinetic properties of nuclear structural materials.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗