Engineering topics
Publications and source records attributed to Kelley, H. L..
Yaw control and overall efficiency increased at hover and low speeds. Wind-tunnel investigation showed strake located on left side of tail boom has potential to reduce high adverse side loads on tail boom in hover and in sideward flight. Test demonstrated addition of single long strake to left side of tail boom most effective configuration for reducing left pedal requirements in right sideward flight.
Aerodynamic characteristics were determined of three cylindrical shapes representative of tail boom cross sections of the U.S. Army AH-64, UH-60, and UH-1H helicopters. Forces and pressures were measured in a wind-tunnel investigation at the Langley Research Center. Data were obtained for a flow incidence range from -45 to 90 deg and a dynamic pressure range from 1.5 to 50 psf. These ranges provided data representative of full-scale Reynolds numbers and the full range of flow incidence to which these helicopter tail boom shapes would be subjected at low flight speeds. The effects of protuberances such as tail rotor drive-shaft covers and spoilers were evaluated. The data indicate that significant side loads on tail booms of helicopters can be generated and that the addition of spoilers can beneficially alter the side loads. Although an increase in vertical drag occurs, the net effect through reduction of tail rotor thrust required can be an improvement in helicopter performance.
Performance of a 27-percent scale model of an advanced rotor designed for the AH-64 helicopter was measured in hover and at forward speeds of 50 to 130 knots. A baseline rotor, modeled after the current AH-64 rotor, was also tested to provide data for comparison. The investigation was conducted to validate procedures used at Langley to design rotors with increased performance potential and to provide a database for evaluation of current and future rotor systems. Both rotors were operated at full-scale tip speeds. Rotor thrust, forward speed, and ground height were varied for each rotor.
A helicopter is disclosed with a system for controlling main-rotor torque which reduces the power and size requirements of conventional anti-torque means. The torque countering forces are generated by disrupting the main rotor downwash flowing around the fuselage. The downwash flow is separated from the fuselage surface by a strake positioned at a specified location on the fuselage. This location is determined by the particular helicopter wash pattern and fuselage configuration, generally being located between 20 deg before top dead center (TDC) and 80 deg from TDC on the fuselage side to which the main rotor blade approaches during rotation. The strake extends along the fuselage from the cabin section to the aft end and can be continuous or separated for aerodynamic surfaces such as a horizontal stabilizer.
Helicopter sling load operations have been limited during pick up and delivery of external cargo by the lack of precision achieved by the combination of pilot, helicopter, and sling load. Use of a closed circuit television as a pilot aid during sling load delivery and placement was documented along with additional cases representing procedures currently employed by military and commercial operators. Although an increase in pilot workload was noted when the television system was used, the results indicated a comparable level of performance for each test case.
Helicopter sling-load operations have been limited during hover and low-speed flight by the degree of precision achieved by the pilot/helicopter/sling-load combination. Previous attempts to improve precision have included stabilization of the load and helicopter and the addition of a pilot station directly facing the load. In these tests, use of a closed-circuit TV as a display that would permit sling-load delivery and placement by the forward-facing pilot was evaluated using a CH-54B helicopter. In all, three test cases were documented, which included the following: (1) forward-facing pilot using the TV display, (2) forward-facing pilot using verbal commands from a load-facing observer, and (3) aft-facing pilot using direct visual cues. The results indicate that a comparable level of performance was achieved for each test case; however, an increase in pilot workload was noted when the TV system was used.
Flight-test results which describe flying-quality factors related to the fan-in-fin yaw control concept as utilized on a pre-production version of a European helicopter are presented. Design compromises to be considered with this concept are also presented. The large, fixed vertical fin associated with the fan-in-fin system was helpful in maneuvering flight, but introduced several flying-quality problems when combined with the fan.
Hovering and low speed flight capabilities of tilt wing VTOL aircraft in terminal area under near-zero visibility instrument landing conditions
Terminal area operations of V/STOL aircraft, considering approaches, approach speeds, wind and velocity effects and noise
VTOL aircraft instrument flight in terminal area, defining requirements and operating characteristics for vertical and low speed capabilities
Flight test evaluation of second generation CL-84 tilt-wing aircraft in hover, transition, and cruise modes
Flight tests with helicopters for studying manueverability
Helicopter rotor blade pressure distributions compared with static two-dimensional airfoil characteristics for extreme flight conditions
Helicopter rotor blade chordwise pressure distribution and two-dimensional airfoil characteristics
Aerodynamic characteristics of a tilt-duct vtol aircraft
Effect of ground proximity, wing-stall phenomena, pitching moments, and power requirements on vtol aircraft
Explore the source record for details and available documents.