Engineering topics

Kelley, Henry L.

Publications and source records attributed to Kelley, Henry L..

18 records

NASA NTRS2000

Exploratory Investigation of Aerodynamic Characteristics of Helicopter Tail Boom Cross-Section Models with Passive Venting

Two large-scale, two-dimensional helicopter tail boom models were used to determine the effects of passive venting on boom down loads and side forces in hovering crosswind conditions. The models were oval shaped and trapezoidal shaped. Completely porous and solid configurations, partial venting in various symmetric and asymmetric configurations, and strakes were tested. Calculations were made to evaluate the trends of venting and strakes on power required when applied to a UH-60 class helicopter. Compared with the UH-60 baseline, passive venting reduced side force but increased down load at flow conditions representing right sideward flight. Selective asymmetric venting resulted in side force benefits close to the fully porous case. Calculated trends on the effects of venting on power required indicated that the high asymmetric oval configuration was the most effective venting configuration for side force reduction, and the high asymmetric with a single strake was the most effective for overall power reduction. Also, curves of side force versus flow angle were noticeable smoother for the vented configurations compared with the solid baseline configuration; this indicated a potential for smoother flight in low-speed crosswind conditions.

Banks, Daniel W.↗

NASA NTRS1995

Variable-Tilt Helicopter Rotor Mast

Variable-tilt helicopter rotor mast proposed to improve helicopter performance and reduce vibration, especially at upper end of forward-speed range of helicopters. Achieved by use of universal coupling in main rotor mast or by tilting entire engine-and-transmission platform. Performance, energy efficiency, and safety enhanced.

Kelley, Henry L.↗

NASA NTRS1995

Exploratory flow visualization investigation of mast-mounted sights in presence of a rotor

A flow visualization investigation with a laser light sheet system was conducted on a 27-percent-scale AH-64 attack helicopter model fitted with two mast-mounted sights in the langley 14- by 22-foot subsonic tunnel. The investigation was conducted to identify aerodynamic phenomena that may have contributed to adverse vibration encountered during full-scale flight of the AH-64D apache/longbow helicopter with an asymmetric mast-mounted sight. Symmetric and asymmetric mast-mounted sights oriented at several skew angles were tested at simulated forward and rearward flight speeds of 30 and 45 knots. A laser light sheet system was used to visualize the flow in planes parallel to and perpendicular to the free-stream flow. Analysis of these flow visualization data identified frequencies of flow patterns in the wake shed from the sight, the streamline angle at the sight, and the location where the shed wake crossed the rotor plane. Differences in wake structure were observed between the sight configurations and various skew angles. Analysis of lateral light sheet plane data implied significant vortex structure in the wake of the asymmetric mast-mounted sight in the configuration that produced maximum in-flight vibration. The data showed no significant vortex structure in the wake of the asymmetric and symmetric configurations that produced no increase in in-flight adverse vibration.

Ghee, Terence A.↗

NASA NTRS1994

Further Research On Helicopter Tail-Boom Strakes

Two documents discuss results of additional investigations of concept introduced in "Helicopter Tail-Boom Strakes" (LAR-13233). Essence of concept that strake or pair of strakes on side of tail boom facing retreating side of main rotor of helicopter perturbs flow in such way to increase aerodynamic pressure on that side, contributing force to thrust from tail rotor. Because of force, thrust required of tail rotor for yaw control reduced. Important advantage in low-speed flight, especially in sideward flight, in which tail-rotor thrust in absence of strake sometimes insufficient.

Kelley, Henry L.↗

NASA NTRS1993

Process for bonding elastomers to metals

A process for bonding elastomeric material to a metal part includes coating a heat curable adhesive on the surfaces of the metal part to be bonded. The metal part is placed in a mold, a bottom plate and an upper transfer pot of a transfer molding machine is preheated to a predetermined cure temperature. A predetermined quantity of uncured elastomeric material is loaded into the transfer pot. The mold containing the adhesive coated metal part is clamped to the bottom plate, and almost contemporaneously, the uncured elastomeric material is pressed into the mold while maintaining heat and pressure in the mold for a time sufficient to vulcanize and thereby cure the elastomeric material simultaneously with the adhesive, whereby contacting surfaces of the metal part are strongly bonded to the vulcanized elastomeric material.

Dickerson, George E.↗

NASA NTRS1993

Helicopter low-speed yaw control

A system for improving yaw control at low speeds consists of one strake placed on the upper portion of the fuselage facing the retreating rotor blade and another strake placed on the lower portion of the fuselage facing the advancing rotor blade. These strakes spoil the airflow on the helicopter tail boom during hover, low speed flight, and right or left sidewards flight so that less side thrust is required from the tail rotor.

Wilson, John C.↗

NASA NTRS1993

The strake - A simple means for directional control improvement

On the basis of several flight test programs conducted to date, a directional control margin improvement of at least 5 percent is obtainable for right-sideward flight throught the use of flow pattern separation-controlling tail-boom strakes. The enhanced directional control margin is critically important in low speed maneuvers, where high airloads are experienced by the tailboom. Numerous European helicopters have incorporated the strake on their tailbooms.

Wilson, John C.↗

NASA NTRS1993

Flow visualization of mast-mounted-sight/main rotor aerodynamic interactions

Flow visualization tests were conducted on a 27 percent-scale AH-64 attack helicopter model fitted with various mast-mounted-sight configurations in an attempt to identify the cause of adverse vibration encountered during full-scale flight tests of an Apache/Longbow configuration. The tests were conducted at the NASA Langley Research Center in the 14- by 22-Foot Subsonic Tunnel. A symmetric and an asymmetric mast-mounted-sight oriented at several skew angles were tested at forward and rearward flight speeds of 30 and 45 knots. A laser light sheet seeded with vaporized propylene glycol was used to visualize the wake of the sight in planes parallel and perpendicular to the freestream flow. Analysis of the flow visualization data identified the frequency of the wake shed from the sight, the angle-of-attack at the sight, and the location where the sight wake crossed the rotor plane. Differences in wake structure were observed between the various sight configurations and slew angles. Postulations into the cause of the adverse vibration found in flight test are given along with considerations for future tests.

Ghee, Terence A.↗

NASA NTRS1992

Enhancing Control Of Helicopter Yaw At Low Speed

Spoilers on tail boom significantly improve yaw control in both right and left sidewinds. Spoilers are two thin plates extending outward, perpendicular to curvature of boom, distance of about 6 percent of total depth of tail boom. Along-the-boom dimensions of spoilers are as long as possible without interfering with such existing critical parts as tail rotor. Further enhancement, spoilers made retractable and automatically deployable as required. Concept applicable to all single-rotor helicopters. Applied as simple economical addition to existing helicopters or incorporated into new helicopter designs.

Kelley, Henry L.↗

NASA NTRS1992

Two-dimensional aerodynamic characteristics of several polygon-shaped cross-sectional models applicable to helicopter fuselages

A wind-tunnel investigation was conducted to determine 2-D aerodynamic characteristics of nine polygon-shaped models applicable to helicopter fuselages. The models varied from 1/2 to 1/5 scale and were nominally triangular, diamond, and rectangular in shape. Side force and normal force were obtained at increments of angle of flow incidence from -45 to 90 degrees. The data were compared with results from a baseline UH-60 tail-boom cross-section model. The results indicate that the overall shapes of the plots of normal force and side force were similar to the characteristic shape of the baseline data; however, there were important differences in magnitude. At a flow incidence of 0 degrees, larger values of normal force for the polygon models indicate an increase in fuselage down load of 1 to 2.5 percent of main-rotor thrust compared with the baseline value. Also, potential was indicated among some of the configurations to produce high fuselage side forces and yawing moments compared with the baseline model.

Kelley, Henry L.↗

NASA NTRS1990

Aerodynamic Effect of Strakes on Two-Dimensional Tail Boom Models of the OH-58A and the OH-58D Helicopters

During hover and low speed flight, helicopters experience significant aerodynamic forces on the tail boom caused by the wake from the main and tail rotors and by crosswinds. These effects were simulated during a study conducted in the Langley 14 by 22 Foot Subsonic Tunnel on a 136 percent scaled 2-D tail boom model with cross sections representative of those on the U.S. Army OH-58A and the OH-58D helicopters. The effects of longitudinal strakes attached to the cross sections were studied. To obtain the aerodynamic forces acting on the cross sections, the flow incidence range on the scaled models was varied from -45 to 90 degrees and the models were tested through a dynamic pressure range of 5 to 15 psf. The results of the OH-58A and the OH-58D configurations show a significant improvement at conditions which represent right sideward flight by reducing the adverse aerodynamic side force when the strakes are installed. These data were used to calculate a change in tail rotor power for the full scale flight vehicle and indicated approx. a 5 to 6 percent average savings in right sideward flight for the critical velocity range of 0 to 30 knots. Increases in the tail boom normal force were noted due to the strakes. The results indicate a potential for reducing the directional control and tail rotor thrust required in the critical hover and right sideward flight speed range with a calculated minimum increase to main rotor power required and an overall net improvement in power of 0.5 percent for both the OH-58A and OH-58D.

Crowell, Cynthia A.↗

NASA NTRS1990

Bonding Elastomers To Metal Substrates

Improved, economical method for bonding elastomers to metals prevents failures caused by debonding. In new technique, vulcanization and curing occur simultaneously in specially designed mold that acts as form for desired shape of elastomer and as container that positions and supports metal parts. Increases interface adhesion between metal, adhesive, and elastomer.

Dickerson, George E.↗

NASA NTRS1990

Aerodynamic Performance of a 0.27-Scale Model of an AH-64 Helicopter with Baseline and Alternate Rotor Blade Sets

Performance of a 27 percent scale model rotor designed for the AH-64 helicopter (alternate rotor) was measured in hover and forward flight and compared against and AH-64 baseline rotor model. Thrust, rotor tip Mach number, advance ratio, and ground proximity were varied. In hover, at a nominal thrust coefficient of 0.0064, the power savings was about 6.4 percent for the alternate rotor compared to the baseline. The corresponding thrust increase at this condition was approx. 4.5 percent which represents an equivalent full scale increase in lift capability of about 660 lbs. Comparable results were noted in forward flight except for the high thrust, high speed cases investigated where the baseline rotor was slightly superior. Reduced performance at the higher thrusts and speeds was likely due to Reynolds number effects and blade elasticity differences.

Kelley, Henry L.↗

NASA NTRS1990

Flight investigation of the effect of tail boom strakes on helicopter directional control

A joint U.S. Army/NASA flight investigation was conducted utilizing an instrumented Bell 240B single-rotor helicopter to determine the effectiveness of horizontally-mounted tail boom strakes on directional controllability and tail rotor power required during low-speed, crosswind operating conditions. The purpose of the strakes was to separate airflow over the tail boom and change fuselage yawing moments in a direction to improve the yaw control margin and reduce tail rotor power required. Low-speed crosswind data were obtained in 5-knot increments at airspeeds of 0 knots to 35 knots and for 30 deg increments in wind azimuth from 0 to 330 deg. In right sideward flight at the most critical wind azimuth and airspeed (60 deg azimuth measured from the nose of the aircraft and 20 knots airspeed), the strakes improved the pedal margin by about 6 percent of total travel and reduced the tail rotor power required by 17 percent. The increase in yaw control and reduction in tail rotor power offered by the strakes can expand the operating envelope in terms of gross weight and altitude capability. No effects in forward flight were noted.

Kelley, Henry L.↗

NASA NTRS1988

Development in helicopter tail boom strake applications in the US

The use of a strake or spoiler on a helicopter tail boom to beneficially change helicopter tail boom air loads was suggested in the United States in 1975. The anticipated benefits were a change of tail boom loads to reduce required tail rotor thrust and power and improve directional control. High tail boom air loads experienced by the YAH-64 and described in 1978 led to a wind tunnel investigation of the usefullness of strakes in altering such loads on the AH-64, UH-60, and UH-1 helicopters. The wind tunnel tests of 2-D cross sections of the tail boom of each demonstrated that a strake or strakes would be effective. Several limited test programs with the U.S. Army's OH-58A, AH-64, and UH-60A were conducted which showed the effects of strakes were modest for those helicopters. The most recent flight test program, with a Bell 204B, disclosed that for the 204B the tail boom strake or strakes would provide more than a modest improvement in directional control and reduction in tail rotor power.

Wilson, John C.↗

NASA NTRS1987

Helicopter anti-torque system using fuselage strakes

The improvement of the helicopter torque control system is discussed. At low to medium forward speeds helicopter performance is limited by the effectiveness of the means for counteracting main rotor torque and controlling sideslip airloads. These problems may be overcome by mounting strakes on the aft fuselage section. For single rotor helicopters whose main rotor rotates counter-clockwise as viewed from above, one of the strakes would be mounted in the upper lefthand quadrant and the second in the lower left hand quadrant. The strakes alter the air flow around the fuselage by separating the flow so as to produce lateral airloads on the tail boom which oppose main-rotor torque. The upper strake operates in a right crosswind to oppose main rotor torque, and the lower strake has effect in left crosswinds. The novelty of this invention resides in the simple and economical manner in which the helicopter tail boom may be modified by the addition of strakes in order to increase torque control, and reduce the need for supplemental mechanical means of torque control.

Kelley, Henry L.↗

NASA NTRS1987

Effect of planform taper on hover performance of an advanced AH-64 model rotor

The hover performance of a 27 percent scale model baseline rotor and advanced rotor with a 3:1 tapered tip (TR3) for the AH-64 attack helicopter was investigated and compared. Hover results from a previously tested advanced rotor with a 5:1 tapered tip (TR5) were also compared. Rotor thrust was varied over a range for two tip Mach numbers. The results indicated that the TR3 blades had improved performance compared with the TR5 blades, and both the TR3 and TR5 blades were superior to the baseline rotor. The additional margin in performance for the TR3 blades was likely due to an increase in blade area and Reynolds number in the tip region of the blades.

Kelley, Henry L.↗

NASA NTRS1960

A Flight Study of the Conversion Maneuver of a Tilt-Duct VTOL Aircraft

Flight records are presented from an early flight test of a wing-tip mounted tilting-ducted-fan, vertical-take-off and landing (VTOL) aircraft configuration. Time histories of the aircraft motions, control positions, and duct pitching-moment variation are presented to illustrate the characteristics of the aircraft in hovering, in conversion from hovering to forward flight, and in conversion from forward flight to hovering. The results indicate that during essentially continuous slow level- flight conversions, this aircraft experiences excessive longitudinal trim changes. Studies have shown that the large trim changes are caused primarily by the variation of aerodynamic moments acting on the duct units. Action of the duct-induced downwash on the horizontal stabilizer during the conversion also contributes to the longitudinal trim variations. Time histories of hovering and slow vertical descent in the final stages of landing in calm air show angular motions of the aircraft as great as +/- 10 deg. about all axes. Stick and pedal displacements required to control the aircraft during the landing maneuver were on the order of 50 to 60 percent of the total travel available.

Tapscott, Robert J.↗