Engineering topics

Kelly, R. E.

Publications and source records attributed to Kelly, R. E..

8 records

NASA NTRS2007

Seasonal Snow Extent and Snow Mass in South America Using SMMR and SSM/I Passive Microwave Data (1979-2003)

Seasonal snow cover in South America was examined in this study using passive microwave satellite data from the Scanning Multichannel Microwave Radiometer (SMMR) on board the Nimbus-satellite and the Special Sensor Microwave Imagers (SSM/I) on board Defense Meteorological Satellite Program (DMSP) satellites. For the period from 1979-2003, both snow cover extent and snow depth (snow mass) were investigated during coldest months (May-September), primarily in the Patagonia area of Argentina and in Chile. Most of the seasonal snow in South America is in the Patagonia region of Argentina. Since winter temperatures in this region are often above freezing, the coldest winter month was found to be the month having the most extensive snow cover and also usually the month having the deepest snow cover as well. Sharp year-to-year differences were recorded using the passive microwave observations. The average snow cover extent for July, the month with the greatest average snow extent during the 25-year period of record, is 320,700 km(exp 2). In July of 1984, the average monthly snow cover was 701,250 km(exp 2) - the most extensive coverage observed between 1979 and 2003. However, in July of 1989, snow cover extent was only 120 km(exp 2). The 25-year period of record shows a sinusoidal like pattern, though there appears to be no obvious trend in either increasing or decreasing snow extent or snow mass between 1979 and 2003.

Foster, J. L.↗

NASA NTRS1999

Studies in Thermocapillary Convection of the Marangoni-Benard Type

A nonlinear feedback control strategy for delaying the onset and eliminating the subcritical nature of long-wavelength Marangoni-Benard convection is investigated based on an evolution equation. A control temperature is applied to the lower wall in a gas-liquid layer otherwise heated uniformly from below. It is shown that, if the interface deflection is assumed to be known via sensing as a function of both horizontal coordinates and time, a control temperature with a cubic-order polynomial dependence on the deflection is capable of delaying the onset as well as eliminating the subcritical instability altogether, at least on the basis of a weakly nonlinear analysis. The control coefficients required for stabilization are O(1) for both delaying onset indefinitely and eliminating subcritical instability.

Kelly, R. E.↗

NASA NTRS1994

Effect of density gradients in confined supersonic shear layers, part 1

The effect of density gradients on the supersonic wall modes (acoustic modes) of a 2-D confined compressible shear layer were investigated using linear analysis. Due to the inadequacies of the hyperbolic tangent profile, the boundary layer basic profiles were used. First a test case was taken with the same parameters as in Tam and Hu's analysis with convective Mach number M(sub c) = 1.836 and density ratio of 1.398. Three generalized inflection points were found giving rise to three modes. The first two show similar properties to the Class A and B modes, and the third is an 'inner mode' which will be called a Class C mode. As the density ratio is increased, the smallest of the three neutral phase speeds tends towards the speed of the lower velocity stream, and the other two eventually coalesce and then disappear. These two effects lead to a linear resonance between the Class B modes which increases the cutoff frequency and growth rate of the lowest mode. In fact, growth rates of 2-4 times the test case were found as the density ratio was increased to 7. A similar trend is observed for the Class A modes when the density ratio is decreased from the test case, but the growth rate is not changed by much from the test case.

Peroomian, Oshin↗

NASA NTRS1994

Effect of density gradients in confined supersonic shear layers. Part 2: 3-D modes

The effect of basic flow density gradients on the supersonic wall modes were investigated in Part 1 of this analysis. In that investigation only the 2-D modes were studied. Tam and Hu investigated the 3-D modes in a confined vortex sheet and reported that the first 2-D Class A mode (A01) had the highest growth rate compared to all other 2-D and 3-D modes present in the vortex sheet for that particular set of flow patterns. They also showed that this result also held true for finite thickness shear layers with delta(sub w) less than 0.125. For free shear layers, Sandham and Reynolds showed that the 3-D K-H mode became the dominant mode for M(sub c) greater than 0.6. Jackson and Grosch investigated the effect of crossflow and obliqueness on the slow and fast odes present in a M(sub c) greater than 1 environment and showed that for certain combination of crossflow and wave angles the growth rates could be increased by up to a factor of 2 with respect to the 2-D case. The case studied here is a confined shear layer shown in Part 1. All solution procedures and basic low profiles are the same as in Part 1. The effect of density gradients on the 3-D modes present in the density ratios considered in Part 1 are investigated.

Peroomian, Oshin↗

NASA NTRS1992

The instability of a liquid jet in a compressible airstream

The instability of a liquid jet immersed in a coflowing compressible airstream is investigated, for both two-dimensional and circular jets, using a simplified flow model in which the effects associated with the cross-flow component of velocity are ignored. Results of the analysis agreed qualitatively with experimental results in that they suggest a more violent instability when the free-stream Mach number is close to unity. It was also found that a change from convective to absolute instability occurs in this transonic flow regime.

Li, H.-S.↗

NASA NTRS1986

Space Shuttle Orbiter - Leading edge structural design/analysis and material allowables

Reinforced Carbon-Carbon (RCC), a structural composite whose development was targeted for the high temperature reentry environments of reusable space vehicles, has successfully demonstrated that capability on the Space Shuttle Orbiter. Unique mechanical properties, particularly at elevated temperatures up to 3000 F, make this material ideally suited for the 'hot' regions of multimission space vehicles. Design allowable characterization testing, full-scale development and qualification testing, and structural analysis techniques will be presented herein that briefly chart the history of the RCC material from infancy to eventual multimission certification for the Orbiter. Included are discussions pertaining to the development of the design allowable data base, manipulation of the test data into usable forms, and the analytical verification process.

Johnson, D. W.↗

NASA NTRS1983

Space shuttle orbiter leading-edge flight performance compared to design goals

Thermo-structural performance of the Space Shuttle orbiter Columbia's leading-edge structural subsystem for the first five (5) flights is compared with the design goals. Lessons learned from thse initial flights of the first reusable manned spacecraft are discussed in order to assess design maturity, deficiencies, and modifications required to rectify the design deficiencies. Flight data and post-flight inspections support the conclusion that the leading-edge structural subsystem hardware performance was outstanding for the initial five (5) flights.

Curry, D. M.↗

NASA NTRS1968

Development of biaxial test fixture includes cryogenic application

Test fixture has the capability of producing biaxial stress fields in test specimens to the point of failure. It determines biaxial stress by dividing the applied load by the net cross section. With modification it can evaluate materials, design concepts, and production hardware at cryogenic temperatures.

Helf, J. C.↗