Search NASA⌕ Search

Engineering topics

Kennedy, F. E., Jr.

Publications and source records attributed to Kennedy, F. E., Jr..

7 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Plasticity analysis of wear phenomena as an aid in the development of abradable materials

Plastic deformation accompanying the wear process in fully dense and porous metals was studied in order to develop more abradable gas path seal material systems for turbine engine applications. The finite element method was used to model high-rate viscoplastic deformation in the vicinity of a moving contact. Techniques were developed for studying such deformation in both solid (fully dense) and porous metals. Results of the analysis were verified by comparison with experimental data obtained using a pendulum-type rub test apparatus and a pin-on-disk sliding wear tester. It was found that the near-surface plastic deformation in fully dense solids was different from that for porous materials because of the compressibility of the latter. Both types of materials exhibit deformation features which can be taken advantage of in the design of more abradable material systems.

Kennedy, F. E., Jr.↗
NASA NTRS1984

Thermal and thermomechanical effects in dry sliding

Developments in the study of interrelated thermal and mechanical phenomena in sliding systems are reviewed. The topics reviewed include mechanisms of frictional heating and the distribution of heat during sliding friction, the experimental measurement and analysis of surface and near-surface temperatures resulting from frictional heating, thermal deformation around sliding contacts and the changes in contact geometry caused by thermal deformation and thermoelastic instability, and the thermomechanical stress distribution around the frictionally heated and thermally deformed contact spots. The influence of the thermal and thermomechanical contact phenomena on friction and wear, surface melting, softening, chemical deterioration, and thermocracking are discussed. The phenomena have important implications in the design and application of sliding or sliding-rolling mechanical components such as dynamic seals, brakes, clutches, plastic bearings, solid or boundary-lubricated bearings, and gears.

Kennedy, F. E., Jr.↗
NASA NTRS1984

Determination of near-surface plastic deformation in sliding contacts

It is pointed out that substantial plastic deformation occurs on and near the contact surfaces, when two solid bodies slide against each other without lubrication. It has been found that this deformation plays an important role in the tribological behavior of the sliding contact. The present investigation has the objective to develop an analytical model to predict the near-surface plastic deformation resulting from a single pass of one metallic surface over another. A finite element viscoplasticity program was written relating velocities to forces in a two-dimensional domain. The program was employed in the study of plastic deformation during a single pass of a hardened tool steel slider over a copper rub specimen. It was found that essentially the only material set in motion by the slider was directly under the contact zone. The agreement between values obtained in the analysis and experimental data is reasonably good.

Kennedy, F. E., Jr.↗
NASA NTRS1980

Surface temperatures in sliding systems - A finite element analysis

Finite element equations are developed for studying surface temperatures resulting from frictional heating in sliding systems. The equations include the effect of velocity of moving components, an effect which is found to be quite significant, even at low sliding velocities. A program was written using the equations and it was applied to the study of surface temperatures in two different sliding systems: dry or boundary lubricated sleeve bearings and a labyrinth gas path seal configuration. Very good agreement was achieved between analytical predictions using the program and experimental temperature measurements. The program was used to study the influence of various material parameters on surface temperatures in the two sliding systems.

Kennedy, F. E., Jr.↗
NASA NTRS1974

A thermal, thermoelastic, and wear analysis of high-energy disk brakes

A thermomechanical investigation of the sliding contact problem encountered in high-energy disk brakes is described. The analysis includes a modelling, using the finite element method of the thermoelastic instabilities that cause transient changes in contact area to occur on the friction surface. In order to include the effect of wear at the contact surface, a wear criterion is proposed that results in the prediction of wear rates for disk brakes that are quite close to experimentally determined wear rates. The thermal analysis shows that the transient temperature distribution in a disk brake assembly can be determined more accurately by use of this thermomechanical analysis than by a more conventional analysis that assumes constant contact conditions. It also shows that lower, more desirable, temperatures in disk brakes can be attained by increasing the volume, the thermal conductivity, and, especially, the heat capacity of the brake components.

Kennedy, F. E., Jr.↗
NASA NTRS1973

A thermal, thermoelastic, and wear simulation of a high-energy sliding contact problem

This paper describes an investigation of the sliding contact problem encountered in high-energy disk brakes. The analysis includes a simulation modeling, using the finite element method, of the thermoelastic instabilities that cause transient changes in contact to occur on the friction surface. In order to include the effect of wear of the concentrated contacts on the friction surface, a wear criterion is proposed that results in prediction of wear rates for disk brakes that are quite close to experimentally determined wear rates. The thermal analysis shows that the transient temperature distribution in a disk brake can be determined more accurately by use of this thermomechanical analysis than by a more conventional analysis that assumes constant contact conditions. It is also shown that lower, more desirable, temperatures in disk brakes can be attained by increasing the volume, the thermal conductivity, and especially, the heat capacity of the brake components.

Kennedy, F. E., Jr.↗