Engineering topics

Kenny, Barbara

Publications and source records attributed to Kenny, Barbara.

5 records

DOE OSTI2024

2023 Peer Review Final Report

The U.S. Department of Energy’s Office of Energy Efficiency and Renewable Energy requires each of its programs to conduct periodic peer reviews to enhance EERE program planning. May 16–18, 2023, the Advanced Materials and Manufacturing Technologies Office (AMMTO) held an in-person peer review of its program activities in which an independent panel of experts provided AMMTO with feedback on how well the new office’s programs align with its overarching goals and mission statement, identified possible course correction, and shared information. This review marks AMMTO’s first in-person peer review since the Advanced Manufacturing Office evolved into AMMTO and the Industrial Decarbonization and Efficiency Office. A detailed summary of observations, findings, impact, and recommendations is contained in the following report.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

NASA NTRS2005

Single Axis Flywheel IPACS @1300W, 0.8 N-m

NASA Glenn Research Center is developing flywheels for space systems. A single axis laboratory version of an integrated power and attitude control (IPACs) system has been experimentally demonstrated. This is a significant step on the road to a flight qualified three axes IPACS system. The presentation outlines the flywheel development process at NASA GRC, the experimental hardware and approach, the IPACS control algorithm that was formulated and the results of the test program and then proposes a direction for future work. GRC has made progress on flywheel module design in terms of specific energy density and capability through a design and test program resulting in three flywheel module designs. Two of the flywheels are used in the 1D-IPACS experiment with loads and power sources to simulate a satellite power system. The system response is measured in three power modes: charge, discharge, and charge reduction while simultaneously producing a net output torque which could be used for attitude control. Finally, recommendations are made for steps that should be taken to evolve from this laboratory demonstration to a flight like system.

Jansen, Ralph↗

NASA NTRS2003

Motor Control and Regulation for a Flywheel Energy Storage System

This talk will focus on the motor control algorithms used to regulate the flywheel system at the NASA Glenn Research Center. First a discussion of the inner loop torque control technique will be given. It is based on the principle of field orientation and is implemented without a position or speed sensor (sensorless control). Then the outer loop charge and discharge algorithm will be presented. This algorithm controls the acceleration of the flywheel during charging and the deceleration while discharging. The algorithm also allows the flywheel system to regulate the DC bus voltage during the discharge cycle.

Kenny, Barbara↗

NASA NTRS2002

Single Axis Attitude Control and DC Bus Regulation with Two Flywheels

A computer simulation of a flywheel energy storage single axis attitude control system is described. The simulation models hardware which will be experimentally tested in the future. This hardware consists of two counter rotating flywheels mounted to an air table. The air table allows one axis of rotational motion. An inertia DC bus coordinator is set forth that allows the two control problems, bus regulation and attitude control, to be separated. Simulation results are presented with a previously derived flywheel bus regulator and a simple PID attitude controller.

Kascak, Peter E.↗

NASA NTRS1990

Control of multiple resonant power processors in a multi-source system

Analysis and test results show that phasor-regulated, Mapham-derived resonant inverters can be paralleled to provide standardizing interfaces for multiple sources on a utility-type, aerospace power distribution bus. The basic sources do not require matching in any way, and may have grossly different characteristics. Fully stable system architectures with multiple sources, parallel/redundant distribution buses, and a wide variety of loads can be easily constructed and controlled. The commands and parameters available for system control allow for tight tolerance bus voltage control, and absolute power-sharing control from the various sources over the full range of possible source and load variations. That level of control enables simplified load power processing hardware and the distribution of losses to optimally load the source thermal control system. Positive control of all system performance and allocation of losses are not required by all missions or vehicles, and overall vehicle considerations do not always require the loads on vehicle energy sources and thermal control systems to be balanced. In those cases, power system control can be simplified, and a hierarchical set of defaults can be substituted for computer-generated or supervisory input commands to allow for stable, fully autonomous system operation.

Mildice, James↗