Engineering topics
Publications and source records attributed to Kerwin, E. M..
The use of low-earth-orbit microwave transmission systems to transfer power between two co-orbiting satellites is investigated. A microwave system with a 20 m antenna and 30 m rectenna over a 5-10 km operating range could have possible applications for transmitting 100 kW of power. Antenna/rectenna trade-off sizings, taper analyses, orbital considerations, and possible uses are discussed.
A comparison is made between projected electricity costs of an optimized space solar power station (SPS) in GEO and a moon-based SPS (LPS). A single SPS would receive sunlight on an almost uninterruptible basis. The LPS would be illumined 50 percent of the time, thus requiring two stations on opposite sides of the moon as well as three terrestrial rectennas spaced 120 deg apart. The 5 percent efficient LPS cells would be manufactured from lunar materials and built into arrays mounted on tall mounds. The steerable GEO SPS would have 15 percent efficient cells. Construction costs would be significantly lower on the moon, but the total antenna area would need to be two orders of magnitude larger to produce the same output as the SPS. It is estimated that the LPS would therefore deliver 5 GW electricity to earth stations at a cost of 511.3 mills/kW, compared to 46.8 mills/kW from the SPS. It is concluded that lunar materials are suitable for building an SPS, not a LPS.
An optimization technique for generating antenna illumination tapers allows improved microwave transmission efficiencies from proposed solar power satellite (SPS) systems and minimizes sidelobe levels to meet preset environmental standards. The cumulative microwave power density levels from 50 optimized SPS systems are calculated at the centroids of each of the 3073 counties in the continental United States. These cumulative levels are compared with Environmental Protection Agency (EPA) measured levels of electromagnetic radiation in seven eastern cities. Effects of rectenna relocations upon the power levels/population exposure rates are also studied.
The object of this investigation is to determine the grating lobe characteristics for the SPS (solar power satellite) microwave power beam. Using techniques of Fourier array decomposition, equations, and numerical results are given for the complete SPS microwave antenna pattern (main beam plus grating lobes). In order to ensure the grating lobe peaks are below the environmental guideline of 0.01 mW/sq cm, constraints are defined for the mechanical alignment (tilt) of the SPS antenna and the satellite attitude control system. Two conditions, phase control to the subarray level and to the power module (tube) level, are analyzed as to their effects upon grating lobes.
A generalized antenna design technique is applied to the unique environmental requirements pertaining to solar power satellite (SPS) systems. Optimal illumination tapers and antenna/rectenna sizings are generated which allow increased transmit powers and lower electricity costs while minimizing sidelobe levels to meet a 0.01 mW/sq cm environmental standard. These optimal tapers also provide other advantages over the 10 dB Gaussian reference system.
An antenna optimization technique is applied to the environmental requirements pertaining to SPS (solar power satellite) systems to create high efficiency, multiple beams from a single antenna. Effects of rectenna spacings, subarray sizing, multiple beam degradations, antenna electrical and mechanical errors, and satellite motion are investigated. Advantages of multiple beam SPS systems include operational flexibility, lower power per rectenna, fewer satellites, smaller rectennas, and adherence to a 0.01 mW/sq cm environmental guidelines for sidelobe levels. These advantages suggest multiple beam systems are attractive alternatives to the present single beam system.
The sizing, criteria, cost analysis, and optimized taper of the Solar Power Satellite (SPS) transmitting antenna are discussed. The sizing parameters considered were a thermal limit of 23 kW/sq m in the antenna, a peak power density of 23 mW/sq cm in the ionosphere, and cost effectiveness. Cost schedules and equations are presented for the SPS, and four antenna tapers are analyzed and compared, including the reference 10 dB Gaussian taper. An even powered quadratic series is formulated to minimize electricity cost and stay within thermal and ionospheric power level limits. The optimized Johnson Space Center taper is found to display the lowest energy costs, 4% below the 10 dB Gaussian, and can deliver 5.69 GW at 45.4 mills/kWh to the grid. Further studies are indicated for the optimal antenna and rectenna sizes