Engineering topics

Kessler, W. C.

Publications and source records attributed to Kessler, W. C..

5 records

NASA NTRS1975

Test evaluation of potential heat shield contamination of an Outer Planet Probe's atmospheric sampling system

An Outer Planets Probe which retains the charred heatshield during atmospheric descent must deploy a sampling tube through the heatshield to extract atmospheric samples for analysis. Once the sampling tube is deployed, the atmospheric samples ingested must be free of contaminant gases generated by the heatshield. Outgassing products such as methane and water vapor are present in planetary atmospheres and hence, ingestion of such species would result in gas analyzer measurement uncertainties. This paper evaluates the potential for, and design impact of, the extracted atmospheric samples being contaminated by heatshield outgassing products. Flight trajectory data for Jupiter, Saturn and Uranus entries are analyzed to define the conditions resulting in the greatest potential for outgassing products being ingested into the probe's sampling system. An experimental program is defined and described which simulates the key flow field features for a planetary flight in a ground-based test facility. The primary parameters varied in the test include: sampling tube length, injectant mass flow rate and angle of attack. Measured contaminant levels predict the critical sampling tube length for contamination avoidance. Thus, the study demonstrates the compatibility of a retained heatshield concept and high quality atmospheric trace species measurements.

Kessler, W. C.↗

NASA NTRS1975

Test evaluation of potential heatshield contamination of an outer planet probe's gas sampling system

The feasibility of retaining the heat shield for outer planet probes was investigated as a potential source of atmospheric sample contamination by outgassing. The onboard instruments which are affected by the concept are the pressure sensor, temperature sensor, IR detector, nephelometer, and gas sampling instruments. It was found that: (1) The retention of the charred heatshield and the baseline atmospheric sampling concepts are compatible with obtaining noncontaminated atmospheric samples. (2) Increasing the sampling tube length so that it extends beyond the viscous boundary layer eliminates contamination of the atmospheric sample. (3) The potential for contamination increases with angle of attack.

Kessler, W. C.↗

NASA NTRS1974

Impact of the retained heat shield concept on science instruments

Associated interface problems between the mass spectrometer and the actual probe design are considered along with the problem of producing a clean sample to the gas detection instrument. Of particular interest is the penetration of the heat shield by the mass spectrometer sampling tube, because it must be demonstrated that the sampling tube can penetrate the heat shield and that the mass spectrometer can be supplied with a contaminant-free gas sample, free of contaminants from out-gassing of the heat shield.

Kessler, W. C.↗

NASA NTRS1972

Aerothermodynamic measurements for space shuttle configuration in hypersonic wind tunnels

The effect of shuttle configuration geometry, angle of attack, and free stream flow conditions on the heat-transfer distribution as influenced by three-dimensional effects, the wing-fuselage shock-interaction, and resultant wing-impingement phenomena are examined. In addition, the data provided information regarding the flow field in the vicinity of the nose and boundary layer transition in the plane of symmetry of the fuselage. The data included measurements of the surface pressure, the heat transfer rate distributions, (using models instrumented with thermocouples and models painted with thermographic phosphor) and schlieren and shadowgraph photographs. Posttest photographs of the painted models supplemented the heat transfer data.

Bertin, J. J.↗

NASA NTRS1971

Hypersonic shock wave interaction and impingement

An experimental investigation was conducted on space shuttle type, body-wing configurations. The purpose of the investigation was to determine the effects of body and wing geometry on the hypersonic shock structure about these vehicles and on the resulting surface impingement of interior flow field shock and expansion waves. Schlieren photographs and thermographic phosphor paint data were obtained on three body cross sections with three wing planforms at 40, 50 and 60 degree angles of attack. Specific configuration data were obtained at 0 and 30 degree angles of attack to develop trends. These data were obtained at a nominal Mach number of 13.5 and a freestream unit Reynolds number of 0.7 million per foot. For comparison with these straight wing configurations, data were also obtained on a model of a point design, high cross-range, delta wing orbiter at 40, 50 and 60 degree angles of attack. As expected, the data on this delta wing orbiter indicated that the shock intersection/impingement phenomena associated with straight wing vehicles are considerably more complex than, and result in both windward and leeward surface heating regions not present on, the delta configuration.

Kessler, W. C.↗