Engineering topics

Key, David L.

Publications and source records attributed to Key, David L..

8 records

NASA NTRS2002

Piloted Simulator Investigation of Techniques to Achieve Attitude Command Response with Limited Authority Servos

The purpose of the study was to develop generic design principles for obtaining attitude command response in moderate to aggressive maneuvers without increasing SCAS series servo authority from the existing +/- 10%. In particular, to develop a scheme that would work on the UH-60 helicopter so that it can be considered for incorporation in future upgrades. The basic math model was a UH-60A version of GENHEL. The simulation facility was the NASA-Ames Vertical Motion Simulator (VMS). Evaluation tasks were Hover, Acceleration-Deceleration, and Sidestep, as defined in ADS-33D-PRF for Degraded Visual Environment (DVE). The DVE was adjusted to provide a Usable Cue Environment (UCE) equal to two. The basic concept investigated was the extent to which the limited attitude command authority achievable by the series servo could be supplemented by a 10%/sec trim servo. The architecture used provided angular rate feedback to only the series servo, shared the attitude feedback between the series and trim servos, and when the series servo approached saturation the attitude feedback was slowly phased out. Results show that modest use of the trim servo does improve pilot ratings, especially in and around hover. This improvement can be achieved with little degradation in response predictability during moderately aggressive maneuvers.

Key, David L.↗

NASA NTRS2002

Airworthiness Qualification Criteria for Rotorcraft with External Sling Loads

This report presents the results of a study to develop airworthiness requirements for rotorcraft with external sling loads. The report starts with a review of the various phenomena that limit external sling load operations. Specifically discussed are the rotorcraft-load aeroservoelastic stability, load-on handling qualities, effects of automatic flight control system failure, load suspension system failure, and load stability at speed. Based on past experience and treatment of these phenomena, criteria are proposed to form a package for airworthiness qualification. The desired end objective is a set of operational flight envelopes for the rotorcraft with intended loads that can be provided to the user to guide operations in the field. The specific criteria proposed are parts of ADS-33E-PRF; MIL-F-9490D, and MIL-STD-913A all applied in the context of external sling loads. The study was performed for the Directorate of Engineering, U.S. Army Aviation and Missile Command (AMCOM), as part of the contract monitored by the Aerothermodynamics Directorate, U.S. Army AMCOM.

Key, David L.↗

NASA NTRS1993

Some lessons learned in three years with ADS-33C

Three years of using the U.S. Army's rotorcraft handling qualities specification, Aeronautical Design Standard - 33, has shown it to be surprisingly robust. It appears to provide an excellent basis for design and for assessment, however, as the subtleties become more well understood, several areas needing refinement became apparent. Three responses to these needs have been documented in this paper: (1) The yaw-axis attitude quickness for hover target acquisition and tracking can be relaxed slightly. (2) Understanding and application of criteria for degraded visual environments needed elaboration. This and some guidelines for testing to obtain visual cue ratings have been documented. (3) The flight test maneuvers were an innovation that turned out to be very valuable. Their extensive use has made it necessary to tighten definitions and testing guidance. This was accomplished for a good visual environment and is underway for degraded visual environments.

Key, David L.↗

NASA NTRS1991

Simulation evaluation of the effects of time delay and motion on rotorcraft handling qualities

A study aimed at determining the effects of simulator characteristics on perceived handling qualities is discussed. Evaluations were conducted with a baseline set of rotorcraft dynamics, using a simple transfer-function model of an uncoupled helicopter, under different conditions of visual and overall time delays. As the visual and motion parameters were changed, differences in pilot opinion were found reflecting a change in the pilots' perceptions of handling qualities, rather than changes in the aircraft model itself. It is concluded that it is necessary to tailor the motion washout dynamics to suit the task, with reduced washouts for precision maneuvering as compared to aggressive maneuvering. Visual-delay data suggest that it may be better to allow some time delay in the visual path to minimize the mismatch between visual and motion, rather than eliminate the visual delay entirely through lead compensation.

Mitchell, David G.↗

NASA NTRS1988

Rotorcraft handling-qualities design criteria development

Joint NASA/Army efforts at the Ames Research Center to develop rotorcraft handling-qualities design criteria began in earnest in 1975. Notable results were the UH-1H VSTOLAND variable stability helicopter, the VFA-2 camera-and-terrain-board simulator visual system, and the generic helicopter real-time mathematical model, ARMCOP. An initial series of handling-qualities studies was conducted to assess the effects of rotor design parameters, interaxis coupling, and various levels of stability and control augmentation. The ability to conduct in-flight handling-qualities research was enhanced by the development of the NASA/Army CH-47 variable-stability helicopter. Research programs conducted using this vehicle include vertical-response investigations, hover augmentation systems, and the effects of control-force characteristics. The handling-qualities data base was judged to be sufficient to allow an update of the military helicopter handling-qualities specification, MIL-H-8501. These efforts, including not only the in-house experimental work but also contracted research and collaborative programs performed under the auspices of various international agreements. The report concludes by reviewing the topics that are currently most in need of work, and the plans for addressing these topics.

Aiken, Edwin W.↗

NASA NTRS1987

New handling-qualities requirements and how they can be met

The structure and coverage of the proposed MIL-H-8501B specification for helicopter handling qualities are reviewed. The specification prescibes the desired vehicle command response as a function of the mission task and the usable visual cues. It takes into account failures and flight envelopes, and it prescribes a set of flight demonstration maneuvers. Helicopter performance requirements with degraded visual cues are proposed, in addition to specific longitudinal and lateral dynamics requirements.

Key, David L.↗

NASA NTRS1987

Update 8501: A new specification for rotorcraft handling qualities

MIL-H-8501B is a mission-oriented rotorcraft handling-qualities specification which prescribes the desired vehicle command response as a function of the mission task and the usable visual cues. It covers failures and flight envelopes, like MIL-F-8785C, but adds a novel concept in compliance testing in the form of a set of flight demonstration maneuvers. The proponents of this proposed specification including the authors, recognize that there are still many topics that are inadequately covered by it; they argue that it is nonetheless a significant improvement and should be adopted.

Key, David L.↗

NASA NTRS1982

Handling Qualities Specifications for U.S. Military Helicopters

Inadequacies in the military specification for helicopter handling qualities, MIL-H-8501A, have long been recognized, and the latest procurements by the U.S. Army used special Prime Item Development Specifications (PIDS). This paper assesses the efficacy of these PIDS and suggests that changes should be made. In particular, the structure developed in MIL-F-8785B (ASG) (the specification for flying qualities of piloted airplanes) should be incorporated. Improved requirements must be based on a systematic data base and concentrated on topics most important in preliminary design: static and dynamic stability, control power and sensitivity, and interaction with controllers and displays. Emphasis should be on current military helicopter missions and helicopter idiosyncrasies such as cross-coupling, nonlinearities, and higher-order dynamics.

Key, David L.↗