Search NASA⌕ Search

Engineering topics

Keyes, J. W.

Publications and source records attributed to Keyes, J. W..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Modifications to the nozzle test chamber to extend nozzle static-test capability

The nozzle test chamber was modified to provide a high-pressure-ratio nozzle static-test capability. Experiments were conducted to determine the range of the ratio of nozzle total pressure to chamber pressure and to make direct nozzle thrust measurements using a three-component strain-gage force balance. Pressure ratios from 3 to 285 were measured with several axisymmetric nozzles at a nozzle total pressure of 15 to 190 psia. Devices for measuring system mass flow were calibrated using standard axisymmetric convergent choked nozzles. System mass-flow rates up to 10 lbm/sec are measured. The measured thrust results of these nozzles are in good agreement with one-dimensional theoretical predictions for convergent nozzles.

Keyes, J. W.↗
NASA NTRS1985

Experimental study of forward-located jet-interaction nozzles

The effects of forward-mounted sonic jet-interaction nozzles with one, three equal, or one large and two small orifices on the transitional or turbulent boundary-layer flow over a biconic (9-deg-25-arcmin/6-deg) model at angle of attack -10 to the 15 deg and Reynolds number 8.10 x 10 to the 6th/ft are investigated experimentally using pressure taps, force measurements, oil-flow visualization, and schlieren photography in the 20-in. Mach-6 wind tunel at NASA Langley. The injection flow rates are 0.055 and 0.026 lbm/s, with stagnation pressure 500 psia, stagnation temperature 1000 R, and dynamic pressure 8.7 psia. The results are presented in diagrams, graphs, and photographs and characterized. Moment amplification factors of 1.0 or better (maximum 1.8 at angle of attack 15 deg and flow rate 0.055 lbm/s) are observed for all nozzle types, but the configuration with three unequal orifices is found to give improvements of 10 percent over the single-orifice nozzle at a given flow rate.

Cavalleri, R. J.↗
NASA NTRS1980

Noise reduction in a Mach 5 wind tunnel with a rectangular rod-wall sound shield

A rod wall sound shield was tested over a range of Reynolds numbers of 0.5 x 10 to the 7th power to 8.0 x 10 to the 7th power per meter. The model consisted of a rectangular array of longitudinal rods with boundary-layer suction through gaps between the rods. Suitable measurement techniques were used to determine properties of the flow and acoustic disturbance in the shield and transition in the rod boundary layers. Measurements indicated that for a Reynolds number of 1.5 x 10 to the 9th power the noise in the shielded region was significantly reduced, but only when the flow is mostly laminar on the rods. Actual nozzle input noise measured on the nozzle centerline before reflection at the shield walls was attenuated only slightly even when the rod boundary layer were laminar. At a lower Reynolds number, nozzle input noise at noise levels in the shield were still too high for application to a quiet tunnel. At Reynolds numbers above 2.0 x 10 the the 7th power per meter, measured noise levels were generally higher than nozzle input levels, probably due to transition in the rod boundary layers. The small attenuation of nozzle input noise at intermediate Reynolds numbers for laminar rod layers at the acoustic origins is apparently due to high frequencies of noise.

Creel, T. R., Jr.↗
NASA NTRS1977

Correlation of turbulent shear layer attachment peak heating near Mach 6

A correlation of new turbulent two-dimensional data and peak heating data for attaching free shear layers is presented for a 2.54-cm and 5.08-cm diam cylindrical leading-edge slab 25.4 cm long, and 7.62 and 10.16 cm wide. A 30.48 x 25.4 cm sharp leading-edge flat plate set at 15 and 20 deg is used to generate plane impinging shocks. The freestream Mach number is 6 and the freestream Reynolds number varies from 3,300,000 to 25,600,000/m. Peak heating is measured on silica-based epoxy models with a phase change coating technique. A comparison of the free shear layer data with the transition data of Birch and Keyes (1972) reveals that the shear layer data are turbulent at attachment. The trend of the data shows that peak heating is strongly affected by the state of development at attachment. As the free shear layers become more fully developed, the data approach the two-dimensional correlation. Persistence of transitional flow structures for supersonic free shear flows is pointed out.

Keyes, J. W.↗
NASA NTRS1977

Force testing manual for the Langley 20-inch Mach 6 tunnel

Data reduction and procedures for conducting force tests in a 20 inch Mach 6 tunnel are described. A discussion of pretest and testing phases are included. Items that are to be checked during model design and construction are outlined as well as safety requirements, starting loads tests, instructions for data acquisition and model installation. Measurement of balance and model misalignment and instructions for calibrating the angle of attack screen are covered. Procedures for making reference pressure, attitude tare, and data runs are included. The 20 inch tunnel force program is examined, and a description of data recording system input and load contrast sheets is given. An appendix presents a description, operating characteristics, and Mach number calibration of the tunnel, as well as tunnel characteristics.

Keyes, J. W.↗
NASA NTRS1977

Experimental verification of the technique for measurement of ablation on the GASJET nose tip

The GASJET nose tip is proposed to reduce the erosion at the apex of a missile nose flying at hypersonic speeds through a rain storm as it reenters the atmosphere. A forward facing sonic jet is directed through the tip introducing a secondary counter-flow which displaces the bow shock and blankets the tip with a protective layer of relatively cool gas. Wind tunnel experiments are described which proved the validity of measuring nose recession in flight by recording the pressure in the blast tube supplying the GASJET.

Donohoe, J. C.↗
NASA NTRS1976

Comparison of a two-dimensional shock impingement computation with experiment

Results of computations of two-dimensional viscous blunt-body flowfields with an impinging shock wave, with a time-dependent finite-difference method employed to solve the complete set of Navier-Stokes equations, are compared with experimental results. The experimental results were obtained in a 20-inch hypersonic tunnel with a planar shock impinging on the cylindrical leading edge of a fin, hence with the shock parallel to the centerline of the leading edge, so that type III and type IV interference patterns were generated. Close agreement is found. The overall effects of smoothing and grid size on the calculations are determined. A 31 x 51 mesh is adequate for wall pressure values (except in peaked regions).

Tannehill, J. C.↗
NASA NTRS1976

Shock interference peak heating measurements using phase change coatings

The phase change coating technique is used to obtain peak heating measurements in shock interference flow regions with high surface shear and heating. This technique provides heat transfer coefficients which are determined by measuring the time for a point on the surface to reach the phase change temperature of the thin fusible coating. Measurements were conducted on a 5.08-cm diameter hemisphere-cylinder made of silica based epoxy at Mach 6 for free stream Reynolds numbers of 3.3 to 25.6 million per meter. A sketch of the shock interference pattern produced by a flat plate shock generator is included. Heating data obtained on a 5.08-cm diameter stainless steel hemispherical model instrumented with thermocouples is presented for the purpose of comparing the phase change technique with the thermocouple-calorimeter technique.

Keyes, J. W.↗
NASA NTRS1973

Off-center-line shock interference heating patterns on basic shapes in hypersonic flows

The results of an experimental study of off-center-line shock-interference heating on basic shapes at hypersonic speeds are presented. The study covered three types of shock-interference patterns over a range of nominal Mach numbers (6 to 20), specific heat ratios (1.40 and 1.67), free-stream Reynolds numbers(8 million to 26 million per meter), and impinging shock strengths. Heat-transfer rates higher than stagnation levels were measured over much of the off-center-line model surface. Peak heating up to 17 times the stagnation heating was measured.

Keyes, J. W.↗
NASA NTRS1973

Analytical and experimental studies of shock interference heating in hypersonic flows

An analytical and experimental study is presented of the aerodynamic heating resulting from six types of shock interference patterns encountered in high speed flow. Centerline measurements of pressure and heat transfer distributions on basic bodies were obtained in four wind tunnels for Mach numbers from 6 to 20, specific heat ratios from 1.27 to 1.67, and free stream Reynolds numbers from 3 million to 25.6 million per meter. Peak heating and peak pressures up to 17 and 7.5 times stagnation values, respectively, were measured. In general, results obtained from semiempirical methods developed for each of the six types of interference agreed with the experimental peaks.

Keyes, J. W.↗
NASA NTRS1973

Computer programs for predicting supersonic and hypersonic interference flow fields and heating

This report describes computer codes which calculate two-dimensional shock interference patterns. These codes compute the six types of interference flows as defined by Edney (Aeronaut. Res. Inst. of Sweden FAA Rep. 115). Results include properties of the inviscid flow field and the inviscid-viscous interaction at the surface along with peak pressure and peak heating at the impingement point.

Morris, D. J.↗
NASA NTRS1972

Correlations of peak heating in shock interference regions at hypersonic speeds.

Correlations are given of measured pressure and heat-transfer peaks for shock/boundary-layer interactions and shear layer attachment on configurations with both two- and three-dimensional interactions. The peak values were obtained from an investigation of shock interference heating on hemispheres, a 30-deg included angle wedge, and a 2.54-cm-diam cylindrical leading-edge fin model. The investigation covers data for Mach numbers of 6 and 20 over freestream Reynolds numbers ranging from (3.3 to 25.6) million per meter, and specific heat ratios of 1.4 and 1.67.

Keyes, J. W.↗
NASA NTRS1972

Transition in compressible free shear layers.

The transition Reynolds number for shear layers produced by interactions between weak and strong shock waves is determined on the basis of experiments performed in a 20-in. (Mach 6) and an 11-in. (Mach 6.9) hypersonic tunnel. A variable angle wedge was used to generate a planar shock wave which interacted with the bow wave of a blunt body. An average value of the transition length (defined as the length along the shear layer from the shock interaction to the point where turbulence became visible on schlieren photographs) was used to determine the transition Reynolds number.

Birch, S. F.↗
NASA NTRS1972

Shock interference heating in hypersonic flows.

This paper presents results of a theoretical and experimental study of shock interference heating which encompassed a variety of basic body shapes and flow conditions. Measurements of pressure and heat transfer were obtained in four wind tunnels at NASA-Langley Research Center. These data cover the Mach number range from 6 to 20, and specific heat ratio range from 1.20 to 1.67. Peak heating measurements up to 17 times ordinary stagnation point rates and pressure peaks up to 8 times freestream pitot pressure were recorded. Numerical results from computer codes developed for each of the six types of interference compare favorably with most of the experimental data. A theoretical parametric study determined the effects of Mach number, specific heat ratio, and impinging shock strength on amplification of pressure and heat transfer. The results of this study show that shock interference is important for hypersonic vehicles such as the Space Shuttle. The problem is aggravated by changes along the flight path of the particular type of interference and the location of regions of peak heat transfer and pressure.

Hains, F. D.↗