Search NASA⌕ Search

Engineering topics

Khaleel, Mohammad A.

Publications and source records attributed to Khaleel, Mohammad A..

At least 19 records

Materials and engineering endeavors towards practical sodium-ion batteries

Sodium-ion batteries are making inroads toward better acceptance by both research and industry communities as promising electrochemical energy storage systems for stationary battery applications. Here, the extreme dedication to lithium-ion batteries, since the early 90s, has eclipsed any significant development around room temperature Na-ion batteries, despite the materials availability advantage the latter have over the Li-ion battery counterparts. Benefiting from the substantial knowledge accumulated on Li-ion batteries, tremendous progress rapidly occurred with focus on solving the fundamental issues encountered at the component, system and cost levels in Na-ion batteries. In this review, we discuss the key aspects that make Na-ion batteries enable the research of a wide spectrum of sodium-based materials and electrolytes, which further catalyzes the development of plethora of energy storage systems.

25 ENERGY STORAGE↗

Extreme fast charging characteristics of zirconia modified LiNi 0.5 Mn 1.5 O 4 cathode for lithium ion batteries

LiNi 0.5 Mn 1.5 O 4 is a promising high-voltage cathode for lithium-ion battery fast charging applications. Aware of its electrochemical stability issues, the material's surface is modified with small amounts of zirconia (ZrO 2 ) ranging from 0.5 to 2 wt% using a scalable ball milling process. The advantage of the coating has been demonstrated in electrochemical measurements performed at room temperature and 55 °C, and in cells discharged under high-rate conditions up to 80C. Of significance, the material coated with 1.0 wt% ZrO 2 has been cycled at the 40C rate for over a thousand cycles and retains 86% of its initial capacity. The material with 2.0 wt% ZrO 2 modification preserves 76% of its initial capacity when cycled at the 40C rate and 55 °C. The coated materials have shown excellent cycling stability when subjected to 6C (10-min) fast charging and C/3 discharging for 300 cycles. Compared to the uncoated material, the interfacial resistance of the zirconia modified LiNi 0.5 Mn 1.5 O 4 has been found to be much lower and does not significantly increase with increasing the coating amount. However, the electrochemical performances are still partly limited by both interfacial resistance at the beginning of charge and electrolyte diffusivity, particularly under higher rate cycling conditions. Altogether, the strategy of ZrO 2 surface modification applied to LiNi 0.5 Mn 1.5 O 4 unveils the potential that the material could play in extreme fast charged electric vehicles.

25 ENERGY STORAGE↗

Mechanical properties of water desalination and wastewater treatment membranes

Applications of membrane technology in water desalination and wastewater treatment have increased significantly in the past fewdecades due to itsmany advantages over otherwater treatment technologies.Water treatment membranes provide high flux and contaminant rejection ability and require good mechanical strength and durability. Thus, assessing the mechanical properties of water treatment membranes is critical not only to their design, but also for studying their failure mechanisms, including the surface damage, mechanical and chemical ageing, delamination and loss of dimensional stability of the membranes. The various experimental techniques to assess themechanical properties ofwastewater treatment and desalinationmembranes are reviewed. Uniaxial tensile test, bending test, dynamic mechanical analysis, nanoindentation and bursting tests are the most widely used mechanical characterization methods for water treatment membranes. Mechanical degradations induced by fouling, chemical cleaning as well as membrane delamination are then discussed. Moreover, in order to study the membranesmechanical responses under similar loading conditions, the stress-state of the membranes are analyzed and advanced mechanical testing approaches are proposed. Lastly, some perspectives are highlighted to study the structure-properties relationship for wastewater treatment and water desalination membranes.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Molecular Dynamics Simulation of Thermodynamic Properties in Uranium Dioxide

In the present study, we investigated the thermodynamic properties of uranium dioxide (UO2) by molecular dynamics (MD) simulations. As for solid UO2, the lattice parameter, density, and enthalpy obtained by MD simulations were in good agreement with existing experimental data and previous theoretical predictions. The calculated thermal conductivities matched the experiment results at the midtemperature range but were underestimated at very low and very high temperatures. The calculation results of mean square displacement represented the stability of uranium at all temperatures and the high mobility of oxygen toward 3000 K. By fitting the diffusivity constant of oxygen with the Vogel-Fulcher-Tamman law, we noticed a secondary phase transition near 2006.4 K, which can be identified as a ‘‘strong’’ to ‘‘fragile’’ supercooled liquid or glass phase transition in UO2. By fitting the oxygen diffusion constant with the Arrhenius equation, activation energies of 2.0 and 2.7 eV that we obtained were fairly close to the recommended values of 2.3 to 2.6 eV. Xiangyu Wang, Bin Wu, Fei Gao, Xin Li, Xin Sun, Mohammed A. Khaleel, Ademola V. Akinlalu and Li Liu

Computer Simulation↗

Modeling of deformation behavior and texture evolution in magnesium alloy using the intermediate $\phi$-model

The viscoplastic intermediate phi-model was applied in this work to predict the deformation behavior and texture evolution in a magnesium alloy, an HCP material. We simulated the deformation behavior with different intergranular interaction strengths and compared the predicted results with available experimental results. In this approach, elasticity is neglected and the plastic deformation mechanisms are assumed as a combination of crystallographic slip and twinning systems. Tests are performed for rolling (plane strain compression) of random textured Mg polycrystal as well as for tensile and compressive tests on rolled Mg sheets. Simulated texture evolutions agree well with experimental data. Activities of twinning and slip, predicted by the intermediate $\phi$-model, reveal the strong anisotropic behavior during tension and compression of rolled sheets.

$\phi$-Model↗

Three-Dimensional Reconstruction and Microstructure Modeling of Porosity-Graded Cathode Using Focused Ion Beam and Homogenization Techniques

In this study, microstructure of a porosity-graded lanthanum strontium manganite (LSM) cathode of solid oxide fuel cells (SOFCs) has been characterized using focused ion beam (FIB) and scanning electron microscopy(SEM) combined with image processing. Two-point correlation functions of the two-dimensional (2D) images taken along the direction of porosity gradient are used to reconstruct a three-dimensional (3D) microstructure. The effective elastic modulus of the two-phase porosity-graded cathode is predicted using strong contrast (SC) and composite inclusion (CI) homogenization techniques. The effectiveness of the two methods in predicting the effective elastic properties of the porositygraded LSM cathode is investigated in comparison with the results obtained from the finite element model (FEM).

25 ENERGY STORAGE↗

Yield asymmetry design of magnesium alloys by integrated computational materials engineering

Deformation asymmetry of magnesium alloys is an important factor on machine design in the automobile industry. Represented by the ratio of compressive yield stress (CYS) against tensile yield stress (TYS), deformation asymmetry is strongly related to texture and grain size. A polycrystalline viscoplasticity model, modified intermediate Φ-model, is used to predict the deformation behavior of magnesium alloys with different grain sizes. Validated with experimental results, integrated computational materials engineering is applied to find out the route in achieving desired asymmetry via thermomechanical processing. For example, CYS/TYS in rolled texture is smaller than 1 under different loading directions. In other textures, such as extruded texture, CYS/TYS is large along the normal direction. Starting from rolled texture, asymmetry will increase to close to 1 along the rolling direction after being compressed to a strain of 0.2. Our modified Φ-model also shows that grain refinement increases CYS/TYS. Along with texture control, grain refinement also can optimize the yield asymmetry. After the grain size decreases to a critical value, CYS/TYS reaches to 1 because CYS increases much faster than TYS. By tailoring the microstructure using texture control and grain refinement, it is achievable to optimize yield asymmetry in wrought magnesium alloys.

36 MATERIALS SCIENCE↗

Simulation of cooling and solidification of three-dimensional bulk borosilicate glass. Effect of structural relaxations

The modeling of the viscoelastic stress evolution and specific volume relaxation of a bulky glass cast is presented in this article and is applied to the experimental cooling process of an inactive nuclear waste vitrification process. The concerned borosilicate glass is solidified and cooled down to ambient temperature in a stainless steel canister, and the thermomechanical response of the package is simulated. There exists a deviant compression of the liquid core due to the large glass package compared to standard tempered glass plates. The stress load development of the glass cast is finally studied for different thermal load scenarios, where the cooling process parameters or the final cooldown rates were changed, and we found a great influence of the studied cooldown rates on the maximum stress buildup at ambient temperature.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Grand Challenges of Advanced Computing for Energy Innovation Report from the Workshop Held July 31-August 2, 2012

On July 31-August 2 of 2012, the U.S. Department of Energy (DOE) held a workshop entitled Grand Challenges of Advanced Computing for Energy Innovation. This workshop built on three earlier workshops that clearly identified the potential for the Department and its national laboratories to enable energy innovation. The specific goal of the workshop was to identify the key challenges that the nation must overcome to apply the full benefit of taxpayer-funded advanced computing technologies to U.S. energy innovation in the ways that the country produces, moves, stores, and uses energy. Perhaps more importantly, the workshop also developed a set of recommendations to help the Department overcome those challenges. These recommendations provide an action plan for what the Department can do in the coming years to improve the nation’s energy future.

Larzelere, Alex R.↗

Computational Modeling of Transport Limitations in Li-Air Batteries

In this paper we investigate transport limitations in the electrodes of lithium-air batteries through computational modeling. We use meso-scale models to consider the effects of dendrites on the current and potential at the anode surface, and to investigate the effects of reaction and transport parameters on the formation of precipitates in the cathode. The formation of dendrites on the anode surface during cycling reduces the transport of ions and can lead to short circuits in the cell. Growth of precipitates in the cathode reduces the specific capacity of the cell due to surface passivation and pore clogging. Both of these degradation mechanisms depend on meso-scale phenomena, such as the pore-scale reactive transport in the cathode. To understand the effects of the meso-scale transport and precipitation on the performance and lifetime of Li-air batteries, meso-scale modeling is needed that is able to resolve the electrodes and their microstructures.

Li-Air Batteries, Smoothed Particle Hydrodynamics,↗

Surface Treatments for Improved Performance of Spinel-coated AISI 441 Ferritic Stainless Steel

Ferritic stainless steels are promising candidates for IT-SOFC interconnect applications due to their low cost and resistance to oxidation at SOFC operating temperatures. However, steel candidates face several challenges; including long term oxidation under interconnect exposure conditions, which can lead to increased electrical resistance, surface instability, and poisoning of cathodes due to volatilization of Cr. To potentially extend interconnect lifetime and improve performance, a variety of surface treatments were performed on AISI 441 ferritic stainless steel coupons prior to application of a protective spinel coating. The coated coupons were then subjected to oxidation testing at 800 and 850°C in air, and electrical testing at 800°C in air. While all of the surface-treatments resulted in improved surface stability (i.e., increased spallation resistance) compared to untreated AISI 441, the greatest degree of improvement (through 20,000 hours of testing at 800°C and 14,000 hours of testing at 850°C) was achieved by surface blasting.

36 MATERIALS SCIENCE↗

Development of a Mechanistic-Based Healing Model for Self-Healing Glass Seals

Self-healing glass, a recent development of hermetic sealant materials, has the ability to effectively repair damage when heated to elevated temperatures; thus, able to extend its service life. Since crack healing morphological changes in the glass material are usually temperature and stress dependent, quantitative studies to determine the effects of thermo-mechanical conditions on the healing behavior of the self-healing glass sealants are extremely useful to accommodate the design and optimization of the sealing systems within SOFCs. The goal of this task is to develop a mechanistic-based healing model to quantify the stress and temperature dependent healing behavior. A two-step healing mechanism was developed and implemented into finite element (FE) models through user-subroutines. Integrated experimental/kinetic Monte Carlo (kMC) simulation methodology was taken to calibrate the model parameters. The crack healing model is able to investigate the effects of various thermo-mechanical factors; therefore, able to determine the critical conditions under which the healing mechanism will be activated. Furthermore, the predicted results can be used to formulate the continuum damage-healing model and to assist the SOFC stack level simulations in predicting and evaluating the effectiveness and the performance of various engineering seal designs.

Fuel Cell↗

Comparison of Different Upscaling Methods for Predicting Thermal Conductivity of Complex Heterogeneous Materials System: Application on Nuclear Waste Forms

To develop a strategy in thermal conductivity prediction of a complex heterogeneous materials system, loaded nuclear waste forms, the computational efficiency and accuracy of different upscaling methods have been evaluated. The effective thermal conductivity, obtained from microstructure information and local thermal conductivity of different components, is critical in predicting the life and performance of waste form during storage. Several methods, including the Taylor model, Sachs model, self-consistent model, and statistical upscaling method, were developed and implemented. Microstructure based finite element method (FEM) prediction results were used to as benchmark to determine the accuracy of the different upscaling methods. Micrographs from waste forms with varying waste loadings were used in the prediction of thermal conductivity in FEM and homogenization methods. Prediction results demonstrated that in term of efficiency, boundary models (e.g., Taylor model and Sachs model) are stronger than the self-consistent model, statistical upscaling method, and finite element method. However, when balancing computational efficiency and accuracy, statistical upscaling is a useful method in predicting effective thermal conductivity for nuclear waste forms.

36 MATERIALS SCIENCE↗

Large Scale DD Simulation Results for Crystal Plasticity Parameters in Fe-Cr And Fe-Ni Systems

The development of viable nuclear energy source depends on ensuring structural materials integrity. Structural materials in nuclear reactors will operate in harsh radiation conditions coupled with high level hydrogen and helium production, as well as formation of high density of point defects and defect clusters, and thus will experience severe degradation of mechanical properties. Therefore, the main objective of this work is to develop a capability that predicts aging behavior and in-service lifetime of nuclear reactor components and, thus provide an instrumental tool for tailoring materials design and development for application in future nuclear reactor technologies. Towards this end goal, the long term effort is to develop a physically based multiscale modeling hierarchy, validated and verified, to address outstanding questions regarding the effects of irradiation on materials microstructure and mechanical properties during extended service in the fission and fusion environments. The focus of the current investigation is on modern steels for use in nuclear reactors including high strength ferritic-martensitic steels (Fe-Cr-Ni alloys). The effort is to develop a predicative capability for the influence of irradiation on mechanical behavior. Irradiation hardening is related to structural information crossing different length scales, such as composition, dislocation, and crystal orientation distribution. To predict effective hardening, the influence factors along different length scales should be considered. Therefore, a hierarchical upscaling methodology is implemented in this work in which relevant information is passed between models at three scales, namely, from molecular dynamics to dislocation dynamics to dislocation-based crystal plasticity. The molecular dynamics (MD) was used to predict the dislocation mobility in body centered cubic (bcc) Fe and its Ni and Cr alloys. The results are then passed on to dislocation dynamics to predict the critical resolved shear stress (CRSS) from the evolution of local dislocation and defects. In this report the focus is on the results obtained from large scale dislocation dynamics simulations. The effect of defect density, materials structure was investigated, and evolution laws are obtained. These results will form the bases for the development of evolution and hardening laws for a dislocation-based crystal plasticity framework. The hierarchical upscaling method being developed in this project can provide a guidance tool to evaluate performance of structural materials for next-generation nuclear reactors. Combined with other tools developed in the Nuclear Energy Advanced Modeling and Simulation (NEAMS) program, the models developed will have more impact in improving the reliability of current reactors and affordability of new reactors.

36 MATERIALS SCIENCE↗

Relationship between Material Properties and Local Formability of DP980 Steels

A noticeable degree of inconsistent forming behaviors has been observed for the 1st generation advanced high strength steels (AHSS) in production, and they appear to be associated with the inherent microstructural-level inhomogeneities for various AHSS. This indicates that the basic material property requirements and screening methods currently used for the mild steels and high strength low alloys (HSLA) are no longer sufficient for qualifying today’s AHSS. In order to establish more relevant material acceptance criteria for AHSS, the fundamental understandings on key mechanical properties and microstructural features influencing the local formability of AHSS need to be developed. For this purpose, in this study, DP980 was selected as model steels and eight different types of DP980 sheet steels were acquired from various steel suppliers. Various experiments were then performed on the eight different DP980 steels such as chemical composition analysis, static tensile test, hole expansion test, channel forming test. Scanning electron microscope (SEM) pictures of the DP980 steels were also obtained, and image processing tools were then adopted to those SEM pictures in order to quantify their various microstructural features. The results show that all DP980 steels show large discrepancy in their performance and that the tensile properties and hole expansion properties of these steels do not correlate with their local formability. According to the results up to date, it is not possible to correlate the microstructural features alone to the macroscopically measured deformation behaviors. In addition to image analysis, other experiments (i.e., nano-indentation test) are also planned to quantify the individual phase properties of the various DP steels.

DP steel↗

Influence of grain boundary character on point defect formation energies in BCC Fe

The objective of this research is to understand how grain boundary character influences formation of vacancies and interstitials to grain boundaries in BCC Fe. In this study, molecular statics simulations were used to obtain a large number of minimum energy grain boundary structures in the <100> and <110> symmetric tilt grain boundary system. Then, simulations were used to calculate the formation energies associated with vacancies and self-interstitial atoms at atomic positions within 20 Angstroms of the boundary. As a first analysis, the vacancy formation energies are examined here. The simulation results show how the vacancy formation energies are influenced by grain boundary structure. Low angle boundaries are found to be an effective sink for vacancies along planes adjacent to grain boundary dislocations, while high angle low sigma grain boundaries are less effective sinks for vacancies. The grain boundary sink strength is postulated to depend upon the minimum vacancy formation energy and the influence of grain boundary character on this is shown. Interestingly, low sigma boundaries in the <100> symmetric tilt grain boundary system have higher minimum vacancy formation energies, while this quantity does not seem to be influenced by misorientation angle or grain boundary energy. The significance of this research is that atomistic simulations of this kind may ultimately help inform damage evolution via grain boundaries in multiscale models for irradiated materials as well as its implications for grain boundary engineering.

BCC Fe↗

EFFECT OF METALLIC INTERCONNECT THICKNESS ON ITS LONG-TERM PERFORMANCE IN SOFCS

At the operating environment of solid oxide fuel cells (SOFCs), oxide scale will grow on the ferritic interconnect (IC) surface unavoidably and furfures induce growth stress in oxide scale and along the interface of the oxide scale and IC substrate. A combination of growth stress with thermal stresses may lead to scale delamination/buckling and eventual spallation during SOFC stack cooling, even leading to serious degradation of cell performance. In this paper, the effect of the ferritic IC thickness on the delamination/spallation of the oxide scale was investigated numerically. The predicted results show that the interfacial shear stresses increase with the growth of the oxide scale and also with the thickness of the ferritic substrate; i.e., the thick ferritic substrate can easily lead to scale delamination and spallation.

delamination and spallation↗

Behavior of Aging, Micro-Void, and Self-Healing of Glass/Ceramic Materials and Its Effect on Mechanical Properties

This chapter first describes tests to investigate the temporal evolution of the volume fraction of ceramic phases, the evolution of micro-damage, and the self-healing behavior of the glass ceramic sealant used in SOFCs, then a phenomenological model based on mechanical analogs is developed to describe the temperature dependent Young’s modulus of glass ceramic seal materials. It was found that after the initial sintering process, further crystallization of the glass ceramic sealant does not stop, but slows down and reduces the residual glass content while boosting the ceramic crystalline content. Under the long-term operating environment, distinct fibrous and needle-like crystals in the amorphous phase disappeared, and smeared/diffused phase boundaries between the glass phase and ceramic phase were observed. Meanwhile, the micro-damage was induced by the cooling-down process from the operating temperature to the room temperature, which can potentially degrade the mechanical properties of the glass/ceramic sealant. The glass/ceramic sealant self-healed upon reheating to the SOFC operating temperature, which can restore the mechanical performance of the glass/ceramic sealant. The phenomenological model developed here includes the effects of continuing aging and devitrification on the ceramic phase volume fraction and the resulted mechanical properties of glass ceramic seal material are considered. The effects of micro-voids and self-healing are also considered using a continuum damage mechanics (CDM) model. The formulation is for glass/ceramic seal in general, and it can be further developed to account for effects of various processing parameters. This model was applied to G18, and the temperature-dependent experimental measurements were used to calibrate the modeling parameters and to validate the model prediction.

aging↗