Engineering topics

Khodadoust, A.

Publications and source records attributed to Khodadoust, A..

10 records

NASA NTRS1993

LDV flowfield measurements on a straight and swept wing with a simulated ice accretion

Simulated glaze ice accretion effects on a flowfield are presently studied for the case of a 3D semispan wing with NACA 0012 airfoil section on a rectangular untwisted planform. The model was tested at both zero-sweep and 30-deg sweep setting with four-beam/two-color LDV flowfield mapping. The comparison of LDV-measure velocity profiles with 3D Navier-Stokes predictions revealed correct trends, but with several differences that are attributable to the turbulence models and grid resolution used in the computations.

Bragg, M. B.↗

NASA NTRS1992

Measurements in a leading-edge separation bubble due to a simulated airfoil ice accretion

The separation bubble formed on an airfoil at low Reynolds number behind a simulated leading-edge glaze ice accretion is studied experimentally. Surface pressure and split hot-film measurements as well as flow visualization studies of the bubble reattachment point are reported. The simulated ice generates an adverse pressure gradient that causes a laminar separation bubble of the long bubble type to form. The boundary layer separates at a location on the ice accretion that is independent of angle of attack and reattaches at a downstream location 5-40 percent chord behind the leading edge, depending on the angle of attack. Velocity profiles show a large region of reverse flow that extends up from the airfoil surface as much as 2.5 percent chord. After reattachment, a thick distorted turbulent boundary layer exists. The separation bubble growth and reattachment are clearly seen in the plots of boundary-layer momentum thickness vs surface distance. Local minima and maxima in the boundary-layer momentum thickness development compare well with the shear layer transition point as indicated by the surface pressures and the reattachment point as measured from surface oil flow, respectively.

Bragg, M. B.↗

NASA NTRS1992

Finite wing aerodynamics with simulated glaze ice

The effect of a simulated glaze ice accretion on the aerodynamic performance of a three-dimensional wing is studied experimentally. The model used for these tests was a semi-span wing of effective aspect ratio five, mounted from the sidewall of the UIUC subsonic wind tunnel. The model has an NACA 0012 airfoil section on a rectangular, untwisted planform with interchangeable leading edges to allow for testing both the baseline and the iced wing geometry. A three-component sidewall balance was used to measure lift, drag and pitching moment on the clean and iced model. A four-beam two-color fiberoptic laser Doppler velocimeter (LDV) was used to map the flowfield along several spanwise cuts on the model. Preliminary results from LDV scans, which will be the bulk of this paper, are presented following the force balance measurement results. Initial comparison of LDV surveys compare favorably with inviscid theory results and 2D split hot-film measurements near the model surface.

Khodadoust, A.↗

NASA NTRS1992

LDV measurements on a rectangular wing with a simulated glaze ice accretion

LDV measurement results are presented for the upper surface of a rectangular semispan wing with and without simulated glaze ice accretion. Inspection of the model centerline flow field indicates that a large region of reverse flow exists aft of the ice horn on the iced model. At alpha = 0 deg, this region extends to 7 percent chord, while at alpha = 4 deg the bubble grows to more than 12 percent chord. At alpha = 8 deg, the time-averaged separation bubble is measured well beyond 50 percent chord. Experimental and computational flow visualization support these findings. The flow in the vicinity of the ice shape contains many of the features of flow over a backward-facing step.

Khodadoust, A.↗

NASA NTRS1992

Aerodynamics of a finite wing with simulated ice

The effect of a simulated glaze ice accretion on the aerodynamic performance of a three-dimensional wing is studied experimentally. Results are reviewed from earlier two-dimensional tests which show the character of the large leading-edge separation bubbles caused by the simulated ice accretion. The 2-D bubbles are found to closely resemble well known airfoil laminar separation bubbles. For the 3-D experiments a semispan wing of effective aspect ratio five was mounted from the sidewall of the UIUC subsonic wind tunnel. The model uses a NACA 0012 airfoil section on a rectangular planform with interchangeable tip and root sections to allow for 0- and 30-degree sweep. A three-component sidewall balance was used to measure lift, drag and pitching moment on the clean and iced model. Fluorescent oil flow visualization has been performed on the iced model and reveals extensive spanwise and vortical flow in the separation bubble aft of the upper surface horn. Sidewall interaction and spanwise nonuniformity are also seen on the unswept model. Comparisons to the computed flow fields are shown. Results are also shown for roughness effects on the straight wing. Sand grain roughness on the ice shape is seen to have a different effect than isolated 3-D roughness elements.

Bragg, M. B.↗

NASA NTRS1991

Effect of a simulated ice accretion on the aerodynamics of a swept wing

The effect of a simulated glaze ice accretion on the aerodynamic performance of a three-dimensional swept wing is studied experimentally. A semispan wing of effective aspect ratio four was mounted from the sidewall of the UIUC subsonic wind tunnel. The model uses a NACA 0012 airfoil section on a rectangular planform with interchangeable tip and root sections to allow for 0- and 30-degree sweep. A sidewall suction system is used to minmize the tunnel boundary-layer interaction with the model. Surface pressure data from five spanwise stations are compared to earlier data from a similar tunnel. A three-component sidewall balance has been designed, built and used to measure lift, drag and pitching moment on the clean and iced model. The data compare well to the integrated pressure data and to theory on the clean model. In addition, helium-bubble flow visualization has been performed on the iced model and reveals extensive spanwise flow in the separation bubble aft of the upper surface horn. This compares well to the computational results of other researchers. Sidewall suction was found to have no effect on the aerodynamics of the swept wing.

Bragg, M. B.↗

NASA NTRS1991

Aerodynamic measurements on a finite wing with simulated ice

The effect of a simulated glaze ice accretion on the aerodynamic performance of a three-dimensional straight and swept wing is studied experimentally. A semispan wing of effective aspect ratio five was mounted from the sidewall of the UIUC subsonic wind tunnel. The model uses an NACA 0012 airfoil section on a rectangular planform with interchangeable tip and root sections to allow for 0- and 30-deg sweep. A sidewall suction system is used to minimize the tunnel boundary-layer interaction with the model. A three-component sidewall balance has been designed, built and used to measure lift, drag and pitching moment on the clean and iced model. Fluorescent oil flow visualization has been performed on the iced model and reveals extensive spanwise flow in the separation bubble aft of the upper surface horn. These results are compared to computational results for the surface pressures, span loads and surface oil flow.

Bragg, M. B.↗

NASA NTRS1990

Measured aerodynamic performance of a swept wing with a simulated ice accretion

The effect of a simulated glaze ice accretion on the aerodynamic performance of a three-dimensional swept wing is studied experimentally. A semispan wing of effective aspect ratio four was mounted from a splitter plate in the OSU subsonic wind tunnel. The model uses a NACA 0012 airfoil section on a rectangular planform with interchangeable tip and root pieces to allow for 0- and 30-degree sweep. Surface pressures were measured at 5 semispan locations on the swept-wing model. The section lift data for the 5 semispan locations are presented and compared with theory and zero-sweep model results. In addition, previously unpublished roughness data from the zero-sweep model is presented here. These data show a large drag and maximum lift penalty due to rough simulated glaze ice. The effect of wing-sweep is seen through a decrease in wing lift performance for both the clean and iced wing.

Khodadoust, A.↗

NASA NTRS1989

Effect of simulated glaze ice on a rectangular wing

Experimental measurements of the effect of simulated glaze ice on a three-dimensional wing are presented. A semispan wing of effective aspect ratio five was mounted from a splitter plate in the OSU subsonic wind tunnel. The model has a straight, untwisted rectangular platform, and uses a NACA 0012 airfoil section. Surface pressures were measured at 5 semispan locations and a total-pressure wake-survey probe was used on the model centerline. The section lift and drag data from the model centerline compared well to earlier two-dimensional data. These data show a large drag and maximum lift penalty due to the simulated glaze ice. Three-dimensional span-load data compare well to computational results.

Bragg, M. B.↗

NASA NTRS1988

Experimental measurements in a large separation bubble due to a simulated glaze ice shape

The effect of a simulated glaze ice accretion on the aerodynamic performance of a NACA 0012 airfoil was studied experimentally. Two ice shapes were tested, one from an experimentally measured accretion and one from an accretion predicted using a computer model given the same icing conditions. Lift, drag and moment coefficients were measured for the airfoil with both ice shapes, smooth and rough. The aerodynamic performance of the two shapes compared well at positive, but not negative, angles of attack. Split hot-film probe velocity data were presented in the upper surface boundary layer and in the wake. Boundary layer parameters were presented for the separation bubble and in the reattached turbulent boundary layer.

Bragg, M. B.↗