Superior Performance of Aqueous LiFePO4 Cathodes Dispersions via Corona Treatment and Surface Energy Optimization
No abstract prepared.
Engineering topics
Publications and source records attributed to Kiggans, Jim.
No abstract prepared.
Utilization of titanium components made by powder metallurgy methods has had limited acceptance largely due to the high cost of titanium (Ti) powder. There has been renewed interest in lower cost powder and several Ti reduction methods that produce a particulate product show promise. This talk summarizes work done at Oak Ridge National Laboratory to consolidate these lower cost powders into mill products. Press and sinter consolidation, hot isostatic pressing (HIP) and direct roll consolidation to make sheet have been explored. The characteristics of the consolidated products will be described as a function of the consolidation parameters. Research sponsored by the U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Industrial Technologies Program, under contract DE-AC05-00OR22725 with UT-Battelle, LLC.
An overview of the metal matrix microencapsulated (M3) fuel concept for the specific LWR application has been provided. Basic fuel properties and characteristics that aim to improve operational reliability, enlarge performance envelope, and enhance safety margins under design-basis accident scenarios are summarized. Fabrication of M3 rodlets with various coated fuel particles over a temperature range of 800-1300 C is discussed. Results from preliminary irradiation testing of LWR M3 rodlets with surrogate coated fuel particles are also reported.
Graphene materials derived through the exfoliation of graphite are always accompanied with high population of defects and/or surface functionalities due to the harsh conditions utilized in the synthesis. We describe herein a scalable approach for the preparation of high quality graphene materials via low-temperature exfoliation of graphite under mild chemical conditions. The microwave induced rapid decomposition of nitromethane at low temperature produces mechanical force that lifts up the graphene sheets from the FeCl 3 and CH 3 NO 2 co-intercalated graphite compound without creating defects and functional groups.
This work investigates the cold compaction behavior of Ti-6Al-4V powders produced by Armstrong Process . As-received as well as milled powders were characterized and these powders were uniaxially die-pressed at designated pressures up to 690 MPa to form disk samples with different aspect ratios. Samples with high aspect ratio exhibited non-uniform density along the pressing axis and the density distribution is in consistent with the result predicted by finite element analysis. The linear regression analysis on the experimental density data can be used to predict density of compacts with different aspect ratios. In the studied pressure range, an empirical powder compaction equation represents the green density pressure relationship very well for both the as-received and 1-hr milled Armstrong Ti-6Al-4V powders.
Self-assembled mesoporous carbon (MC) materials have been synthesized and tested for application in capacitive deionization (CDI) of saline water. MC was prepared by self-assembly of a triblock copolymer with hydrogen-bonded chains via a phenolic resin, such as resorcinol or phloroglucinol in acidic conditions, followed by carbonization and, in some cases, activation by KOH. Carbon synthesized in this way was ground into powder, from which activated MC sheets were produced. In a variation of this process, after the reaction of triblock copolymer with resorcinol or phloroglucinol, the gel that was formed was used to coat a graphite plate and then carbonized. The coated graphite plate in this case was not activated and was tested to serve as current collector during the CDI process. The performance of these MC materials was compared to that of carbon aerogel for salt concentrations ranging between 1000 ppm and 35,000 ppm. Resorcinol-based MC removed up to 15.2 mg salt per gram of carbon, while carbon aerogel removed 5.8 mg salt per gram of carbon. Phloroglucinol-based MC-coated graphite exhibited the highest ion removal capacity at 21 mg of salt per gram of carbon for 35,000 ppm salt concentration.
To fabricate LiFePO4 battery cathodes, highly conductive carbon fibers of 10-20 m in diameter have been used to replace a conventional aluminum (Al) foil current collector. This disperses the current collector throughout the cathode sheet and increases the contact area with the LiFePO4 (LFP) particles. In addition, the usual organic binder plus carbon-black can be replaced by a high temperature binder of <5 weight % carbonized petroleum pitch (P-pitch). Together these replacements increase the specific energy density and energy per unit area of the electrode. Details of the coating procedure, characterization and approach for maximizing the energy density are discussed. In a side-by-side comparison with conventional cathodes sheets of LFP on Al foil, the carbon fiber composite cathodes have a longer cycle life, higher thermal stability, and high capacity utilization with little sacrifice of the rate performance.
A novel lithium ion battery cathode structure was produced which has the potential for excellent capacity retention and good thermal management. In these cathodes, the active cathode material (lithium iron phosphate) was carbon bonded to a thermally and electrically conductive carbon fiber paper (CFP) support. Electrochemical testing was performed on Swagelok cells consisting of CFP cathodes and lithium anodes. High specific energy, near-theoretical capacity, and good cycling performance were demonstrated for 0.11 mm and 0.37 mm thick CFP cathodes.
This paper summarizes our recent efforts to develop the manufacturing technologies of consolidated net-shape components by using new low-cost commercially pure titanium (CP-Ti) and Ti-6Al-4V alloy powders made by the Armstrong process. Fabrication processes of net shape/ near net shape components, such as uniaxial die-pressing, cold isostatic pressing (CIP), sintering, roll compaction and stamping, have been evaluated. The press-and-sinter processing of the powders were systematically investigated in terms of theoretical density and microstructure as a function of time, pressure, and temperature. Up to 96.4% theoretical density has been achieved with the press-and-sinter technology. Tensile properties of the consolidated samples exhibit good ductility as well as equivalent yield/ultimate tensile strengths to those of fully consolidate materials, even with the presence of a certain amount of porosity. A consolidation model is also under development to interpret the powder deformation during processing. Net shape components made of the Armstrong powder can successfully be fabricated with clearer surface details by using press-and-sinter processing.
No abstract prepared.
A review of the mechanical property data needed for the process simulation of cold pressing was conducted. The material property data for the newly developed low-cost commercially pure titanium, CP-Ti, powders made by Armstrong process was presented. The following data was obtained from mechanical testing: Youngs modulus, bulk modulus, failure line for the plasticity model. The Youngs modulus and bulk modulus were obtained from the uniaxial compression tests of a cylinder. The failure line for the plasticity model was obtained from failure compression tests. Materials testing software was written to provide automatic test control and data acquisition during material testing, such as axial displacement, axial stress, radial strain, and failure stress.
Templated carbon materials have recently received tremendous attention due to energy storage and separations applications. Hierarchical structures are ideal for increased mass-transport throughout the carbon material. A new ordered mesoporous carbon material has been developed using glyoxal which exhibits a hierarchical structure with pore sizes up to 200 nm. The hierarchical structure arises from the cross linking reagent and not from the standard spinodal decomposition of a secondary solvent. The carbon material was studied for potential application as a capacitive deionization (CDI) electrode for brackish water. Results indicate that the hierarchical structure provides a pathway for faster adsorption kinetics when compared to standard resorcinol-formaldehyde CDI electrodes.
No abstract prepared.