Search NASA⌕ Search

Engineering topics

Kim, J S

Publications and source records attributed to Kim, J S.

At least 19 records

Specific heat to H c⁢2 : Evidence for nodes or deep minima in the superconducting gap of underdoped and overdoped Ba(Fe 1–$x$ Co $x$ ) 2 As 2

Low-temperature specific heat, C, in magnetic fields up to Hc2 is reported for underdoped Ba(Fe 0.955 Co 0.045 ) 2 As 2 (T c = 8 K) and for three overdoped samples Ba(Fe 1–x Co x ) 2 As 2 (x = 0.103, 0.13, and 0.15; T c = 17.2, 16.5, and 11.7 K, respectively). Previous measurements of thermal conductivity (as a function of temperature and field) and penetration depth on comparable-composition samples gave some disagreement as to whether there was fully gapped/nodal behavior in the under-/overdoped materials, respectively. The present work shows that the measured behavior of the specific heat γ (∝C/T as T → 0, i.e., a measure of the electronic density of states at the Fermi energy) as a function of field approximately obeys γ ∝ H 0.5±0.1 , similar to the Volovik effect for nodal superconductors, for both the underdoped and the most overdoped Co samples. However, for the two overdoped compositions x = 0.103 and 0.13, the low-field (H ≤ 10 T) data show a Volovik-like behavior of γ ∝ H 0.3–0.4 , followed by an inflection point, followed at higher fields by γ ∝ H 1 . Here, we argue that, within the two-band theory of superconductivity, an inflection point may occur if the interband coupling is dominant.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

First neutral beam injection experiments on KSTAR tokamak

The first neutral beam (NB) injection system of the Korea Superconducting Tokamak Advanced Research (KSTAR) tokamak was partially completed in 2010 with only 1/3 of its full design capability, and NB heating experiments were carried out during the 2010 KSTAR operation campaign. The ion source is composed of a JAEA bucket plasma generator and a KAERI large multi-aperture accelerator assembly, which is designed to deliver a 1.5 MW, NB power of deuterium at 95 keV. Before the beam injection experiments, discharge, and beam extraction characteristics of the ion source were investigated. The ion source has good beam optics in a broad range of beam perveance. The optimum perveance is 1.1-1.3 {mu}P, and the minimum beam divergence angle measured by the Doppler shift spectroscopy is 0.8 deg. The ion species ratio is D{sup +}:D{sub 2}{sup +}:D{sub 3}{sup +}= 75:20:5 at beam current density of 85 mA/cm{sup 2}. The arc efficiency is more than 1.0 A/kW. In the 2010 KSTAR campaign, a deuterium NB power of 0.7-1.5 MW was successfully injected into the KSTAR plasma with a beam energy of 70-90 keV. L-H transitions were observed within a wide range of beam powers relative to a threshold value. The edge pedestal formation in the T{sub i} and T{sub e} profiles was verified through CES and electron cyclotron emission diagnostics. In every deuterium NB injection, a burst of D-D neutrons was recorded, and increases in the ion temperature and plasma stored energy were found.

43 PARTICLE ACCELERATORS↗

A particle-in-cell Monte Carlo code for electron beam ion source simulation

FAR-TECH, Inc., has developed a particle-in-cell Monte Carlo code (EBIS-PIC) to model ion motions in an electron beam ion source (EBIS). First, a steady state electron beam is simulated by the PBGUNS code (see http://far-tech.com/pbguns/index.html). Then, the injected primary ions and the ions from the background neutral gas are tracked in the trapping region using Monte Carlo method. Atomic collisions and Coulomb collisions are included in the EBIS-PIC model. The space charge potential is updated by solving the Poisson equation each time step. The preliminary simulation results are presented and compared with BNL electron beam test stand (EBTS) fast trapping experiments.

43 PARTICLE ACCELERATORS↗

Theoretical And Experimental Studies Of The Effects Of Rapid Thermal Annealing In GaAs/AlGaAs Quantum Dots Grown By Droplet Epitaxy

We fabricated low-density GaAs/AlGaAs quantum dots for single photon source by droplet epitaxy. We investigated the emission energies of the dots and underlying superlattice by using photoluminescence and cathodoluminescence measurements. By forming a mesa etched structure, we distinguished the transitions from the superlattice and the dots. And we calculated the diffusion length in this system from the peak shift of the superlattice, and applied the diffusion to the dots to investigate the emission energy shift of the QDs.z

36 MATERIALS SCIENCE↗

Excitation Power Dependence Of Photoluminescence From GaAs Quantum Dot Prepared By Droplet Epitaxy Method

GaAs quantum dot (QD) was grown by droplet epitaxy (DE) method and the excitation power dependence of photoluminescence (PL) were carried out. To investigate the effect of annealing temperature on QDs optical properties, the two step RTA process was carried out in a various temperature range from 800 to 1000 deg. C. As the thermal annealing temperature increases, the PL peak position is blue-shifted due to the change of the composition and size distribution of QDs, and the highest PL intensity is observed at the sample annealed at 900 deg. C. The integrated PL intensity (I{sub PL}) is plotted against the excitation density in a log-log scale and the slope was calculated.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Micro-Photoluminescence Characterization of Low Density Droplet GaAs Quantum Dots for Single Photon Sources

The GaAs quantum dots in AlGaAs barriers were grown by droplet epitaxy, emitting around 700 nm in wavelength which is compatible with low cost Si based detectors. The excitation power dependent and time resolved micro-photoluminescence measurements identified optical characteristics of exciton and biexciton states which are attributed to good quantum confinements in GaAs QDs.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

NEW YOUNG STAR CANDIDATES IN CG4 AND Sa101

The CG4 and Sa101 regions together cover a region of {approx}0.5 deg{sup 2} in the vicinity of a 'cometary globule' that is part of the Gum Nebula. There are seven previously identified young stars in this region; we have searched for new young stars using mid- and far-infrared data (3.6-70 {mu}m) from the Spitzer Space Telescope, combined with ground-based optical data and near-infrared data from the Two Micron All Sky Survey. We find infrared excesses in all six of the previously identified young stars in our maps and identify 16 more candidate young stars based on apparent infrared excesses. Most (73%) of the new young stars are Class II objects. There is a tighter grouping of young stars and young star candidates in the Sa101 region, in contrast to the CG4 region, where there are fewer young stars and young star candidates, and they are more dispersed. Few likely young objects are found in the 'fingers' of the dust being disturbed by the ionization front from the heart of the Gum Nebula.

79 ASTRONOMY AND ASTROPHYSICS↗

Infinitely high selective inductively coupled plasma etching of an indium tin oxide binary mask structure for extreme ultraviolet lithography

Currently, extreme ultraviolet lithography (EUVL) is being investigated for next generation lithography. Among the core EUVL technologies, mask fabrication is of considerable importance due to the use of new reflective optics with a completely different configuration than those of conventional photolithography. This study investigated the etching properties of indium tin oxide (ITO) binary mask materials for EUVL, such as ITO (absorber layer), Ru (capping/etch-stop layer), and a Mo-Si multilayer (reflective layer), by varying the Cl{sub 2}/Ar gas flow ratio, dc self-bias voltage (V{sub dc}), and etch time in inductively coupled plasmas. The ITO absorber layer needs to be etched with no loss in the Ru layer on the Mo-Si multilayer for fabrication of the EUVL ITO binary mask structure proposed here. The ITO layer could be etched with an infinitely high etch selectivity over the Ru etch-stop layer in Cl{sub 2}/Ar plasma even with a very high overetch time.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A Resonant Cavity Approach to Non-Invasive, Pulse-to-Pulse EmittanceMeasurement

We present a resonant cavity approach for non-invasive, pulse-to-pulse, beam emittance measurements of non-circular multi-bunch beams. In a resonant cavity, desired field components can be enhanced up to Q{sub L{lambda}}/{pi}, where Q{sub L{lambda}} is the loaded quality factor of the resonant mode {lambda}, when the cavity resonant mode matches the bunch frequency of a bunch-train beam pulse. In particular, a quad-cavity, with its quadrupole mode (TM{sub 220} for rectangular cavities) at beam operating frequency, rotated 45{sup o} with respect to the beamline, extracts the beam quadrupole moment exclusively, utilizing the symmetry of the cavity and some simple networks to suppress common modes. Six successive beam quadrupole moment measurements, performed at different betatron phases in a linear transport system determine the beam emittance, i.e. the beam size and shape in the beam's phase space, if the beam current and position at these points are known. In the presence of x-y beam coupling, ten measurements are required. One measurement alone provides the rms-beam size of a large aspect ratio beam. The resolution for such a measurement of rms-beam size with the rectangular quad-cavity monitor presented in this article is estimated to be on the order of ten microns. A prototype quad-cavity was fabricated and preliminary beam tests were performed at the Next Linear Collider Test Accelerator (NLCTA) at the Stanford Linear Accelerator Center (SLAC). Results were mainly limited by beam jitter and uncertainty in the beam position measurement at the cavity location. This motivated the development of a position-emittance integrated monitor.

43 PARTICLE ACCELERATORS↗

Simulation of parameter scaling in electron cyclotron resonance ion source plasmas using the GEM code

Although heating power and gas pressure are two of the two of primary experimental ''knobs'' available to users of electron cyclotron resonance ion sources, there is still no clear understanding of how they interact in order to provide optimal plasma conditions. FAR-TECH, Inc. has performed a series of simulations with its generalized electron cyclotron resonance ion source model in which the power and pressure were varied over a wide range. Analysis of the numerical data produces scaling laws that predict the plasma parameters as a function of the power and pressure. These scaling laws are in general agreement with experimental data.

43 PARTICLE ACCELERATORS↗

Integrated modeling of electron cyclotron resonance ion sources and charge breeders with GEM, MCBC, and IonEx

A numerical toolset to help in understanding physical processes in the electron cyclotron resonance charge breeder (ECRCB) and further to help optimization and design of current and future machines is presented. The toolset consists of three modules (Monte Carlo charge breeding code, generalized electron cyclotron resonance ion source modeling, and ion extraction), each modeling different processes occurring in the ECRCB from beam injection to extraction. The toolset provides qualitative study, such as parameter studies, and scaling of the operation, and physical understanding in the ECRCB. The methodology and a sample integrated modeling are presented.

43 PARTICLE ACCELERATORS↗

IONEX: A meshfree ion extraction code based on ''particle in cloud of points'' concept

Ion Extraction (IONEX) is an ion extraction modeling code, developed at FAR-TECH, Inc., based on the meshless particle-in-cloud-of-points concept. IONEX self-consistently solves motion equations for ions and Poisson's equation for the electrostatic field, assuming a Boltzmann distribution for the electrons. IONEX is capable of handling multiple species and is graphical user interface-driven. The two-dimensional version is benchmarked with IGUN. The basic algorithm and sample runs are presented.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Simulation of charge breeding of rubidium using Monte Carlo charge breeding code and generalized ECRIS model

A Monte Carlo charge breeding code (MCBC) is being developed by FAR-TECH, Inc. to model the capture and charge breeding of 1+ ion beam in an electron cyclotron resonance ion source (ECRIS) device. The ECRIS plasma is simulated using the generalized ECRIS model which has two choices of boundary settings, free boundary condition and Bohm condition. The charge state distribution of the extracted beam ions is calculated by solving the steady state ion continuity equations where the profiles of the captured ions are used as source terms. MCBC simulations of the charge breeding of Rb+ showed good agreement with recent charge breeding experiments at Argonne National Laboratory (ANL). MCBC correctly predicted the peak of highly charged ion state outputs under free boundary condition and similar charge state distribution width but a lower peak charge state under the Bohm condition. The comparisons between the simulation results and ANL experimental measurements are presented and discussed.

43 PARTICLE ACCELERATORS↗

Highly selective etching of silicon nitride to physical-vapor-deposited a-C mask in dual-frequency capacitively coupled CH{sub 2}F{sub 2}/H{sub 2} plasmas

A multilevel resist (MLR) structure can be fabricated based on a very thin amorphous carbon (a-C) layer ( congruent with 80 nm) and Si{sub 3}N{sub 4} hard-mask layer ( congruent with 300 nm). The authors investigated the selective etching of the Si{sub 3}N{sub 4} layer using a physical-vapor-deposited (PVD) a-C mask in a dual-frequency superimposed capacitively coupled plasma etcher by varying the process parameters in the CH{sub 2}F{sub 2}/H{sub 2}/Ar plasmas, viz., the etch gas flow ratio, high-frequency source power (P{sub HF}), and low-frequency source power (P{sub LF}). They found that under certain etch conditions they obtain infinitely high etch selectivities of the Si{sub 3}N{sub 4} layers to the PVD a-C on both the blanket and patterned wafers. The etch gas flow ratio played a critical role in determining the process window for infinitely high Si{sub 3}N{sub 4}/PVD a-C etch selectivity because of the change in the degree of polymerization. The etch results of a patterned ArF photoresisit/bottom antireflective coating/SiO{sub x}/PVD a-C/Si{sub 3}N{sub 4} MLR structure supported the idea of using a very thin PVD a-C layer as an etch-mask layer for the Si{sub 3}N{sub 4} hard-mask pattern with a pattern width of congruent with 80 nm and high aspect ratio of congruent with 5.

36 MATERIALS SCIENCE↗

Deep level transient spectroscopy study of energy levels in InAs/GaAs self-assembled quantum dots

The energy states in InAs/GaAs self-assembled QD system were measured and analyzed by using capacitance-voltage and deep level transient spectroscopy methods with varying the applied biases and the filling pulse widths. The activation energies of the QD signals were shifted from 0.07 to 0.60 eV by changing the measurement biases, and then these results represent that the QD has many kind of confined energy levels. From the DLTS measurements with varying the filling pulse widths, it was confirmed that the QD has band-like interacting energy levels.

36 MATERIALS SCIENCE↗