Search NASA⌕ Search

Engineering topics

Kim, J

Publications and source records attributed to Kim, J.

At least 145 records · Page 8

Ti-Doped Indium Tin Oxide Thin Films for Transparent Field-Effect Transistors: Control of Charge-Carrier Density and Crystalline Structure

Indium tin oxide (ITO) films are representative transparent conducting oxide media for organic light-emitting diodes, liquid crystal displays, and solar cell applications. Extending the utility of ITO films from passive electrodes to active channel layers in transparent field-effect transistors (FETs), however, has been largely limited because of the materials' high carrier density (>1 x 10{sup 20} cm{sup 03}), wide band gap, and polycrystalline structure. Here, we demonstrate that control over the cation composition in ITO-based oxide films via solid doping of titanium (Ti) can optimize the carrier concentration and suppress film crystallization. On 120 nm thick SiO{sub 2}/Mo (200 nm)/glass substrates, transparent n-type FETs prepared with 4 at % Ti-doped ITO films and fabricated via the cosputtering of ITO and TiO{sub 2} exhibited high electron mobilities of 13.4 cm{sup 2} V{sup -1} s{sup -1}, a low subthreshold gate swing of 0.25 V decade{sup -1}, and a high I{sub on}/I{sub off} ratio of >1 x 10{sup 8}.

36 MATERIALS SCIENCE↗

Hard X-ray Nano Patterning using a Sectioned Multilayer

We report a hard x-ray patterning capable of drawing lines with a width below 100 nm using x-rays at 0.165 nm. A specially prepared mask based on multilayer growth technology was used as an x-ray mask effectively. The x-ray Talbot effect in near field was investigated and utilized in the patterning. Since multilayers with a few nanometer layer spacing are readily available, the proposed hard x-ray nano patterning, free of the limit imposed by the Rayleigh criterion in optical range, can potentially be an ultimate optical lithography technique.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Interfacial Nanostructure Induced Spin-reorientation Transition in Ni/Fe/Ni/W(110)

We investigated the mechanism of the spin-reorientation transition (SRT) in the Ni/Fe/Ni/W(110) system using in situ low-energy electron microscopy, x-ray magnetic circular dichroism measurements, and first principles electronic structure calculations. We discovered that the growth of Fe on a flat Ni film on a W (110) crystal resulted in the formation of nanosized particles, instead of a uniform monolayer of Fe as commonly assumed. This interfacial nanostructure leads to a change of the system's dimensionality from two-dimensional- to three-dimensional-like, which simultaneously weakens the dipolar interaction and enhances the spin-orbit coupling in the system and drives the observed SRT.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Coupled Magnetic Cycloids in Multiferroic TbMnO3 and Eu3/4Y1/4MnO3

Based on the detailed Mn L{sub 2,3}-edge x-ray resonant scattering results, we report a new complexity in the magnetic order of multiferroic orthomangnites, which has been considered as the simple A-type cycloid order inducing ferroelectricity. The Dzyaloshinskii-Moriya interaction involved in the orthorhombic distortion brings on F-type canting from the A type, and the ordering type becomes the off-phase synchronized bc cycloid in TbMnO{sub 3} or the tilted antiphase ab cycloid in Eu{sub 3/4}Y{sub 1/4}MnO{sub 3}. The F-type canting is responsible for the magnetic field-driven multiferroicity to weak ferromagnetism transition.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Revealing the Dual Nature of Magnetism in Iron Pnictides and Iron Chalcogenides Using X-ray Emission Spectroscopy

We report a Fe K{beta} x-ray emission spectroscopy study of local magnetic moments in various iron-based superconductors in their paramagnetic phases. Local magnetic moments are found in all samples studied: PrFeAsO, Ba(Fe,Co){sub 2}As{sub 2}, LiFeAs, Fe{sub 1+x}(Te,Se), and A{sub 2}Fe{sub 4}Se{sub 5} (where A = K, Rb, and Cs). The moment size is independent of temperature or carrier concentration but varies significantly across different families. Specifically, all iron pnictide samples have local moments of about 1 {micro}B/Fe, while FeTe and K{sub 2}Fe{sub 4}Se{sub 5} families have much larger local moments of {approx}2 {micro}B/Fe and {approx}3.3 {micro}B/Fe, respectively. Our results illustrate the importance of multiorbital physics in describing magnetism of these compounds.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Impact of plug-in hybrid electric vehicles on power systems with demand response and wind power.

This paper uses a new unit commitment model which can simulate the interactions among plug-in hybrid electric vehicles (PHEVs), wind power, and demand response (DR). Four PHEV charging scenarios are simulated for the Illinois power system: (1) unconstrained charging, (2) 3-hour delayed constrained charging, (3) smart charging, and (4) smart charging with DR. The PHEV charging is assumed to be optimally controlled by the system operator in the latter two scenarios, along with load shifting and shaving enabled by DR programs. The simulation results show that optimally dispatching the PHEV charging load can significantly reduce the total operating cost of the system. With DR programs in place, the operating cost can be further reduced.

17 WIND ENERGY↗

Development of a plasma generator for a long pulse ion source for neutral beam injectors

A plasma generator for a long pulse H{sup +}/D{sup +} ion source has been developed. The plasma generator was designed to produce 65 A H{sup +}/D{sup +} beams at an energy of 120 keV from an ion extraction area of 12 cm in width and 45 cm in length. Configuration of the plasma generator is a multi-cusp bucket type with SmCo permanent magnets. Dimension of a plasma chamber is 25 cm in width, 59 cm in length, and 32.5 cm in depth. The plasma generator was designed and fabricated at Japan Atomic Energy Agency. Source plasma generation and beam extraction tests for hydrogen coupling with an accelerator of the KSTAR ion source have been performed at the KSTAR neutral beam test stand under the agreement of Japan-Korea collaborative experiment. Spatial uniformity of the source plasma at the extraction region was measured using Langmuir probes and {+-}7% of the deviation from an averaged ion saturation current density was obtained. A long pulse test of the plasma generation up to 200 s with an arc discharge power of 70 kW has been successfully demonstrated. The arc discharge power satisfies the requirement of the beam production for the KSTAR NBI. A 70 keV, 41 A, 5 s hydrogen ion beam has been extracted with a high arc efficiency of 0.9 -1.1 A/kW at a beam extraction experiment. A deuteron yield of 77% was measured even at a low beam current density of 73 mA/cm{sup 2}.

43 PARTICLE ACCELERATORS↗

Charge-transfer and Mott-Hubbard Excitations in FeBo{sub 3} : Fe K-edge resonant Inelastic x-ray scattering study.

Momentum-resolved resonant inelastic x-ray scattering (RIXS) spectroscopy has been carried out successfully at the Fe K-edge for the first time. The RIXS spectra of a FeBO{sub 3} single crystal reveal a wealth of information on {approx} 1-10 eV electronic excitations. The IXS signal resonates when the incident photon energy approaches the pre-edge (1s{sup -}-3d) and the main-edge (1s{sup -}-4p) of the Fe K-edge absorption spectrum. The RIXS spectra measured at the pre-edge and the main-edge show quantitatively different dependences on the incident photon energy, momentum transfer, photon polarization, and temperature. We present a multielectron analysis of the Mott-Hubbard (MH) and charge transfer (CT) excitations, and calculate their energies. Electronic excitations observed in the pre-edge and main-edge RIXS spectra are interpreted as MH and CT excitations, respectively. We propose the electronic structure around the chemical potential in FeBO{sub 3} based on the experimental data.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Pearson's random walk in the space of the CMB phases: Evidence for parity asymmetry

The temperature fluctuations of the cosmic microwave background (CMB) are supposed to be distributed randomly in both magnitude and phase, following to the simplest model of inflation. In this paper, we look at the odd and even multipoles of the spherical harmonic decomposition of the CMB, and the different characteristics of these, giving rise to a parity asymmetry. We compare the even and odd multipoles in the CMB power spectrum, and also the even and odd mean angles. We find for the multipoles of the power spectrum that there is power excess in odd multipoles, compared to even ones, meaning that we have a parity asymmetry. Further, for the phases, we present a random walk for the mean angles, and find a significant separation for even/odd mean angles, especially so for galactic coordinates. This is further tested and confirmed with a directional parity test, comparing the parity asymmetry in galactic and ecliptic coordinates.

97 MATHEMATICS AND COMPUTING↗

Electronic Structure of Doped Lanthanum Cuprates Studied with Resonant Inelastic X-Ray Scattering

We report a comprehensive Cu K-edge resonant inelastic x-ray scattering (RIXS) investigation of La{sub 2-x}Sr{sub x}CuO{sub 4} (LSCO) for 0 {le} x {le} 0.35, stripe-ordered La{sub 1.875}Ba{sub 0.125}CuO{sub 4} (LBCO), and La{sub 2}Cu{sub 0.96}Ni{sub 0.04}O{sub 4} (LCNO) crystals. The RIXS spectra measured at three high-symmetry momentum-transfer (q) positions are compared as a function of doping and for the different dopants. The spectra in the energy range 1-6 eV can be described with three broad peaks, which evolve systematically with increased doping. The most systematic trend was observed for q = ({pi},0) corresponding to the zone boundary. As hole doping increased, the spectral weight transfer from high energies to low energies is nearly linear with x at this q. We interpret the peaks as interband transitions in the context of existing band models for this system, assigning them to Zhang-Rice band {yields} upper Hubbard band, lower-lying band {yields} upper Hubbard band, and lower-lying band {yields} Zhang-Rice band transitions. The spectrum of stripe-ordered LBCO was also measured, and found to be identical to the correspondingly doped LSCO, except for a relative enhancement of the near-infrared peak intensity at {approx}1.5-1.7 eV. The temperature dependence of this near-infrared peak in LBCO was more pronounced than for other parts of the spectrum, continuously decreasing in intensity as the temperature was raised from 25 to 300 K. Finally, we find that 4% Ni substitution in the Cu site has a similar effect on the spectra as does Sr substitution in the La site.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

KSTAR Equilibrium Operating Space and Projected Stabilization at High Normalized Beta

Along with an expanded evaluation of the equilibrium operating space of the Korea Superconducting Tokamak Advanced Research, KSTAR, experimental equilibria of the most recent plasma discharges were reconstructed using the EFIT code. In near-circular plasmas created in 2009, equilibria reached a stored energy of 54 kJ with a maximum plasma current of 0.34 MA. Highly shaped plasmas with near double-null configuration in 2010 achieved H-mode with clear edge localized mode (ELM) activity, and transiently reached a stored energy of up to 257 kJ, elongation of 1.96 and normalized beta of 1.3. The plasma current reached 0.7 MA. Projecting active and passive stabilization of global MHD instabilities for operation above the ideal no-wall beta limit using the designed control hardware was also considered. Kinetic modification of the ideal MHD n = 1 stability criterion was computed by the MISK code on KSTAR theoretical equilibria with a plasma current of 2 MA, internal inductance of 0.7 and normalized beta of 4.0 with simple density, temperature and rotation profiles. The steep edge pressure gradient of this equilibrium resulted in the need for significant plasma toroidal rotation to allow thermal particle kinetic resonances to stabilize the resistive wall mode (RWM). The impact of various materials and electrical connections of the passive stabilizing plates on RWM growth rates was analysed, and copper plates reduced the RWM passive growth rate by a factor of 15 compared with stainless steel plates at a normalized beta of 4.4. Computations of active RWM control using the VALEN code showed that the n = 1 mode can be stabilized at normalized beta near the ideal wall limit via control fields produced by the midplane in-vessel control coils (IVCCs) with as low as 0.83kW control power using ideal control system assumptions. The ELM mitigation potential of the IVCC, examined by evaluating the vacuum island overlap created by resonant magnetic perturbations, was analysed using the TRIP3D code. Using a combination of all IVCCs with dominant n = 2 field and upper/lower coils in an even parity configuration, a Chirikov parameter near unity at normalized poloidal flux 0.83, an empirically determined condition for ELM mitigation in DIII-D, was generated in theoretical high-beta equilibria. Chirikov profile optimization was addressed in terms of coil parity and safety factor profile.

Park, Y S↗

BK using HYP-smeared staggered fermions in Nf = 2 + 1 unquenched QCD

We present results for the kaon mixing parameter B{sub K} calculated using HYP (hypercubic fat link)-smeared improved staggered fermions on the asqtad lattices generated by the MILC collaboration. We use three lattice spacings (a{approx} 0.12, 0.09 and 0.06 fm), ten different valence-quark masses (m {approx} m{sub s}/10-m{sub s}), and several light sea-quark masses in order to control the continuum and chiral extrapolations. We derive the next-to-leading order staggered chiral perturbation theory (SChPT) results necessary to fit our data, and use these results to do extrapolations based both on SU(2) and SU(3) SChPT. The SU(2) fitting is particularly straightforward because parameters related to taste breaking and matching errors appear only at next-to-next-to-leading order. We match to the continuum renormalization scheme [naive dimensional regularization (NDR)] using one-loop perturbation theory. Our final result is from the SU(2) analysis, with the SU(3) result providing a (less accurate) cross check. We find B{sub K}(NDR, {mu} = 2 GeV) = 0.529 {+-} 0.009 {+-} 0.032 and B{sub K} = B{sub K}(RGI) = 0.724 {+-} 0.012 {+-} 0.043, where the first error is statistical and the second systematic. The error is dominated by the truncation error in the matching factor. Our results are consistent with those obtained using valence domain-wall fermions on lattices generated with asqtad or domain-wall sea quarks.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Use of the Far Infrared Tangential Interferometer/Polarimeter diagnostic for the study of rf driven plasma waves on NSTX

A rf detection system for waves in the 30 MHz range has been constructed for the Far Infrared Tangential Interferometer/Polarimeter on National Spherical Torus Experiment (NSTX). It is aimed at monitoring high frequency density fluctuations driven by 30 MHz high harmonic fast wave fields. The levels of density fluctuations at various radial chords and antenna phase angles can be estimated using the electric field calculated by TORIC code and linearized continuity equation for the electron density. In this paper, the experimental arrangement for the detection of rf signal and preliminary results of simulation will be discussed.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Microwave imaging reflectometry studies for turbulence diagnostics on KSTAR

The first prototype microwave imaging reflectometry (MIR) system [H. Park et al., Rev. Sci. Instrum. 74, 4239 (2004)] clearly demonstrated the shortcomings of conventional reflectometry when the probe beam encountered a large amplitude and/or high fluctuation wavenumber at the reflection layer in laboratory tests, the distinctive advantages shown in these tests were not fully realized in the plasma operation. To understand the discrepancies, the MIR system performance has been thoroughly investigated at POSTECH. In this paper, a possible cause of the MIR performance degradation on TEXTOR will be presented together with a concept of multifrequency MIR system design that will be developed for KSTAR.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Comparison of the sputter rates of oxide films relative to the sputter rate of SiO{sub 2}

There is a growing interest in knowing the sputter rates for a wide variety of oxides because of their increasing technological importance in many different applications. To support the needs of users of the Environmental Molecular Sciences Laboratory, a national scientific user facility, as well as our research programs, the authors made a series of measurements of the sputter rates from oxide films that have been grown by oxygen plasma-assisted molecular beam epitaxy, pulsed laser deposition, atomic layer deposition, electrochemical oxidation, or sputter deposition. The sputter rates for these oxide films were determined in comparison with those from thermally grown SiO{sub 2}, a common reference material for sputter rate determination. The film thicknesses and densities for most of these oxide films were measured using x-ray reflectivity. These oxide films were mounted in an x-ray photoelectron or Auger electron spectrometer for sputter rate measurements using argon ion sputtering. Although the primary objective of this work was to determine relative sputter rates at a fixed angle, the measurements also examined (i) the angle dependence of the relative sputter rates, (ii) the energy dependence of the relative sputter rates, and (iii) the extent of ion beam induced reduction for some oxides. Oxide films examined include SiO{sub 2}, Al{sub 2}O{sub 3}, CeO{sub 2}, Cr{sub 2}O{sub 3}, Fe{sub 2}O{sub 3}, HfO{sub 2}, In-Sn oxide, Ta{sub 2}O{sub 5}, TiO{sub 2} (anatase, rutile, and amorphous), and ZnO. The authors found that the sputter rates for the oxides can vary up to a factor of 2 (usually lower) from that observed for SiO{sub 2}. The ratios of sputter rates relative to those of SiO{sub 2} appear to be relatively independent of ion beam energy in the range of 1-4 kV and for incident angles <50 deg. As expected, the extent of ion beam induced reduction of the oxides varies with the sputter angle.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗