Search NASA⌕ Search

Engineering topics

Kim, Jae Jin

Publications and source records attributed to Kim, Jae Jin.

At least 19 records

Entropy-Stabilized Multication Fluorides as a Conversion-Type Cathode for Li-Ion Batteries–Impact of Element Selection

Metal fluorides (e.g., FeF 2 and FeF 3 ) have received attention as conversion-type cathode materials for Li-ion batteries due to their higher theoretical capacity compared to that of common intercalation materials. However, their practical use has been hindered by low round-trip efficiency, voltage hysteresis, and capacity fading. Cation substitution has been proposed to address these challenges, and recent advancements in battery performance involve the introduction of entropy stabilization in an attempt to facilitate reversible conversion reactions by increasing configurational entropy. Building on this concept, high entropy fluorides with five cations were synthesized by using a simple mechanochemical route. In order to examine the impact of element selection, Co 0.2 Cu 0.2 Ni 0.2 Zn 0.2 Fe 0.2 F 2 (HEF-Fe) was compared with Co 0.2 Cu 0.2 Ni 0.2 Zn 0.2 Mg 0.2 F 2 (HEF-Mg), replacing electrochemically inactive Mg with Fe as an active participant in the conversion reaction. Combining electrochemical measurements with first-principles calculations, high-resolution electron microscopy, and synchrotron X-ray analysis, HEFs’ battery performances and conversion reaction mechanisms were investigated in detail. The results highlighted that replacement of Mg with Fe was beneficial, with enhanced capacity, rate capability, and surface stability. In addition, it was found that HEF-Fe showed similar cycle stability without an electrochemically inactive element. In conclusion, these findings provide valuable insights for the design of high entropy multielement fluorides for improved Li-ion battery performance.

25 ENERGY STORAGE↗

Strain-Driven Surface Reactivity in Magnesium-Ion Battery Cathodes

Successful deployment of a Mg-ion battery requires cathodes that can achieve reversible Mg intercalation and high energy density. Recent theoretical and experimental studies indicated that the overall transport is likely limited by sluggish Mg transport at the cathode-electrolyte interface and not Mg diffusion through bulk. Here, in this work, we investigated the surface electrochemical activity of Mg ions by using a spinel-structured manganese oxide thin-film model system and in situ X-ray scattering. In combination with post-mortem microscopy analysis, we found that magnesium insertion was more favorable than subsequent extraction near the surface of the Mg x Mn 2 O 4 film, resulting in overmagnesiation, and eventually amorphization of the surface. This structural irreversibility and high overpotential required for Mg extraction could explain significant voltage hysteresis and Mg surface enrichment previously observed in bulk cathodes. Density functional theory calculations suggested that the tendency for the Mg surface enrichment could be associated with Mg diffusion kinetics, which varies with the strain state evolved due to constrained film volume change during Mg insertion and extraction. Particularly, out-of-plane Mg migration was predicted to be favorable in the tensile strain rather than in the compressive case.

25 ENERGY STORAGE↗

Room-temperature fabrication of garnet-type solid-electrolyte: Optimizing particle size for high ionic conductivity

Dense and uniform Li 6.25 Al 0.25 La 3 Zr 2 O 12 (Al-doped LLZO) solid-electrolyte film of ~24 µm thickness is successfully fabricated by room temperature aerosol deposition (AD) method. The process optimization study revealed that careful control of particle size and morphology is one of critical determinants in the development of a compact AD membrane. Notably, our method facilitated an impressive ionic conductivity of approximately 10 –5 S cm –1 , bypassing the necessity for post-annealing processes, a milestone in itself. However, it is hypothesized that the attained conductivity is somewhat restrained by factors such as smaller grain size and potential surface degradation due to moisture exposure during fabrication, indicating avenues for further research. Looking forward, detailed investigations into the film's microstructure and its impact on transport properties will be a focal point, alongside potential enhancements through post-annealing and particle coating strategies. Finally, this research hints at a promising trajectory for the development of high-efficiency solid-state battery technology.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Influence of electronic transport on electrochemical performance of (Cu,Mn) 3 O 4 solid oxide fuel cell cathodes

Alkaline Earth free spinel oxides provide a potential benefit over Sr-doped perovskite-based materials commonly used as electrodes in high-temperature electrochemical energy conversion devices, e.g., solid oxide fuel cells (SOFCs). Sr-segregation is a known issue leading to performance degradation. In this study, Cu x Mn 3-x O 4 (x = 1, 1.2, and 1.5) porous electrodes were examined as SOFC cathodes using electrochemical impedance spectroscopy to investigate the oxygen reduction reaction (ORR) kinetics in relation to the material's intrinsic conductivity, the extrinsic electrode structure, and the cell test design. Similar to the electronic conducting (La,Sr)MnO 3 SOFC cathodes, the ORR kinetics of Cu x Mn 3-x O 4 spinel electrodes was governed by the oxygen adsorption and diffusion at the particle surface as well as the charge transfer at the triple phase boundaries. The overall electrode polarization resistance was highly dependent on contact density with the metallic current collector, active material particle connectivity, electrode thickness, and the intrinsic electronic materials conductivity. Here, we describe the importance of effective electronic charge transport parallel to the electrode surface in maximizing the electrochemically active electrode volume and enhancing electrode performance. We discuss an approach to optimize cell and electrode design with respect to active materials properties. This aspect is critical to ensure reliable evaluation of new materials, since laboratory-scale button-cells typically exhibit a high degree of electrode microstructure (e.g. porosity, thickness) and electrical contact density variation from sample to sample.

(Cu,Mn)3O4↗

Molecular Beam Epitaxy of Monocrystalline GaAs on Water-Soluble NaCl Thin Films

The goal of this project was to demonstrate the feasibility of employing an epitaxial NaCl thin film as a water-soluble release layer for III-V photovoltaic devices and GaAs substrate reuse. Over the course of this project efforts were focused on: 1) achieving crystalline NaCl thin films on GaAs (100) substrate, 2) exploring the growth parameters for subsequent GaAs on NaCl thin films in effort to improve crystallinity of the semiconductor layer, 3) deposition and removal of single crystalline solar cell devices from the parent substrate, and 4) improving morphology and reducing large scale defects in the removed layers to fabricate a working a solar cell device. There was no previous work on direct integration of GaAs/NaCl/GaAs heterostructures at the time of this study. We used molecular beam epitaxy (MBE) to deposit both the alkali halide salt and subsequent III-V material in the same chamber, with no vacuum break. Single crystalline GaAs films were achieved on NaCl layers through careful tuning of the growth parameters and exposure to the reflection high energy electron diffraction (RHEED) beam. Dissolution of the NaCl layer in water provided rapid release of the semiconductor layer from the substrate. Monocrystalline solar cells were grown on the III-V templates using MBE and dynamic hydride vapor phase epitaxy (HVPE). However, the extended time at elevated temperatures required for the cell growth resulted in large area defects from fusion of the semiconductor overlayer to the substrate, causing shorts in fabricated devices. By changing the way that the template layer was grown, the density of these defects could be reduced. Unfortunately, the defects were not reduced to a level allowing for fabrication of a working device.

14 SOLAR ENERGY↗

GaAs Substrate Recycling Using in-situ Deposited NaCl Layers via Molecular Beam Epitaxy

This work presents an alternative method to conventional III-V substrate recycling methods via growth of NaCl on nearly-lattice matched GaAs (001) substrates. Reflection high energy electron diffraction and transmission electron microscopy confirm an epitaxial relationship between the NaCl layers and the underlying GaAs. If the sample is heated too much prior to GaAs deposition, the NaCl fully desorbs from the surface. The quality of the deposition of GaAs on NaCl ranges from amorphous at low temperature to polycrystalline at intermediate temperatures. Exposure to electron beams during growth results in larger and (001) textured grains. The substrate is separated from the GaAs film in seconds via submersion in water, revealing a substrate surface comparable to the original.

electron beams↗

Facile Electrochemical Mg-Ion Transport in a Defect-Free Spinel Oxide

Inversion, i.e. Mg/Mn antisite disorder, in a spinel oxide simultaneously causes blockage of favorable Mg 2+ migration paths, raising activation barriers for diffusion, and it reduces the number of redox-active metals, limiting the maximum capacity in the spinel. Here, an inversion-free spinel, MgCr 1.5 Mn 0.5 O 4 , was synthesized by exploiting the different intrinsic crystal field stabilization of redox-active Cr and Mn in the form of a solid-solution. The capability of the tailored spinel to reversibly (de)intercalate Mg 2+ at high redox potentials was investigated. The decrease in inversion dramatically lowered the electrochemical overpotential and hysteresis, and enabled utilization of high potentials at ~2.9 V (vs. Mg/Mg 2+ ) upon re-intercalation of Mg 2+ . A combination of characterization techniques reveals that the structural, compositional, and redox changes within the spinel oxide were consistent with the observed electrochemical Mg 2+ activity. Quantification of selective solely to lattice Mg 2+ upon the electrochemical reaction was investigated by monitoring NMR signals in isotope 25 Mg-enriched spinel oxides. Our findings enhance the understanding of Mg 2+ transport within spinel oxide frameworks and provide conclusive evidence for bulk Mg migration in oxide lattices at high redox potentials with minimized electrochemical hysteresis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Structural Changes during the Conversion Reaction of Tungsten Oxide Electrodes with Tailored, Mesoscale Porosity

In-plane tungsten oxide nanostructures, including hexagonally patterned cylinders and holes in a matrix, were fabricated via sequential infiltration synthesis (SIS) on self-assembled block copolymer templates. Using the tailored morphology and porosity of these model electrodes with in situ grazing incidence small angle X-ray scattering, the intrinsic structural change of nanoscale active materials during the conversion reaction of WO 3 + 6Li ↔ W + 3 Li 2 O was investigated at controlled electrochemical conditions. Reversible electrode volume expansion and contraction was observed during lithiation and delithiation cycles, respectively. The potential where electrode’s thickness expansion started was ~1.6 V, which is close to thermodynamically expected one for conversion reaction of WO 3 with lithium (1.65 V). The temporal evolution of the electrode volume at constant electrode potentials revealed high overpotential for bulk lithiation and slow conversion reaction kinetics, despite the tailored porosity of the SIS electrodes. Oxide cylinders showed smaller overall electrode thickness change, likely due to unconstrained lateral volume change, as compared to a matrix with holes. On the other hand, better connectivity and guided volume change of the latter electrode morphology provided improved cycling stability. Additionally, heterogeneity in an electrode, from internal pores and density gradients, was found to aggravate the fragmentation of the electrode during conversion reaction. Insights into oxide conversion reaction kinetics and the relationship between electrode mesostructure and cycling behavior obtained from this study can help guide the more rational design of conversion electrode for high performing batteries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Molecular beam epitaxy of GaAs templates on water soluble NaCl thin films

Expensive III-V substrates are cost limiting for the adoption of many technologies. Consequently, being able to reuse the original substrate is highly desirable. Existing substrate reuse techniques have significant drawbacks, but this work discusses a new method using molecular beam epitaxy deposition of water soluble NaCl thin films on commonly employed (0 0 1) GaAs substrates. Single-crystal GaAs templates are grown on continuous NaCl layers utilizing careful exposure of the NaCl to an in-situ electron beam and a low temperature nucleation layer. The template layers can be quickly removed from the substrate via dissolution of the NaCl. After liftoff, the original wafer shows an increase in rms surface roughness of only 0.2 nm.

14 SOLAR ENERGY↗

Understanding the Solid-State Electrode–Electrolyte Interface of a Model System Using First-Principles Statistical Mechanics and Thin-Film X-ray Characterization

Intermixing of atomic species at the electrode-electrolyte boundaries can impact the properties of the interfaces in solid-state batteries. Herein, this work uses first-principles statistical mechanics along with experimental characterization to understand intermixing at the electrode-electrolyte interface. For the model presented in this work, lithium manganese oxide (LiMn 2 O 4 , LMO) and lithium lanthanum titanate (Li 3x La 2/3-x TiO 3 , LLTO) are employed as the cathode and electrolyte, respectively. The results of the computational work show that Ti-Mn intermixing at the interface is significant at synthesis temperatures. The experimental results in this work find that, at some critical temperatures between 600 and 700 degrees C for material preparation, the interface of LLTO-LMO becomes blurred. Calculations predict that the interface is unstable with regard to Ti-Mn intermixing starting at 0 K, suggesting that the critical temperature found in the experiment is related to kinetics. The work overall suggests that, in designing a solid-state battery, the fundamental reactions such as intermixing need to be considered.

25 ENERGY STORAGE↗

Tailoring Interfaces in Solid-State Batteries Using Interfacial Thermochemistry and Band Alignment

Solid-state lithium ion batteries have enhanced thermal stability compared to batteries using liquid electrolytes. Although their practical implementation is limited by undesired side reactions between the electrode and electrolyte, different modification strategies have been proposed to stabilize these reactive interfaces. These approaches have been primarily based upon bulk materials properties, however, which may not necessarily be representative of the chemistry at the solid/solid interface. In this work, first principles calculations and X-ray scattering experiments are used to elucidate molecular-level reactivity and develop design principles for tailored interfaces based on surface and interfacial properties. Because of its well-known instability, the interface between the Li metal anode and the lithium lanthanum titanate (LLTO) solid electrolyte is applied as a model system. Density functional theory calculations are used to describe bulk, surface, and interfacial thermochemistry of the Li/LLTO system, and interfacial reconstruction is probed using ab initio molecular dynamics. These simulations of the Li/LLTO interface demonstrate facile decomposition concomitant with reduction of Ti 4+ ions. Based on further insights from computational analysis of the surface band edge positions, La 2 O 3 is proposed as an interlayer coating and is shown to provide an energetic barrier for interfacial charge transfer and decomposition reactions from X-ray reflectivity measurements and theoretical calculations. The findings in this work suggest that design strategies based on surface and interfacial properties can be used to kinetically stabilize electrode/electrolyte interfaces in solid-state batteries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Molecular Design of a Highly Stable Single-Ion Conducting Polymer Gel Electrolyte

Single-ion conducting (SIC) polymer electrolytes with a high Li transference number ( t Li + ) have shown the capability to enable enhanced battery performance and safety by avoiding liquid–electrolyte leakage and suppressing Li dendrite formation. However, issues of insufficient ionic conductivity, low electrochemical stability, and poor polymer/electrode interfacial contact have greatly hindered their commercial use. In this work, a Li-containing boron-centered fluorinated SIC polymer gel electrolyte (LiBFSIE) was rationally designed to achieve a high t Li + and high electrochemical stability. Owing to the low dissociation energy of the boron-centered anion and Li + , the as-prepared LiBFSIE exhibited an ionic conductivity of 2 × 10 –4 S/cm at 35 °C, which is exclusively contributed by Li ions owing to a high t Li + of 0.93. Both simulation and experimental approaches were applied to investigate the ion diffusion and concentration gradient in the LiBFSIE and non-cross-linked dual-ion systems. Typical rectangular Li stripping/plating voltage profiles demonstrated the uniform Li deposition assisted by LiBFSIE. The interfacial contact and electrolyte infiltration were further optimized with an in situ UV–vis-initiated polymerization method together with the electrode materials. By virtue of the high electrochemical stability of LiBFSIE, the cells achieved a promising average Coulombic efficiency of 99.95% over 200 cycles, which is higher than that of liquid–electrolyte-based cells. No obvious capacity fading was observed, indicating the long-term stability of LiBFSIE for lithium metal batteries.

36 MATERIALS SCIENCE↗

Frequency-based detection of chemical expansion dynamics in thin films

Current techniques for measuring chemical expansion in thin film structures are too slow, too imprecise, or require synchrotrons. In contrast, nanoscale electrochemomechanical spectroscopy (NECS) can be used to make nanoscale measurements at time scales of seconds with simple contact or non-contact sensors. In a NECS measurement, a sample, such as thin-film oxide structure, is subjected to a temporally modulated stimulus, such as a sinusoidally alternating voltage. The stimulus causes the sample to expand, contract, deflect, or otherwise deform. A sensor, such as a contact probe or optical sensor, produces an electrical signal in response to this deformation that is correlated with the temporal modulation of the stimulus. Because the stimulus and deformation are correlated, the temporal modulation of the stimulus can be used to filter the deformation signal produced by the sensor, producing a precise, sensitive measurement of the deformation.

36 MATERIALS SCIENCE↗

Mechanistic Understanding of Tungsten Oxide In-Plane Nanostructure Growth via Sequential Infiltration Synthesis

Tungsten oxide (WO3-x) nanostructures with hexagonal in-plane arrangements were fabricated by sequential infiltration synthesis (SIS), using the selective interaction of gas phase precursors with functional groups in one domain of a block copolymer (BCP) self-assembled template. Such structures are highly desirable for various practical applications and as model systems for fundamental studies. The nanostructures were characterized by cross-sectional scanning electron microscopy, grazing-incidence small/wide-angle X-ray scattering (GISAXS/GIWAXS), and X-ray absorption near edge structure (XANES) measurements at each stage during the SIS process and subsequent thermal treatments, to provide a comprehensive picture of their evolution in morphology, crystallography and electronic structure. In particular, we discuss the critical role of SIS Al2O3 seeds toward modifying the chemical affinity and free volume in a polymer for subsequent infiltration of gas phase precursors. The insights into SIS growth obtained from this study are valuable to the design and fabrication of a wide range of targeted nanostructures.

Kim, Jae Jin↗

Mechanism of Zn Insertion into Nanostructured δ-MnO 2 : A Nonaqueous Rechargeable Zn Metal Battery

Unlike the more established lithium-ion based energy storage chemistries, the complex intercalation chemistry of multivalent cations in a host lattice is not well understood, especially the relationship between the intercalating species solution chemistry and the prevalence and type of side reactions. Among multivalent metals, a promising model system can be based on nonaqueous Zn2+ ion chemistry. Several examples of these systems support the use of a Zn metal anode, and reversible intercalation cathodes have been reported. This study utilizes a combination of analytical tools to probe the chemistry of a nanostructured delta-MnO2 cathode in association with a nonaqueous acetonitrile-Zn(TFSI)(2) electrolyte and a Zn metal anode. As many of the issues related to understanding a multivalent battery relate to the electrolyte electrode interface, the high surface area of a nanostructured cathode provides a significant interface between the electrolyte and cathode host that maximizes the spectroscopic signal of any side reactions or minor mechanistic pathways. Numerous factors affecting capacity fade and issues associated with the second phase formation including Mn dissolution in heavily cycled Zn/delta-MnO2 cells are presented including dramatic mechanistic differences in the storage mechanism of this couple when compared to similar aqueous electrolytes are noted.

25 ENERGY STORAGE↗