Search NASA⌕ Search

Engineering topics

Kim, Ju-Myung

Publications and source records attributed to Kim, Ju-Myung.

8 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Extending Calendar Life of Si-Based Lithium-Ion Batteries by a Localized High Concentration Electrolyte

Silicon (Si) is one of the most promising anode materials for the next generation lithium-ion batteries (LIBs). Although significant progresses have been made on the cycle life of Si-based LIBs, their calendar-life is still far less than those required for electrical vehicle applications. Here, in this work, the fundamental mechanisms behind the limited calendar life of Si-LIBs have been investigated. It is found that the unstable interphase layers formed on electrodes during the formation/cycling of batteries using conventional electrolyte with fluoroethylene carbonate (FEC) additive are responsible for the rapid impedance-increase of Si-LIBs during storage at elevated temperature (55°C). By using an FEC-free localized high concentration electrolyte (lithium bis(fluorosulfonyl)imide:ethyl propionate:ethylene carbonate:1,1,2,2-tetrafluoroethyl-2,2,3,3-tetrafluoropropyl ether (1:2.8:0.2:1 by mol.) with 1 wt.% lithium difluorophosphate), stable interphase layers formed on electrodes can effectively block the crosstalk between cathode and anode, minimize the impedance increase of Si||LiNi 0.6 Mn 0.2 Co 0.2 (NMC622) batteries during storage at elevated temperature (55°C), therefore largely improve their calendar life. Si||NMC622 batteries using this electrolyte also demonstrated a high-capacity retention of ~92.4% after 500 cycles at 45°C with well-preserved electrode structure. Hence, this novel electrolyte is a good candidate to extend the cycling life and calendar life of Si-LIBs.

25 ENERGY STORAGE↗
DOE OSTI2024

Tailoring Solvation Solvent in Localized High-Concentration Electrolytes for Lithium||Sulfurized Polyacrylonitrile

Sulfurized polyacrylonitrile (SPAN) is a promising cathode material for lithium-sulfur (Li-S) batteries due to its significantly reduced polysulfide (PS) dissolution compared to the elemental S cathode. Although conventional carbonate-based electrolytes is stable with SPAN electrodes, it is less stable with Li metal anode (LMA). Recently, localized high-concentration electrolytes (LHCEs) have been developed to improve the stability of LMA. Here, we report a new strategy to further improve the performance of LI||SPAN batteries by replacing the conventional solvating solvent 1,2-dimethoxyethane (DME) in the LHCE with a new solvating solvent, 1,2-diethoxyethane (DEE), the new LHCEs exhibits less reactivity against Li 2 S 2 , alleviates PS dissolution, forms a better cathode-electrolyte interphase layer on the SPAN, and enhances structure reversibility even at elevated temperature (ET, 45°C). With the same salt and diluent as in other LHCEs, the LHCE with DEE leads to better performance in Li||SPAN batteries (with 82.9% capacity retention after 300 cycles at ET), preservation of SPAN cathode structure, and suppression of the volume change of LMA. The similar strategy on tailoring the solvating solvents in LHCEs can also be used in other rechargeable batteries to improve their performances.

1,2-diethoxyethane↗
DOE OSTI2024

Three-Dimensional Polymeric-Scaffold-Based Current Collector for a Lithium Metal Anode toward High-Energy-Density Batteries

Here, the practical applications of high-energy-density rechargeable lithium (Li) metal batteries (LMBs) have been impeded by the intrinsic issues of the Li metal anode (LMA) including high reactivity with electrolyte and dendritic formation. Conventional LMAs, which have the "hostless" feature consisting of a Li layer on a two-dimensional copper (Cu) foil as a current collector, led to additional loss in specific energy density, since Cu is a nonfaradaic heavy metal, bringing formidable areal capacity loss. To address these problems, a heat-treated three-dimensional-structured Cu-coated polyimide (HT-Cu@PI) membrane is designed and fabricated as a current collector. Benefiting from this unique material/structure, it enables not only better electrochemically deposited Li by a uniform/continuous Li-ion transport pathway but also a significant increase in the gravimetric/volumetric energy densities of LMBs by allowing more Li deposition in a fixed weight/volume. Therefore, this new LMA structure will accelerate the practical application of high-energy-density LMBs.

25 ENERGY STORAGE↗
DOE OSTI2023

Unraveling the convoluted and dynamic interphasial mechanisms on Li metal anode

Accurate understanding of the chemistry of solid-electrolyte interphase (SEI) is key to developing new electrolytes for high-energy batteries using lithium metal (Li-0) anodes(1). SEI is generally believed to be formed by the reactions between Li-0 and electrolyte(2,3). However, our new study shows this is not the whole story. Through synchrotron-based X-ray diffraction and pair distribution function analysis, we reveal a much more convoluted formation mechanism of SEI, which receives considerable contributions from electrolyte, cathode, moisture and native surface species on Li-0, with highly dynamic nature during cycling. Using isotope labelling, we traced the origin of LiH to electrolyte solvent, moisture and a new source: the native surface species (LiOH) on pristine Li-0. When lithium accessibility is very limited as in the case of anode-free cells, LiOH develops into plate-shaped large crystals during cycling. Alternatively, when the lithium source is abundant, as in the case of Li||NMC811 cells, LiOH reacts with Li-0 to form LiH and Li2O. While the desired anion-derived LiF-rich SEI is typically found in the concentrated electrolytes or their derivatives, we found it can also be formed in low-concentration electrolyte via the crosstalk effect, emphasizing the importance of formation cycle protocol and opening up opportunities for low-cost electrolyte development.

Polzin, Bryant J.↗
DOE OSTI2022

Redox-homogeneous, gel electrolyte-embedded high-mass-loading cathodes for high-energy lithium metal batteries

Lithium metal batteries have higher theoretical energy than their Li-ion counterparts, where graphite is used at the anode. However, one of the main stumbling blocks in developing practical Li metal batteries is the lack of cathodes with high-mass-loading capable of delivering highly reversible redox reactions. To overcome this issue, here we report an electrode structure that incorporates a UV-cured non-aqueous gel electrolyte and a cathode where the LiNi 0.8 Co 0.1 Mn 0.1 O 2 active material is contained in an electron-conductive matrix produced via simultaneous electrospinning and electrospraying. This peculiar structure prevents the solvent-drying-triggered non-uniform distribution of electrode components and shortens the time for cell aging while improving the overall redox homogeneity. Moreover, the electron-conductive matrix eliminates the use of the metal current collector. When a cathode with a mass loading of 60 mg cm -2 is coupled with a 100 µm thick Li metal electrode using additional non-aqueous fluorinated electrolyte solution in lab-scale pouch cell configuration, a specific energy and energy density of 321 Wh kg -1 and 772 Wh L -1 (based on the total mass of the cell), respectively, can be delivered in the initial cycle at 0.1 C (i.e., 1.2 mA cm -2 ) and 25 °C.

25 ENERGY STORAGE↗
DOE OSTI2022

Facile Dual-Protection Layer and Advanced Electrolyte Enhancing Performances of Cobalt-free/Nickel-rich Cathodes in Lithium-Ion Batteries

Despite cobalt (Co)-free/nickel (Ni)-rich layered oxides being considered as one of the promising cathode materials due to their high specific capacity, their highly reactive surface is one of the shortcomings that still hinder their practical usages in high-energy-density batteries. Herein, a polyimide/polyvinylpyrrolidone (PI/PVP, denoted as PP) coating layer is demonstrated as dual-protection for LiNi 0.96 Mg 0.02 Ti 0.02 O 2 (NMT) cathode material to suppress surface contamination against moisty air and to prevent unwanted side reactions between cathode and electrolyte during electrochemical cycling. The optimal PP-coated NMT (PP@NMT) preserves a clean surface without generation of lithium (Li) residues, structural degradation, and gas evolution after exposure to air with ~30% humidity for 2 weeks. Contrarily, the exposed bare NMT shows severe contamination, structural shrinkage due to Li loss, and increased gas release during charging. In addition, the exposed PP@NMT significantly enhances the electrochemical performance of graphite (Gr)||NMT cells by decreasing byproducts and maintaining structural stability. Moreover, the exposed PP@NMT achieves a high capacity retention of 86.7% after 500 cycles in Gr||NMT cells using an advanced localized high-concentration electrolyte. Furthermore, this work demonstrates a promising facile approach to the protection of Co-free/Ni-rich layered cathodes for their practical applications even after exposure to moisty air.

25 ENERGY STORAGE↗
DOE OSTI2021

Toward the Practical Use of Cobalt-Free Lithium-Ion Batteries by an Advanced Ether-Based Electrolyte

The criticality of cobalt (Co) has been motivating the quest for Co-free positive electrode materials for building lithium (Li)-ion batteries. However, the Co-free positive electrode materials usually suffer from relatively fast capacity decay when coupled with conventional LiPF 6 -organocarbonates electrolytes. To address this issue, a 1,2-dimethoxyethane (DME) based localized high concentration electrolyte (LHCE) was developed and evaluated in a Co-free Li-ion cell chemistry (Graphite||LiNi 0.96 Mg 0.02 Ti 0.02 O 2 ). Extraordinary capacity retentions were achieved with the LHCE in coin cells (95.3%), single layer pouch cells (79.4%) and high capacity loading double layer pouch cells (70.9 %) after being operated within the voltage range of 2.5-4.4 V for 500 charge/discharge cycles. The capacity retentions of counterpart cells using LiPF6 based conventional electrolyte only reached 61.1%, 57.2% and 59.8%, respectively. Mechanistic studies reveal that the superior electrode/electrolyte interphases formed by the LHCE and the intrinsic chemical stability of the LHCE account for the excellent electrochemical performance in the Co-free Li-ion cells.

25 ENERGY STORAGE↗