Engineering topics
Kim, Jung-Hyun
Publications and source records attributed to Kim, Jung-Hyun.
Garnet solid electrolyte blended LiNi 0.6 Mn 0.2 Co 0.2 O 2 as high-voltage stable cathodes for advanced lithium-ion batteries
Ni-rich LiNi 1-x Co x/2 Mn x/2 O 2 layered materials have been widely adopted as cathodes for current electric vehicles (EVs) due to their high gravimetric and volumetric energy densities. However, their high-voltage instability (e.g., > 4.3 V vsLi ) limited their usable capacities corresponding to about 60 – 70 % of theoretical capacities. The major problems of high-voltage operation stem from instability of Ni 3+/4+ at cathode-electrolyte interphase (CEI) in contact with electrolytes. Here we propose garnet-type Li 6.7 La 3 Zr 1.7 Ta 0.3 O 12 (LLZT) solid-electrolyte-blended LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC) as high-voltage stable cathodes. The LLZT not only passivates the CEI but scavenges protons and moisture in electrolytes. From well-balanced ionic and electronic transport properties, 5 wt% LLZT blended NMC cathodes delivered enhanced electrochemical performances in full-cells. Unlike other complicated coating processes, our proposed solid-electrolyte blending approach can be readily implementable in commercial Li-ion batteries due to its manufacturing friendliness, energy saving, and cost effectiveness.
Phase Stability of Garnet Solid-Electrolyte Interfacing with Various Cathodes in All Solid-State Batteries
Garnet-structured Li 6.75 La 3 Zr 1.75 Ta 0.25 O 12 (LLZTO) is one of the most promising electrolyte materials for solid-state Li batteries (SS-LiB). The design and fabrication of a good cathode/electrolyte interface is an important criterion for the SS-LiB. In this work, we performed a systematic study on the impact of cathode crystal structure and chemical compositions on their chemical stabilities against the LLZTO at elevated temperatures, which are required for their adhesion during cell fabrication processes. X-ray Diffraction (XRD) and Rietveld refinement analyses revealed the chemical stabilities of various cathode materials in contact with the LLZTO. While layered LiCoO 2 cathode showed good stability in contact with LLZTO to 900 °C, LiNiO 2 or Ni-rich LiNi x Mn y Co 1–x–y O 2 (NMC) cathodes suffered from the formation of La 4 NiLiO 8 due to La-diffusion from LLZTO. Furthermore, Mn-rich LiMn 2 O 4 spinel and layered LiNi 1/3 Mn 1/3 Co 1/3 O 2 cathodes suffered from the formation of La 2 Zr 2 O 7 due to Li-diffusion and production of Li 2 MnO 3 . As a result, LiNi 0.6 Mn 0.2 Co 0.2 O 2 , having an ideal balance of Ni/Mn/Co composition, or Li 2 MnO 3 containing cathodes such as Li 1.2 Ni 0.15 Mn 0.55 Co 0.1 O 2 were found to have excellent phase stability as the cathodes for LLZTO-based SS-LiBs.
Multifunctional Composite Binder for Thick High-Voltage Cathodes in Lithium-Ion Batteries
Not provided.
Relationship of Chemical Composition and Moisture Sensitivity in LiNi x Mn y Co 1-x-y O 2 for Lithium-Ion Batteries
Chemical composition–moisture sensitivity relationship of LiNi x Mn y Co 1-x-y O 2 (NMC) cathode materials was investigated by exploring crystal structures, surface properties, and electrochemical performance behaviors of various commercial NMC powders: LiNi 1/3 Mn 1/3 Co 1/3 O 2 (NMC111), LiNi 0.5 Mn 0.3 Co 0.2 O 2 (NMC532), LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622), and LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811). The NMC powders were stored in different moisture conditions: moisture-free, humidified air, or immersed in water. Rietveld refinement analysis of X-ray diffraction (XRD) data and scanning electron microscopy (SEM) were used to characterize the crystal structure changes and the evolution of particle surfaces morphologies. The effect of moisture contamination on the electrochemical properties of NMC cathodes was studied by galvanostatic cycling and electrochemical impedance spectroscopy (EIS). The moisture contamination resulted in either structural disorder or unwanted surficial deposition products, which increased a charge-transfer impedance and consequent performance degradation of battery cells. The results showed that NMC’s moisture vulnerability increased with Ni content (x) despite protective coatings on commercial particles, which stressed the necessity of alternative surface passivation strategies of Ni-rich NMC for broad applications such as electric vehicles and electrified aircraft propulsion.
An Integrated Design Approach for Infill Patterning of Fused Deposition Modeling and its Application to an Airfoil
We present a new approach to incorporate an internal stress distribution into the design of infill via fused deposition modeling of additive manufacturing (AM). This design approach differs from topology optimization, since the topology optimization of AM focuses on changing the overall shape of the product, whereas the approach we propose in this research focuses on the porous infill and remains the overall shape of the product intact. The approach presented here is effective if the overall shape is an important functioning aspect of a product and the stress is applied to the entire body, not to given localized points. As an application, we demonstrate an airfoil with its infill densities optimized based on the pressure applied during operation. Specifically, the stress of an airfoil is analyzed with operational loading conditions. The local density of the infill pattern is determined based on the computational stress analysis. The infill geometry is mathematically generated using a circle packing algorithm. Test results show that the airfoil with the optimized infill outperforms the same shape with the traditional uniform infill pattern of an airfoil having the same weight.
Integrated Nano-Domains of Disordered and Ordered Spinel Phases in LiNi 0.5 Mn 1.5 O 4 for Li-Ion Batteries
Recent calculations and experimental data suggest that understanding the local ordering behavior of Ni/Mn will be critical to optimize the electrochemical properties of LiNi 0.5 Mn 1.5 O 4 (LNMO) high voltage spinel. In this study, we systematically controlled the evolution of Ni and Mn ordering in LNMO samples by annealing them at 700 °C in air for different dwelling times, followed by quenching to room temperature. The long- and short-range ordering behavior of Ni and Mn were analyzed by combining neutron powder diffraction, X-ray powder diffraction (XRD), transmission electron microscopy (TEM), and Fourier transform infrared spectroscopy (FT-IR) data. The results show that the fraction of ordered phase increases rapidly during initial annealing at 700 °C for 6 h, and accompanied by decreasing amounts of secondary phases. Annealing longer than 6 h led to the growth in size of ordered domains (i.e., increased segregation of ordered and disordered domains) along with a slow increase in the fraction of ordered phase. The dependence of open circuit voltages (OCVs) of the LNMO on the degree of ordering agrees well with recent calculations using the density functional theory. The increase in the degree of ordering increases the open circuit voltage (OCV) and the initial capacity but reduces cycle life and rate capability. The LNMO delivered optimal battery performances (capacity, cycle life, and rate capability) after annealing at 700 °C for 2 h. This partially ordered sample showed the respective advantages from both disordered and ordered spinels: better spinel-phase purity (thus, higher initial capacity) from the ordered LNMO and better cycle life and rate capability from the disordered LNMO.
Visualizing oxygen anion transport pathways in NdBaCo 2 O 5+δ by in situ neutron diffraction
We characterized the layered perovskite NdBaCo 2 O 5+δ (NBCO) using neutron powder diffraction under in situ conditions from 577–852 °C and in 10 -1 to 10 -4 atm oxygen. The best fit to the data was obtained in the tetragonal (P4/mmm) space group. No oxygen atom vacancy ordering was observed that warranted a lowering of the symmetry to orthorhombic (Pmmm). Two P4/mmm structural models were investigated: Model 1 (no split sites) and Model 2 (split Nd and O 2 sites). Furthermore, transport of oxygen through the material via the vacancy hopping mechanism will likely involve the nearest-neighbor oxygen atom sites in the Nd layer. Total oxygen stoichiometry values were in the range 5.51 ≤ δ ≤ 5.11. The tetragonal lattice parameters increased with temperature as expected. But, the a-axis expands while the c-axis contracts with decreasing pO 2 at a given temperature due to increasing vacancy concentration in the Nd layer.
Overcoming phase instability of RBaCo2O5+ (R = Y and Ho) by Sr substitution for application as cathodes in solid oxide fuel cells
Phase instabilities of the RBaCo2O5+ (R = Y and Ho) layered-perovskites and their decompositions into RCoO3 and BaCoO3-z at 800 oC in air were investigated. This will restrict their high temperature applications such as cathodes in solid oxide fuel cell (SOFC). However, appropriate amount of Sr substitution ( 60 % for R = Y and 70 % for R = Ho) for Ba successfully stabilized the R(Ba1-xSrx)Co2O5+ phase at elevated temperatures. This can be explained by decreasing oxygen vacancies at R-O layer, decreasing R-O bonding length, and consequent improvement of structural integrity. In addition, the Sr substitution (x = 0.6 - 1.0) for Ba provided added benefit with respect to the chemical stability against Ce0.8Gd0.2O1.9 (GDC) electrolyte, which is a critical requirement for the cathodes in SOFC. Among the various compositions investigated, the Y(Ba0.3Sr0.7)Co2O5+ + GDC composite cathode delivered the optimum electrochemical performances with a stable phase demonstrating the potential as a cathode in SOFC.
Effect of Ca Doping on the Electrical Conductivity of the High-Temperature Proton Conductor LaNbO4
The sintering properties, crystal structure and electrical conductivity of La1-xCaxNbO4- (x=0, 0.005, 0.01, 0.015, 0.02 and 0.025), prepared by a conventional solid-state method, have been investigated using powder X-ray diffraction (XRD), scanning electron microscopy (SEM) and electrochemical impedance spectroscopy (EIS). In 2.5% Ca doped samples, a small amount of impurities Ca2Nb2O7 were observed from the XRD patterns. Impedance spectra show that the grain boundary resistance increases with increasing Ca content, while the bulk resistance remains essentially constant below 550 C. Despite the higher degree of grain growth was observed for higher Ca-doping levels, the total conductivity of the La1-xCaxNbO4- series decreases with increasing Ca content from 0.5 to 2.0 mol%. The activation energy for the total conductivity decreases with increasing Ca content from 0.71 eV (x=0) to 0.54 eV (x=0.01) for the high temperature tetragonal phase, then it increases to 0.60 eV for x=0.02. For the monoclinic phase, La0.995Ca0.005NbO4- shows the lowest activation energy of 1.26 eV. These results imply that the solubility of CaO in LaNbO4 is in the range from 0.5 to 1.0 mol%. By increasing the sintering temperature from 1500 C to 1550 C, the proton conductivity of the Ca-doped LaNbO4 was improved with enlarged grain size due to a reduction in the resistive grain boundary contribution.
(Y0.5In0.5)Ba(Co,Zn)4O7 cathodes with superior high-temperature phase stability for solid oxide fuel cells
(Y0.5In0.5)BaCo4-xZnxO7 (1.0 x 2.0) oxides crystallizing in a trigonal P31c structure have been synthesized and explored as cathode materials for solid oxide fuel cells (SOFC). At a given Zn content, the (Y0.5In0.5)BaCo4-xZnxO7 sample with 50 % Y and 50 % In exhibits much improved phase stability at intermediate temperatures (600 - 800 oC) compared to the samples with 100 % Y or In. However, the substitution of Zn for Co in (Y0.5In0.5)Ba(Co4-xZnx)O7 (1.0 x 2.0) decreases the amount of oxygen loss on heating, total electrical conductivity, and cathode performance in SOFC while providing good long-term phase stability at high temperatures. Among the various chemical compositions investigated in the (Y0.5In0.5)Ba(Co4-xZnx)O7 system, the (Y0.5In0.5)BaCo3ZnO7 sample offers a combination of good electrochemical performance and low thermal expansion coefficient (TEC) while maintaining superior phase stability at 600 800 oC for 100 h. Fuel cell performances of the (Y0.5In0.5)Ba(Co3Zn)O7 + Ce0.8Gd0.2O1.9 (GDC) (50 : 50 wt. %) composite cathodes collected with anode-supported single cell reveal a maximum power density value of 521 mW cm-2 at 700 oC.
Effects of genistein on early-stage cutaneous wound healing
Highlights: {yields} We examine the effect of genistein on cutaneous wound healing. {yields} Genistein enhanced wound closure during the early stage of wound healing. {yields} These genistein effects on wound closure were induced by reduction of oxidative stress through increasing antioxidant capacity and modulation of pro-inflammatory cytokine expression. -- Abstract: Wound healing occurs in three sequential phases: hemostasis and inflammation, proliferation, and remodeling. Inflammation, the earliest phase, is considered a critical period for wound healing because immune cells remove damaged tissues, foreign debris, and remaining dead tissue. Wound healing would be delayed without inflammation, and this phase is affected by antioxidation capacity. Therefore, we hypothesized that genistein, which has an antioxidant effect, might modulate the wound healing process by altering the inflammatory response. After three days of acclimation, mice were divided into three groups: control, 0.025% genistein, and 0.1% genistein. After two weeks of an experimental diet, skin wounds were induced. Wounded skin areas were imaged, and the healing rate calculated. To measure lipid peroxidation, antioxidant enzyme expression and activity, and pro-inflammatory cytokine expression, skin and liver tissues were harvested at 12, 24, 48, and 72 h. Genistein did not affect body weight. The rate of wound closure in mice fed genistein was significantly faster than in the control group during the early stage of wound healing, especially in first three days. Cu, Zn-SOD and Mn-SOD expression in wound skin tissue in the 0.1% genistein group was lower than in the control group. However, CAT expression did not differ among groups. We also found that genistein modulated NF-{kappa}B and TNF-{alpha} expression during the early stage of wound healing. The genistein group had significantly lower hepatic lipid peroxidation and higher SOD, CAT, and GPx activities than the control group. These results suggest that genistein supplementation reduces oxidative stress by increasing antioxidant capacity and modulating proinflammatory cytokine expression during the early stage of wound healing.
High temperature phase stabilities and electrochemical properties of InBaCo4-xZnxO7 cathodes for intermediate temperature solid oxide fuel cells
InBaCo4-xZnxO7 oxides have been synthesized and characterized as cathode materials for intermediate temperature solid oxide fuel cells (IT-SOFC). The effect of Zn substitution for Co on the structure, phase stability, thermal expansion, and electrochemical properties of the InBaCo4-xZnxO7 has been investigated. The increase in the Zn content from x = 1 to 1.5 improves the high temperature phase stability at 600 oC and 700 oC for 100 h, and chemical stability against a Gd0.2Ce0.8O1.9 (GDC) electrolyte. Thermal expansion coefficient (TEC) values of the InBaCo4-xZnxO7 (x = 1, 1.5, 2) specimens were determined to be 8.6 10-6 9.6 10-6 /oC in the range of 80 900 oC, which provides good thermal expansion compatibility with the standard SOFC electrolyte materials. The InBaCo4-xZnxO7 + GDC (50:50 wt. %) composite cathodes exhibit improved cathode performances compared to those obtained from the simple InBaCo4-xZnxO7 cathodes due to the extended triple-phase boundary (TPB) and enhanced oxide-ion conductivity through the GDC portion in the composites.
Phase Stability and Electrical Conductivity of Ca-doped LaNb1-xTaxO4- high temperature proton conductors
The electrical conductivity, phase structure and stability of La0.99Ca0.01Nb1-xTaxO4- (x=0, 0.1, 0.2, 0.3, 0.4 and 0.5, =0.005) a potential candidate for proton conductor for Solid Oxide Fuel Cells (SOFCs) have been investigated using AC impedance technique and in-situ X-ray powder diffraction. Partially substituting Nb with Ta elevates the phase transition temperature (from monoclinic to a tetragonal structure at high temperature) from ~520 C for x=0 to near 800 C for x=0.4. AC conductivity of the La0.99Ca0.01Nb1-xTaxO4- both in dry and wet air decreased slightly with increase of Ta content above 750 C, while below 500 C, it decreased one order of magnitude. It was also found that the activation energy for the total conductivity increases with increasing Ta content from 0.50 eV (x=0) to 0.58 eV (x=0.3) for the tetragonal phase, however, it decreases with increasing Ta content from 1.18 eV (x=0) to 1.08 eV (x=0.4) for the monoclinic phase. By removing the detrimental high temperature phase transition out of intermediate temperature range, partial substitution of Nb with Ta brings this class of material closer to its application in intermediate-temperature SOFCs.
Person to Person Biological Heat Bypass During EVA Emergencies
During EVA and other extreme environments, mutual human support is sometimes the last way to survive when there is a failure of the life support equipment. The possibility to transfer a coolant to remove heat or a warming fluid to increase heat from one individual to another to support the thermal balance of the individual with system failure was assessed. The following scenarios were considered: 1. one participant has a cooling system that is not working well and already has a body heat deficit equal to 100-120 kcal and a finger temperature decline to 25 C; 2. one participant has the same status of overcooling and the other mild overheating. Preliminary findings showed promise in using such sharing tactics to extend the time duration of survival in extreme situations when there is a high metabolic rate in the donor.