Search NASA⌕ Search

Engineering topics

Kim, K.

Publications and source records attributed to Kim, K..

49 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Fluid dynamics and convective heat transfer in impinging jets through implementation of a high resolution liquid crystal technique

A combined convective heat transfer and fluid dynamics investigation in a turbulent round jet impinging on a flat surface is presented. The experimental study uses a high resolution liquid crystal technique for the determination of the convective heat transfer coefficients on the impingement plate. The heat transfer experiments are performed using a transient heat transfer method. The mean flow and the character of turbulent flow in the free jet is presented through five hole probe and hot wire measurements, respectively. The flow field character of the region near the impingement plate plays an important role in the amount of convective heat transfer. Detailed surveys obtained from five hole probe and hot wire measurements are provided. An extensive validation of the liquid crystal based heat transfer method against a conventional technique is also presented. After a complete documentation of the mean and turbulent flow field, the convective heat transfer coefficient distributions on the impingement plate are presented. The near wall of the impingement plate and the free jet region is treated separately. The current heat transfer distributions are compared to other studies available from the literature. The present paper contains complete sets of information on the three dimensional mean flow, turbulent velocity fluctuations, and convective heat transfer to the plate. The experiments also prove that the present nonintrusive heat transfer method is highly effective in obtaining high resolution heat transfer maps with a heat transfer coefficient uncertainty of 5.7 percent.

Kim, K.↗
NASA NTRS1992

A new hue capturing technique for the quantitative interpretation of liquid crystal images used in convective heat transfer studies

A new image processing based color capturing technique for the quantitative interpretation of liquid crystal images used in convective heat transfer studies is presented. This method is highly applicable to the surfaces exposed to convective heating in gas turbine engines. It is shown that, in the single-crystal mode, many of the colors appearing on the heat transfer surface correlate strongly with the local temperature. A very accurate quantitative approach using an experimentally determined linear hue vs temperature relation is found to be possible. The new hue-capturing process is discussed in terms of the strength of the light source illuminating the heat transfer surface, the effect of the orientation of the illuminating source with respect to the surface, crystal layer uniformity, and the repeatability of the process. The present method is more advantageous than the multiple filter method because of its ability to generate many isotherms simultaneously from a single-crystal image at a high resolution in a very time-efficient manner.

Camci, C.↗
NASA NTRS1991

VLSI architectures for geometrical mapping problems in high-definition image processing

This paper explores a VLSI architecture for geometrical mapping address computation. The geometric transformation is discussed in the context of plane projective geometry, which invokes a set of basic transformations to be implemented for the general image processing. The homogeneous and 2-dimensional cartesian coordinates are employed to represent the transformations, each of which is implemented via an augmented CORDIC as a processing element. A specific scheme for a processor, which utilizes full-pipelining at the macro-level and parallel constant-factor-redundant arithmetic and full-pipelining at the micro-level, is assessed to produce a single VLSI chip for HDTV applications using state-of-art MOS technology.

Kim, K.↗
NASA NTRS1991

Direct kinematics solution architectures for industrial robot manipulators: Bit-serial versus parallel

A Very Large Scale Integration (VLSI) architecture for robot direct kinematic computation suitable for industrial robot manipulators was investigated. The Denavit-Hartenberg transformations are reviewed to exploit a proper processing element, namely an augmented CORDIC. Specifically, two distinct implementations are elaborated on, such as the bit-serial and parallel. Performance of each scheme is analyzed with respect to the time to compute one location of the end-effector of a 6-links manipulator, and the number of transistors required.

Lee, J.↗
NASA NTRS1985

The structure of the vorticity field in turbulent channel flow. I - Analysis of instantaneous fields and statistical correlations

An investigation into the existence of hairpin vortices in turbulent channel flow is conducted using a database generated by the large eddy simulation technique. It is shown that away from the wall the distribution of the inclination angle of vorticity vector attains its maximum at about 45 deg to the wall. Two point correlations of velocity and vorticity fluctuations strongly support a flow model consisting of vortical structures inclined at 45 deg to the wall. The instantaneous vorticity vectors plotted in planes inclined at 45 deg show that the flow contains an appreciable number of hairpins. Vortex lines are used to display the three dimensional structure of hairpins, which are shown to be generated from deformation of transverse vortex filaments.

Moin, P.↗
NASA NTRS1984

Containerless Processing of Advanced Glasses

Report describes investigation of containerless processing of glass, conducted in preparation of gravity-free processing experiments on board Space Shuttle. 105 candidate glass materials screened. Large number of oxide proportions studied and ternary phase diagram of glass formation developed as result.

Happe, R.↗
NASA NTRS1982

Behavior of liquid hydrogen inside an ICF target

The configuration of liquid hydrogen inside spherical glass shell ICF target was studied both theoretically and experimentally. Because of the zero contact angle between the .D2 liquid and glass substrate and the limited wetting surface that is continuous, the liquid hydrogen completely covers the interior of the glass shell, resulting in the formation of a void at the center. For this reason, the present problem distinguishes itself from that for a sessile drop sitting on a flat surface. A theory was formulated to calculate the liquid hydrogen configuration by including the London-dispersion force between the liquid and the substrate molecules. The net result is an augmented Bashforth-Adams equation appropriate to a spherical substrate, which is considered to be the major contribution of the present work. Preliminary calculations indicate that this equation accurately models the liquid hydrogen behavior inside a spherical microshell.

Kim, K.↗
NASA NTRS1980

Shock Sensitivity of energetic materials

Viscoplastic deformation is examined as the principal source of hot energy. Some shock sensitivity data on a proposed model is explained. A hollow sphere model is used to approximate complex porous matrix of energetic materials. Two pieces of shock sensitivity data are qualitatively compared with results of the proposed model. The first is the p2 tau law. The second is the desensitization of energetic materials by a ramp wave applied stress. An approach to improve the model based on experimental observations is outlined.

Kim, K.↗
NASA NTRS1977

Modeling of fluidized bed silicon deposition process

The model is intended for use as a means of improving fluidized bed reactor design and for the formulation of the research program in support of the contracts of Silicon Material Task for the development of the fluidized bed silicon deposition process. A computer program derived from the simple modeling is also described. Results of some sample calculations using the computer program are shown.

Kim, K.↗
NASA NTRS1976

Exit of a blast wave from a conical nozzle

The Eulerian computer code DORF was used in the analysis of a two-dimensional, unsteady flow field resulting from semi-confined explosions for propulsive applications. Initially, the ambient gas inside the conical shaped nozzle is set into motion due to the expansion of the explosion product gas, forming a shock wave. When this shock front exits the nozzle, it takes almost a spherical form while a complex interaction between the nozzle and compression and rarefaction waves takes place behind the shock. The results show an excellent agreement with experimental data.

Kim, K.↗
NASA NTRS1976

Blast wave in a nozzle for propulsive applications

The reported investigation has been conducted in connection with studies concerning the development of a propulsion system based on the use of a detonating fluid propellant. Measurements have been made of the pressure and shock wave velocity in a conical nozzle at various ambient pressures and at an ambient temperature of 25 C. In the experiments a small amount of explosive was placed at the end wall of a conical aluminum nozzle and detonated by a microdetonator inside the nozzle. Differences regarding the characteristics of conventional chemical propulsion and detonation propulsion are illustrated with the aid of a graph. One- and two-dimensional numerical flow calculations were performed and compared with the experimental data.

Varsi, G.↗
NASA NTRS1974

Measurements and calculations of detonation propulsion performance in helium

Previously obtained results are extended to helium ambient gas to help in the assessment of performance in the atmospheres of the major planets. Measurements confirm benefits derived form detonating propellant over conventional chemical rocket propulsion. Benefits however, are reduced at high pressures in low molecular weight gas. Numerical calculations by means of a monodimensional hydrodynamic code follow the different trends obtained experimentally for high and low molecular weight gas and also offer new insights on the time behavior of the process.

Kim, K.↗