Completion of the proton power upgrade project at the Spallation Neutron Source
Explore the source record for details and available documents.
Champion, Mark↗
Engineering topics
Kim, Sang-Ho
Publications and source records attributed to Kim, Sang-Ho.
Progress towards the completion of the proton power upgrade project
The Proton Power Upgrade project at the Spallation Neutron Source at Oak Ridge National Laboratory will increase the proton beam power capability from 1.4 to 2.8 MW. Upon completion in early 2025, 2 MW of beam power will be available for neutron production at the existing first target station (FTS) with the remaining beam power available for the future second target station (STS). The project has installed seven superconducting radio-frequency (RF) cryomodules and supporting RF power systems to increase the beam energy by 30% to 1.3 GeV, and the beam current will be increased by 50%. The injection and extraction region of the accumulator ring are being upgraded, and a new 2 MW mercury target has been developed along with supporting equipment for high-flow gas injection to mitigate cavitation and fatigue stress. The first four cryomodules and supporting systems were commissioned in 2022-2023 and supported neutron production at 1.05 GeV, 1.7 MW with high reliability. The first-article 2 MW target was operated successfully for approximately 4400 MW-Hours over two run periods. The long outage began in August 2023 for installation of the remaining technical equipment and construction of the Ring-to-Target Beam Transport tunnel stub that will enable connection to the STS without interrupting operation of the FTS. The upgrade is proceeding on-schedule and on-budget, and resumption of neutron production for the user program is planned for July 2024.
43 PARTICLE ACCELERATORS↗
Progress towards the completion of the proton power upgrade project
The Proton Power Upgrade project at the Spallation Neutron Source at Oak Ridge National Laboratory will increase the proton beam power capability from 1.4 to 2.8 MW. Upon completion in early 2025, 2 MW of beam power will be available for neutron production at the existing first target station (FTS) with the remaining beam power available for the future second target station (STS). The project has installed seven superconducting radio-frequency (RF) cryomodules and supporting RF power systems to increase the beam energy by 30% to 1.3 GeV, and the beam current will be increased by 50%. The injection and extraction region of the accumulator ring are being upgraded, and a new 2 MW mercury target has been developed along with supporting equipment for high-flow gas injection to mitigate cavitation and fatigue stress. The first four cryomodules and supporting systems were commissioned in 2022-2023 and supported neutron production at 1.05 GeV, 1.7 MW with high reliability. The first-article 2 MW target was operated successfully for approximately 4400 MW-Hours over two run periods. The long outage began in August 2023 for installation of the remaining technical equipment and construction of the Ring-to-Target Beam Transport tunnel stub that will enable connection to the STS without interrupting operation of the FTS. The upgrade is proceeding on-schedule and on-budget, and resumption of neutron production for the user program is planned for July 2024.
Champion, Mark↗
{phi} Meson Photoproduction on the Nucleon and 4He Targets
We study the reaction mechanism of phi-meson photoproduction on the nucleon and He-4 targets by using a dynamical model based on a Hamiltonian. In addition to the dominant contribution of the Pomeron exchange, various meson exchanges are considered in the t channel to describe the CLAS data in the low energy region root s =(1.97-2.84) GeV. The direct phi radiations are taken into account in the s- and u-channels. The backward structures at root s approximate to 2.1 and 2.3 GeV are well reproduced by the inclusion of the s-channel N(2000,5/2(+)) and N(2300,1/2(+))resonances, respectively. We also consider the final phi N interactions by the gluon exchange, the direct phi N interactions, and the box diagrams arising from the couplings with the pi N, rho N, K Lambda, and K Sigma channels. The effects of the final state interactions are found to be very weak. Then the resulting Hamiltonian is used to study the coherent gamma He-4 -> phi He-4 reaction within the distorted-weave impulse approximation. The calculated differential cross sections account for the LEPS data quite well.
Kim, Sang-Ho↗
Multipacting analysis of the SNS drift tube linac (DTL) RF vacuum window using Spark3d
An ongoing study at the Spallation Neutron Source (SNS) seeks to better understand and address potential multipacting issues associated with the Drift Tube Linac (DTL) RF vacuum windows. An analysis of several failed operational windows showed indications of excessive RF heating on the TiN-coated alumina ceramics. Coupled with vacuum bursts and arcing during conditioning and/or operational periods, these problems have been attributed to electron activity likely caused by multipacting. The status of the study, 3-D electromagnetic simulation results, mitigating techniques and a future experimental plan for studying multipacting in the SNS DTL vacuum windows are presented.
Toby, George↗
High Power Radiofrequency Operation of the Radiofrequency Quadrupoles in the Spallation Neutron Source
The Spallation Neutron Source (SNS) recently took delivery of a third Radiofrequency Quadrupole (RFQ03) that will ultimately be installed on the front-end (FE) of the SNS Linac. The first RFQ (RFQ01) operated in the SNS FE for more than a decade before being replaced with the second RFQ (RFQ02). RFQ01 was relocated to the Beam Test Facility (BTF) where it operated for five more years. The RFQ02 was initially installed in the BTF for high power testing and used with H- beam for BTF operation. It replaced RFQ01 in the SNS FE in 2017 and has been operating for beam production since then. There are some differences between the three RFQs. RFQ01 has a square cross-section with pi-mode stabilizing loops (PISLs) with the structure being fabricated using two layers of materials, GlidCop outside and OFHC inside. RFQ02 and RFQ03 has an octagonal cross-section with end-wall stabilizer rods and was fabricated using OFHC only. RFQ01 suffered some field flatness distortion incidents that resulted in degradation in beam transmission efficiency and required RF tuning. RFQ02 has performed well but had a melted RF seal in the high energy end wall, that was ultimately mitigated by a redesign of the end flange seals. The SNS decided to order RFQ03 that has a design that followed that of RFQ02 closely, but end-wall contacts were modified to prevent RF seal failure. This report presents the testing, installation, high power RF operation, and design improvements of the RFQ03.
Ren, Haitao↗
Progress on the Proton Power Upgrade Project at the Spallation Neutron Source
The Proton Power Upgrade Project at the Spallation Neutron Source at Oak Ridge National Laboratory will increase the proton beam power capability from 1.4 to 2.8 MW. Upon completion of the project, 2 MW of beam power will be available for neutron production at the existing first target station with the remaining beam power available for the future second target station. The project will install seven superconducting RF cryomodules and supporting RF power systems and ancillaries to increase the beam energy to 1.3 GeV . The injection and extraction region of the accumulator ring will be upgraded, and a new 2 MW mercury target has been developed along with supporting equipment for high-flow gas injection to mitigate cavitation and fatigue stress. Equipment is being received from vendors and partner laboratories, and installation is underway with three major installation outages planned in 2022-2024. The project is planned to be completed in 2025.
43 PARTICLE ACCELERATORS↗
Progress on the Proton Power Upgrade Project at the Spallation Neutron Source
The Proton Power Upgrade Project at the Spallation Neutron Source at Oak Ridge National Laboratory will increase the proton beam power capability from 1.4 to 2.8 MW. Upon completion of the project, 2 MW of beam power will be available for neutron production at the existing first target station with the remaining beam power available for the future second target station. The project will install seven superconducting RF cryomodules and supporting RF power systems and ancillaries to increase the beam energy to 1.3 GeV . The injection and extraction region of the accumulator ring will be upgraded, and a new 2 MW mercury target has been developed along with supporting equipment for high-flow gas injection to mitigate cavitation and fatigue stress. Equipment is being received from vendors and partner laboratories, and installation is underway with three major installation outages planned in 2022-2024. The project is planned to be completed in 2025.
Barbier, Charlotte↗
Dynamical model of φ meson photoproduction on the nucleon and 4 He
We investigate φ meson photoproduction on the nucleon and the 4 He targets within a dynamical model approach based on a Hamiltonian which describes the production mechanisms by the Pomeron-exchange, meson-exchanges, φ radiations, and nucleon resonance excitations mechanisms. The final φN interactions are included being described by the gluon-exchange, direct φN couplings, and the box-diagrams arising from the couplings with πN, ρN, KΛ, and KΣ channels. The parameters of the Hamiltonian are determined by the experimental data of γp → φp from the CLAS Collaboration. The resulting Hamiltonian is then used to predict the coherent φ-meson production on the 4 He targets by using the distorted-wave impulse approximation. For the proton target, the final φN rescattering effects, as required by the unitarity condition, are found to be very weak, which supports the earlier calculations in the literature. For the 4 He targets, the predicted differential cross sections are in good agreement with the data obtained by the LEPS Collaboration. Furthermore, the role of each mechanism in this reaction is discussed and predictions for a wide range of scattering angles are presented, which can be tested in future experiments.
73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
SNS Warm Linac Circulator Breakdown Considerations for the PPU Project
Multipacting in accelerating structures is a complex phenomenon about which there is much to be understood. While multipacting research efforts have primarily been focused on superconducting radio frequency (SRF) systems, normal conducting accelerating structures which have a higher thermal capacity, and a greater vacuum pressure tolerance could benefit from additional investigation. This research details multipacting simulation methods and the results of 3-D electromagnetic simulations of RF vacuum windows used on normal conducting linac (NCL) cavities. Benchmarking of the peak electric fields in these structures, benefits of material processing and possible techniques for reducing or eliminating multipacting activities are discussed.
Toby, George↗
Multipacting Analysis of Warm Linac RF Vacuum Windows
Multipacting in accelerating structures is a complex phenomenon with which there is much to be understood. While multipacting research efforts have primarily been focused on superconducting radio frequency (SRF) systems, normal conducting accelerating structures that have a higher thermal capacity and a greater vacuum pressure tolerance could benefit from additional investigation. This research details multipacting simulation methods and the results of 3-D electromagnetic simulations of RF vacuum windows used on normal conducting linac (NCL) cavities. Possible techniques for reducing and eliminating multipacting activities in these structures are discussed.
Toby, George↗
Progress on the Proton Power Upgrade at the Spallation Neutron Source
The Proton Power Upgrade Project at the Spallation Neutron Source (SNS) at Oak Ridge National Laboratory will double the proton power capability from 1.4 to 2.8 MW. This will be accomplished through an energy increase from 1.0 to 1.3 GeV and a beam current increase from 26 to 38 mA. The energy increase will be accomplished through the addition of 7 cryomodules to the linear accelerator (Linac). The beam current increase will be supported by upgrading several radio-frequency systems in the normal-conducting section of the Linac. Upgrades to the accumulator ring injection and extraction regions will accommodate the increase in beam energy. A new 2-MW-capable target and supporting systems will be developed and installed. Conventional facility upgrades include build-out of the existing klystron gallery and construction of a tunnel stub to facilitate future beam transport to the second target station. The project received approval to proceed with construction in October 2020. Procurements are in progress, and some installation activities have already occurred. Most of the installation will take place during three outages in 2022-2023. The project early finish is planned for 2025.
Barbier, Charlotte↗
Final Design Report Proton Power Upgrade Project
Explore the source record for details and available documents.
43 PARTICLE ACCELERATORS↗