Search NASASearch

Engineering topics

Kimes, D. S.

Publications and source records attributed to Kimes, D. S..

At least 19 records

Secondary Forest Age and Tropical Forest Biomass Estimation Using TM

The age of secondary forests in the Amazon will become more critical with respect to the estimation of biomass and carbon budgets as tropical forest conversion continues. Multitemporal Thematic Mapper data were used to develop land cover histories for a 33,000 Square kM area near Ariquemes, Rondonia over a 7 year period from 1989-1995. The age of the secondary forest, a surrogate for the amount of biomass (or carbon) stored above-ground, was found to be unimportant in terms of biomass budget error rates in a forested TM scene which had undergone a 20% conversion to nonforest/agricultural cover types. In such a situation, the 80% of the scene still covered by primary forest accounted for over 98% of the scene biomass. The difference between secondary forest biomass estimates developed with and without age information were inconsequential relative to the estimate of biomass for the entire scene. However, in futuristic scenarios where all of the primary forest has been converted to agriculture and secondary forest (55% and 42% respectively), the ability to age secondary forest becomes critical. Depending on biomass accumulation rate assumptions, scene biomass budget errors on the order of -10% to +30% are likely if the age of the secondary forests are not taken into account. Single-date TM imagery cannot be used to accurately age secondary forests into single-year classes. A neural network utilizing TM band 2 and three TM spectral-texture measures (bands 3 and 5) predicted secondary forest age over a range of 0-7 years with an RMSE of 1.59 years and an R(Squared) (sub actual vs predicted) = 0.37. A proposal is made, based on a literature review, to use satellite imagery to identify general secondary forest age groups which, within group, exhibit relatively constant biomass accumulation rates.

Nelson, R. F.

NOAA AVHRR Land Surface Albedo Algorithm Development

The primary objective of this research is to develop a surface albedo model for the National Oceanic and Atmospheric Administration (NOAA) Advanced Very High Resolution Radiometer (AVHRR). The primary test site is the Konza prairie, Kansas (U.S.A.), used by the International Satellite Land Surface Climatology Project (ISLSCP) in the First ISLSCP Field Experiment (FIFE). In this research, high spectral resolution field spectrometer data was analyzed to simulate AVHRR wavebands and to derive surface albedos. Development of a surface albedo algorithm was completed by analysing a combination of satellite, field spectrometer, and ancillary data. Estimated albedos from the field spectrometer data were compared to reference albedos derived using pyranometer data. Variations from surface anisotropy of reflected solar radiation were found to be the most significant albedo-related error. Additional error or sensitivity came from estimation of a shortwave mid-IR reflectance (1.3-4.0 micro-m) using the AVHRR red and near-IR bands. Errors caused by the use of AVHRR spectral reflectance to estimate both a total visible (0.4-0.7 micro-m) and near-IR (0.7-1.3 micro-m) reflectance were small. The solar spectral integration, using the derived ultraviolet, visible, near-IR and SW mid-IR reflectivities, was not sensitive to many clear-sky changes in atmospheric properties and illumination conditions.

Toll, D. L.

Application of AI techniques to infer vegetation characteristics from directional reflectance(s)

Traditionally, the remote sensing community has relied totally on spectral knowledge to extract vegetation characteristics. However, there are other knowledge bases (KB's) that can be used to significantly improve the accuracy and robustness of inference techniques. Using AI (artificial intelligence) techniques a KB system (VEG) was developed that integrates input spectral measurements with diverse KB's. These KB's consist of data sets of directional reflectance measurements, knowledge from literature, and knowledge from experts which are combined into an intelligent and efficient system for making vegetation inferences. VEG accepts spectral data of an unknown target as input, determines the best techniques for inferring the desired vegetation characteristic(s), applies the techniques to the target data, and provides a rigorous estimate of the accuracy of the inference. VEG was developed to: infer spectral hemispherical reflectance from any combination of nadir and/or off-nadir view angles; infer percent ground cover from any combination of nadir and/or off-nadir view angles; infer unknown view angle(s) from known view angle(s) (known as view angle extension); and discriminate between user defined vegetation classes using spectral and directional reflectance relationships developed from an automated learning algorithm. The errors for these techniques were generally very good ranging between 2 to 15% (proportional root mean square). The system is designed to aid scientists in developing, testing, and applying new inference techniques using directional reflectance data.

Kimes, D. S.

Spatial averaging errors in creating hemispherical reflectance (albedo) maps from directional reflectance data

Spatial averaging errors which may occur when creating hemispherical reflectance maps for different cover types from direct nadir technique to estimate the hemispherical reflectance are assessed by comparing the results with those obtained with a knowledge-based system called VEG (Kimes et al., 1991, 1992). It was found that hemispherical reflectance errors provided by using VEG are much less than those using the direct nadir techniques, depending on conditions. Suggestions are made concerning sampling and averaging strategies for creating hemispherical reflectance maps for photosynthetic, carbon cycle, and climate change studies.

Kimes, D. S.

Learning class descriptions from a data base of spectral reflectance of soil samples

Consideration is given to a program developed to learn class descriptions from positive and negative training examples of spectral reflectance data of bare soils. It is a combination of 'learning by example' and the generate-and-test paradigm and is designed to provide a robust learning environment that can handle error-prone data. The program was tested by having it learn class descriptions of various categories of organic carbon content, iron oxide content, and particle size distribution in soils. These class descriptions were then used to classify an array of targets. The program found the sequence of relationships between bands that contained the most important information to distinguish the classes. Physical explanations for the class descriptions obtained are presented.

Kimes, D. S.

Remote sensing of surface hemispherical reflectance (albedo) using pointable multispectral imaging spectroradiometers

Remote techniques for determining albedo are examined in terms of the range of view angles required in the use of string techniques with the Moderate Resolution Imaging Spectroradiometer (MODIS) and the High Resolution Imaging Spectroradiometer (HIRIS). Ground data are used to compute full and half strings out to 15, 30, 45, and 60 degrees for various sun angles and ground cover types. A knowledge-based system is employed to evaluate both the visible and near-IR bands, and the results indicate errors of up to 7 percent for the MODIS data, HIRIS data, and the full-string +/- 60 degrees. In the cases of large extrapolations greater ranges of error are noted indicating that 60-deg systems are most effective. The error is increased in the case of sensor systems that only view in the fore or aft direction, and the MODIS full string for +/- 45 deg is also considered a good system.

Kimes, D. S.

Extracting spectral albedo from NOAA-9 AVHRR multiple view data using an atmospheric correction procedure and an expert system

A 100 km by 200 km area of the Sahel was selected to demonstrate a new method of extracting hemispherical reflectance (albedo) from directional satellite data. Utilizing a stratification of the Gao region of Mali based on soil texture, satellite data for homogeneous areas were selected. These data were employed in a knowledge-based expert system called VEG, which is designed to handle a wide variety of types of input data. The calculated directional reflectance factors at ground level are very similar to ground measurements noted in the literature.

Kimes, D. S.

New developments of a knowledge based system (VEG) for inferring vegetation characteristics

An extraction technique for inferring physical and biological surface properties of vegetation using nadir and/or directional reflectance data as input has been developed. A knowledge-based system (VEG) accepts spectral data of an unknown target as input, determines the best strategy for inferring the desired vegetation characteristic, applies the strategy to the target data, and provides a rigorous estimate of the accuracy of the inference. Progress in developing the system is presented. VEG combines methods from remote sensing and artificial intelligence, and integrates input spectral measurements with diverse knowledge bases. VEG has been developed to (1) infer spectral hemispherical reflectance from any combination of nadir and/or off-nadir view angles; (2) test and develop new extraction techniques on an internal spectral database; (3) browse, plot, or analyze directional reflectance data in the system's spectral database; (4) discriminate between user-defined vegetation classes using spectral and directional reflectance relationships; and (5) infer unknown view angles from known view angles (known as view angle extension).

Kimes, D. S.

Inferring vegetation characteristics using a knowledge-based system

A knowledge-based system for inferring physical and biological surface properties of vegetation using nadir and/or directional reflectance data as input is developed. A portion of this system has been developed to discriminate between user-defined vegetation classes using spectral and directional reflectance relationships. This discrimination program was used to classify targets into user-defined ground cover and plant height classes. The program learns class descriptors from samples (both positive and negative) of spectral, directional reflectance data of natural surfaces (bare soils, natural vegetation, and agricultural vegetation). The system is designed to handle any combination of directional view angles. The explicit relationships used in the class descriptions include greater-than relationships between combinations of two view angles and maximum and minimum value relationships. The class descriptions are used to classify an unknown target using the same directional views. The program was tested by learning class descriptions of various categories of percent ground cover and vegetation height.

Kimes, D. S.

Extraction of spectral hemispherical reflectance (albedo) of surfaces from nadir and directional reflectance data

A radiative transfer model is used to investigate how the error of spectral hemispherical reflectance data obtained from nadir reflectance values varies with wavelength, solar zenith angle, leaf area index, and leaf orientation distribution. Several techniques employing multiple off-nadir view angles taken in azimuth planes are found to accurately infer spectral hemispherical reflectances, and to be well suited to sensor systems that scan in a known azimuth plane or view fore and aft in a known azimuth plane. The effects of errors in hemispherical reflectance on terrestrial energy budget and productivity calculations is also considered.

Kimes, D. S.

Hemispherical reflectance variations of vegetation canopies and implications for global and regional budget studies

The hemispherical reflectance (HR) variations of vegetation canopies are studied as a function of solar zenith angle, wavelength, and canopy characteristics (leaf area index, leaf orientation distribution, and leaf and soil optical properties). The radiative transfer model of Kimes (1984) is used to explain the radiative transfers that give rise to variations in the HR for various vegetation canopies as a function of sun angle. The results of this model are compared with those calculated from Sellers' (1985) analytical two-stream approximation. It is noted that the findings have significant implications for a wide range of global and regional energy budget studies.

Kimes, D. S.

Directional reflectance distributions of a hardwood and pine forest canopy

A hand-held radiometer with AVHRR bands 1 and 2 was used to measure the directional reflectance distributions for both a hardwood and a pine forest canopy from a helicopter platform; canopy characteristics were also measured on the ground. The reflectance distributions obtained are compared with the scattering behavior of agricultural and natural grassland canopies. In addition, the Kimes (1983) three-dimensional radiative transfer model is used to document the unique radiant transfers that occur in forest canopies in virtue of their geometric structure. Both the measurements and the model calculations show that dense forest canopy scattering is similar to that for crops and grasslands. Attention is given to the effects of sparse forest canopies.

Kimes, D. S.

Inferring hemispherical reflectance of the earth's surface for global energy budgets from remotely sensed nadir or directional radiance values

The relationship between directional reflectances spanning the entire reflecting hemisphere and hemispherical reflectance (albedo) and the effect of solar zenith angle and cover type on these relationships were investigated, using the results obtained from NOAA's 7/8 AVHRR ground-level reflectance measurements. Bands 1 (0.58-0.6B microns) and 2 (0.73-1. 1 microns) were used for reflectance measurements of 11 natural vegetation surfaces ranging from bare soils to dense vegetation canopies. The results show that errors in inferring hemispherical reflectance from nadir reflectance can be between 11 and 45 percent for all cover types and solar angles, depending on the viewing angles. A technique is described in which a choice of two specific view angles reduces this error to less than 6 percent for both bands and for all sun angles and cover types.

Kimes, D. S.

Modelisation of the optical scattering behaviour of the vegetation canopies

The three dimensional model of Kimes (1984) which can treat three dimensional variability in heterogeneous scenes, was used to test and expand physical scattering mechanisms involved in reflectance distribution dynamics by analyzing modeling and field data. The major physical phenomena causing the directional scattering behavior of vegetation canopies are presented. These include the strong anisotropic properties of the soil, and the anisotropic scattering properties of the vegetation as described by the phase function of the leaves and the geometric effects caused by vertical layers of leaves. This knowledge serves as a basis for defining optimum directional view angles for remote sensing strategies. An example on using knowledge of the scattering behavior of vegetation to develop techniques for extracting vegetation parameters (spectral albedo) from directional reflectance data is presented.

Kimes, D. S.

Modeling the radiant transfers of sparse vegetation canopies

The scattering dynamics of sparse vegetation canopies were studied within the framework of the three-dimensional radiative transfer model of Kimes (1984). The model was upgraded by including an algorithm for the anisotropic scattering of a soil boundary. Validation of the model was carried out using measured directional reflectance data for two canopies exhibiting typical scattering behavior with low and intermediate vegetation density. The canopies were: an orchard grass canopy; and a hard wheat canopy. A number of factors were found contributing to the final reflectance distribution of the canopies, including: (1) the strong anisotropic scattering properties of the soil; (2) the geometric effect of the vegetation probability gap function on the soil anisotropy and solar irradiance; and (3) the anisotropic scattering of vegetation which is controlled by the phase function and the layering of leaves. The application of the theoretical results to the development of earth-observing sensor systems is discussed.

Kimes, D. S.

Understanding the Radiant Scattering Behavior of Vegetated Scenes

Knowledge of the physics of the scattering behavior of vegetation will ultimately serve the remote sensing and earth science community in many ways. For example, it will provide: (1) insight and guidance in developing new extraction techniques of canopy characteristics, (2) a basis for better interpretation of off-nadir satellite and aircraft data, (3) a basis for defining specifications of future earth observing sensor systems, and (4) a basis for defining important aspects of physical and biological processes of the plant system. The overall objective of the three-year study is to improve our fundamental understanding of the dynamics of directional scattering properties of vegetation canopies through analysis of field data and model simulation data. The specific objectives are to: (1) collect directional reflectance data covering the entire exitance hemisphere for several common vegetation canopies with various geometric structure (both homogeneous and row crop structures), (2) develop a scene radiation model with a general mathematical framework which will treat 3-D variability in heterogeneous scenes and account for 3-D radiant interactions within the scene, (3) conduct validations of the model on collected data sets, and (4) test and expand proposed physical scattering mechanisms involved in reflectance distribution dynamics by analyzing both field and modeling data.

Kimes, D. S.

Directional reflectance factor distributions for cover types of Northern Africa

Directional reflectance factors that spanned the entire exitance hemisphere were collected on the ground throughout the morning period for common cover types in Tunisia, Africa. NOAA 7/8 AVHRR bands 1(0.58-0.68 micron) and 2 (0.7301.1 micron) were used in data collection. The cover types reported were a plowed field, annual grassland, steppe grassland, hard wheat, salt plain, and irrigated wheat. Several of these cover types had geometric structures that are extreme as compared to those reported in the literature. Comparisons were made between the dynamics of the observed reflectance distributions and those reported in the literature. It was found that the dynamics of the measured data could be explained by a combination of soil and vegetation scattering components. The data and analysis further validated physical principles that cause the reflectance distribution dynamics as proposed by field and simulation studies in the literature. Finally, the normalized difference transformation (Band 2 - Band 1)/(Band 1 + Band 2), which is useful in monitoring vegetation cover, generally decreased the variation in signal with changing view angle. However, several exceptions were noted.

Kimes, D. S.

Diurnal movements of cotton leaves expressed as thermodynamic work and entropy changes

It is pointed out that some important agricultural crops show heliotropic leaf movements. In these species, the proclivity of leaves to orient either perpendicularly or parallel or in some combination of these positions with respect to the sun is controlled by the leaf turgor and the availability of water. Such an orientational response is particularly noticeable for cotton. Schutt et al. (1985) have detailed leaf trajectories using three angles. The present investigation applies the three-angle representation to leaf trajectory mapping and to the calculation of the phase angle 'gamma' between the individual leaf normals and the solar direction. Using gamma, the thermodynamic work and entropy functions are evaluated and used to distinguish between the behavior of water-stressed and well watered cotton canopies.

Schutt, J. B.