Search NASA⌕ Search

Engineering topics

Kingsep, A S

Publications and source records attributed to Kingsep, A S.

X-pinch-based neutron source

Results are presented from experimental studies of the parameters of an X-pinch-based neutron source made of 70- to 80-{mu}m-diameter deuterated polyethylene fibers. At currents of up to 1.7 MA and a current rise time of {approx}150 ns, hot plasma spots were observed in the fiber crossing region. The formation of hot spots was accompanied by the generation of short soft X-ray pulses with a duration of 2-4 ns, as well as by neutron emission. The neutron energy was measured using the time-of-flight technique in four directions, at 0{sup o}, 90{sup o}, 180{sup o}, and 270{sup o} with respect to the load axis. The mean energy of the neutrons emitted along the axis towards the anode and cathode was found to be 2.0 {+-} 0.2 and 2.6 {+-} 0.1 MeV, respectively, and that of neutrons emitted in two opposite directions along the radius, 2.5 {+-} 0.1 and 2.4 {+-} 0.1 MeV. The maximum neutron yield at a current amplitude of 1.6 MA was of 10{sup 10} neutrons per shot.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Studies of plasma dynamics in megampere X-pinches

Results are presented from experimental studies of the dynamics and parameters of the plasma generated by megampere (up to 2.3 MA) currents flowing through X-pinches formed from crossed wires made of various materials. The experiments were performed with different numbers of wires and different wire diameters. The X-ray yield in neon-like molybdenum lines (in the 2.5- to 3-keV photon energy range) from a <20 {mu}m hot spot was larger than 10 J, and the soft X-ray power emitted from this spot reached 120 GW. The hot-spot lifetime estimated by comparing the measured and calculated emission intensities and line profiles of helium-like Fe and Cr ions was {approx}10 ps. Hard X-ray emission in the photon energy range {>=}800 keV was also detected.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Transportation properties of a high-current magnetically insulated transmission line and dynamics of the electrode plasma

Results are presented from experimental studies of a section of a magnetically insulated transmission line (MITL) with a current density of up to 500 MA/cm{sup 2} and linear current density of up to 7 MA/cm (the parameters close to those in a fast-Z-pinch-driven fusion reactor projected at Sandia Laboratories). The experiments were performed in the S-300 facility (3 MA, 0.15 {Omega}, 100 ns). At high linear current densities, the surface of the ohmically heated MITL electrode can explode and a plasma layer can form near the electrode surface. As a result, the MITL can lose its transmission properties due to the shunting of the vacuum gap by the plasma produced. In this series of experiments, the dynamics of the electrode plasma and the dependence of the transmission properties of the MITL on the material and cleanness of the electrode surface were studied. It is shown experimentally that, when the current with a linear density of up to 7 MA/cm begins to flow along a model MITL, the input and output currents differ by less than 10% over a time interval of up to 230 ns for nickel electrodes and up to 350 ns for a line with a gold central electrode. No effect of the oil film present on the electrode surface on the loss of the transmission properties of the line was observed. It is also shown that electron losses insignificantly contribute to the total current balance. The experimental results are compared with calculations of the electrode explosion and the subsequent expansion of the plasma layer. A conclusion is made that the life-time of the model MITL satisfies the requirements imposed on the transmission lines intended for use in the projected thermonuclear reactor.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗