Search NASA⌕ Search

Engineering topics

Kippelen, Bernard

Publications and source records attributed to Kippelen, Bernard.

16 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Inverted organic tandem solar cells with a charge recombination stack employing spatially confined p-type electrical doping

We report on the application of solution-based p-type electrical doping using 12-molybdophosphoric acid hydrate (PMA) to the fabrication of organic tandem solar cells. Such a doping approach leads to a spatially confined vertical doping profile down to a limited depth from the surface of polymer films, thus allowing the hole-collecting component of the charge recombination stack to be embedded in the photoactive layer of the bottom sub-cell. This simplifies the device architecture by removing the need for an extra dedicated hole-collecting layer. It is shown that this novel charge recombination stack comprising a PMA-doped bottom photoactive layer and a trilayer of Ag/AZO/PEIE is compatible with a solution-processed top photoactive layer. Here, the fabricated inverted organic tandem solar cells exhibit an open-circuit voltage that is close to the sum of the open-circuit voltages of the individual sub-cells, and a fill factor that is close to the better fill factor of the two sub-cells.

14 SOLAR ENERGY↗
DOE OSTI2022

An approach towards plastic scintillators from thermally activated delayed fluorescent dyes and cross-linkable bismuth compounds

Cross-linked polyvinyltoluene (PVT) based plastic scintillators loaded with dyes exhibiting thermally activated delayed fluorescence (TADF) and various amounts of (caproate)di-(methacrylate) bismuth (CMB) were developed. The co-polymerization of vinyl toluene monomer loaded with different weight ratios of CMB and 1 wt% of TADF dye yielded highly transparent cross-linked plastic scintillators with intense green photoluminescence. The thermal and mechanical properties of the scintillators were investigated using thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) and micro indentation techniques. Here, their performance for radiation detection was assessed by performing gamma spectroscopy using a Cs-137 source and benchmarked to commercial plastic scintillators. The loading of CMB was guided by Monte Carlo N-Particle (MCNP) simulations. The results of this study show that the cross-linking approach and the use of TADF dyes yield scintillators with good mechanical properties with a uniaxial yield strength up to ~66 MPa for compositions loaded with 40 wt% of CMB and high optical quality. However, the light yield in gamma spectroscopy experiments is found to be reduced with the addition of CMB, suggesting a trade-off between mechanical yield strength and light yield in gamma spectroscopy.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Extraction of intrinsic contact resistance in organic thin-film transistors with single channel length and high capacitance density

Accurate characterization of the intrinsic contact resistance is important for the optimization of organic thin-film transistors (OTFTs), especially in devices with high gate capacitance density. This study reports on a method for the extraction of the intrinsic, or gate-voltage independent, contact resistance from OTFTs. In contrast to the transfer length method (TLM), this method can be applied to devices with a single geometry. The method is an extension of the previously reported Y-function method and combines the model proposed by S. Luan et al. to analyze the effect of the gate voltage on the contact resistance. Here, this method is first applied to OTFTs with a bottom-gate top-contact geometry having varying gate capacitance density values. The intrinsic contact resistance is found to decrease with increased gate capacitance density with values ranging between 4 kΩcm and under 1 kΩcm when the gate capacitance is changed from 36.6 nF/cm 2 to 231.7 nF/cm 2 , respectively. These values are in good agreement with those obtained using TLM experiments. The new method is also shown to be applicable to OTFTs with top-gate bottom contact geometry.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Skin-like low-noise elastomeric organic photodiodes

Stretchable optoelectronics made of elastomeric semiconductors could enable the integration of intelligent systems with soft materials, such as those of the biological world. Organic semiconductors and photodiodes have been engineered to be elastomeric; however, for photodetector applications, it remains a challenge to identify an elastomeric bulk heterojunction (e-BHJ) photoactive layer that combines a low Young’s modulus and a high strain at break that yields organic photodiodes with low electronic noise values and high photodetector performance. Here, a blend of an elastomer, a donor-like polymer, and an acceptor-like molecule yields a skin-like e-BHJ with a Young’s modulus of a few megapascals, comparable to values of human tissues, and a high strain at break of 189%. Elastomeric organic photodiodes based on e-BHJ photoactive layers maintain low electronic noise current values in the tens of femtoamperes range and noise equivalent power values in the tens of picowatts range under at least 60% strain.

42 ENGINEERING↗
DOE OSTI2021

Increasing Volume in Conjugated Polymers to Facilitate Electrical Doping with Phosphomolybdic Acid

Molecular p-type electrical dopants have been proven useful to fine-tune the optoelectronic properties of bulk organic semiconductors and their interfaces. In this work, the volume in polymer films and its role in solution-based electrical p-type doping using phosphomolybdic acid (PMA) are studied. The polymer film volume was controlled using two approaches. One is based on heating both the PMA solution and the film prior to immersion. The second is based on coating the polymer film with a liquid blend that contains the PMA solution and a swelling solvent. 31 P NMR and FTIR experiments indicate that the Keggin structure appears to be preserved throughout the doping process. Results show that increasing the polymer volume facilitates the infiltration of the PMA Keggin structure, which results in an increased electrical p-type doping level.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Benzocyclobutene polymer as an additive for a benzocyclobutene-fullerene: application in stable p–i–n perovskite solar cells

A poly(methacrylate) with benzocyclobutene side chains, CL, has been synthesized by radical polymerization for use as a crosslinking additive for a previously reported benzocyclobutene-functionalized fullerene, PCBCB, which can be thermally insolubilized following solution processing. Films of PCBCB incorporating CL and n-doped with (IrCp*Cp) 2 exhibit in-plane electrical conductivities around ten times higher than those of n-doped films without CL, while the use of CL also reduces leaching of dopant ions from the film upon washing. The performance and stability of perovskite solar cells using insolubilized PCBCB:CL, insolubilized PCBCB, or PCBM as top electron-extraction layers are compared; cells with undoped PCBCB:CL extraction layers exhibit higher average and maximum power conversion efficiencies (16 and 18.5%, respectively) than their PCBM and PCBCB counterparts. Devices with undoped PCBCB:CL extraction layers also showed excellent thermal stability, retaining 92% of their stabilized power output after aging for 3000 h at 85 °C in the dark in a nitrogen atmosphere.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Organic photodetector with built-in amplification for the detection of visible light with low optical power

We report on an organic-based photodetector that integrates a dual-gate organic thin-film transistor (DG-OTFT) with an organic photodiode (OPD) to produce a device with a high effective responsivity at low optical power and video-rate compatible response. In this device, the OPD operates in photovoltaic mode, instead of the commonly used photoconductive mode, to modulate one of the gate voltages of the DG-OTFT. Effective responsivity values of 10 A W –1 are measured at optical power values lower than 10 nW at 635 nm. Here, modeling of the operation of this new photodetector suggests that effective responsivity values up to 10 5 A W –1 can be achieved at optical powers of 1 nW using current printing technology and state-of-the-art organic semiconductors.

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

Large-area low-noise flexible organic photodiodes for detecting faint visible light

Silicon photodiodes are the foundation of light-detection technology; yet their rigid structure and limited area scaling at low cost hamper their use in several emerging applications. A detailed methodology for the characterization of organic photodiodes based on polymeric bulk heterojunctions reveals the influence that charge-collecting electrodes have on the electronic noise at low frequency. The performance of optimized organic photodiodes is found to rival that of low-noise silicon photodiodes in all metrics within the visible spectral range, except response time, which is still video-rate compatible. Solution-processed organic photodiodes offer several design opportunities exemplified in a biometric monitoring application that uses ring-shaped, large-area, flexible, organic photodiodes with silicon-level performance.

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

Effects of particle inclusions on cracking in ultrathin barrier films

Here, the effects of particle inclusions with different mechanical properties on the development of cracks in ultra-thin barrier films have been studied. Two types of particles, alumina and poly(styrene-b-methyl methacrylate) with large differences in their elastic modulus were used, representing both hard and soft inclusions. Particles were seeded onto polyethylene naphthalate substrates and subsequently coated with atomic layer deposited Al 2 O 3 as a barrier film. Ca corrosion tests used to determine the performance of the barrier films revealed that soft polymer particle inclusions severely affect the development of cracking in barrier films as compared to stiff ceramic particles. Tensile tests also confirmed that the barrier films with polymer particle inclusions have the lowest value of critical onset strain. Parametric simulations, conducted by varying the elastic modulus of the particle inclusions over a wide range, resulted in a larger strain energy release rate near particle inclusions which promotes crack formation and negatively impacts the performance of barrier films with softer particle inclusions. Thus, the combination of high residual stresses in the barrier films with the presence of soft particle inclusions is found the most detrimental for the development of high-performance ultrathin barrier films.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Thermally Activated Delayed Fluorescence Sensitization for Highly Efficient Blue Fluorescent Emitters

Hyperfluorescence is emerging as a powerful strategy to develop optoelectronic devices with high-color purity and enhanced stability. It requires appropriate integration of a sensitizer displaying efficient thermally activated delayed fluorescence (TADF) and an emitter displaying strong, narrow-band fluorescence. Here, through a joint computational and experimental approach, we provide an unprecedented, end-to-end systems level description of the electronic and optical processes that take place in a hyperfluorescent emissive layer composed of a TADF sensitizer, bis(2,5-di(9H-carbazol-9-yl)phenyl)-1,3,4-oxadiazole (4CzDPO), and a fluorescent emitter, 2,5,8,11-tetra-tert-butylperylene (TBPe). We combine the photophysical properties measurement of the emissive layer with the computational determination of the electronic properties, film morphology, and excitation transfer phenomena. The Förster resonance energy transfer rates from 4CzDPO to TBPe are on the order of 1011 s–1, considerably higher than the radiative and non-radiative recombination rates for 4CzDPO. These features ensure nearly complete energy transfer to TBPe, leading to a five-fold increase in the photoluminescence quantum yields in the 4CzDPO:TBPe system in comparison to neat films of 4CzDPO. Furthermore, our approach highlights the factors that can provide efficient energy transfer from TADF molecules to fluorescent emitters, suppress energy transfer among TADF molecules, and avoid the need for a host material within the emissive layer.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Organic thin-film transistors with a bottom bilayer gate dielectric having a low operating voltage and high operational stability

This study reports on p-channel bottom-gate organic thin-film transistors (OTFT) that achieve low-voltage operation with a thin bilayer gate dielectric of CYTOP/HfO 2 that also leads to high operational stability. A bottom-gate geometry allows the thickness of the gate dielectric to be reduced to 17 nm, thereby increasing the gate dielectric capacitance density to a value of up to 258 nF/cm 2 . All OTFTs yielded threshold voltages (V TH ) lower than -1 V, thereby providing minimum operating voltage (gate to source voltage ~ V TH ) of -1 V with field-effect mobility values in the range from 0.3 to 0.8 cm 2 /Vs and subthreshold swing values below 100 mV/dec. Operational stability during DC bias stress was found similar to that measured in devices with a top-gate geometry, with about 1% of drain current change after 6 h. Here, using a double-stretched exponential function, the operational stability characteristics were modeled. It was found that by increasing the metal oxide layer thickness, the threshold voltage can shift toward positive values under DC stress tests. For CYTOP layer thicknesses above 15 nm, a thicker CYTOP layer was found to shift the threshold voltage in the opposite direction toward negative values. Furthermore, these p-channel bottom-gate organic transistor with a bilayer gate dielectric of CYTOP/HfO 2 combine high mobility, high operational stability, and lower voltage operation of -1 V compared to top-gate OTFTs.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Impact of interface materials on side permeation in indirect encapsulation of organic electronics

This work demonstrates the impact of the contact interface between barrier films and adhesives on the side permeation of moisture into packaged devices. When barrier films are brought into contact with the adhesive layer during indirect encapsulation, permeation along defects at this interface can occur due to the imperfect nature of contact, resulting in the formation of pores. The connected network of pores can act as capillaries and be an alternative pathway for water permeation as opposed to the bulk of the adhesive or edge seal materials used for barrier attachment to the package. The rate of water permeation through the capillaries is governed by surface energies of the materials at the interfaces. Experimental results demonstrate that the rate of water permeation is significantly lowered by using materials with higher contact angles at the interface.

36 MATERIALS SCIENCE↗
NASA NTRS2002

Thermally stable molecules with large dipole moments and polarizabilities and applications thereof

Disclosed are fused ring bridge, ring-locked dyes that form thermally stable photorefractive compositions. The fused ring bridge structures are .pi.-conjugated bonds in benzene-, naphthalene- or anthracene-derived fused ring systems that connect donor and acceptor groups. The donor and acceptor groups contribute to a high molecular dipole moment and linear polarizability anisotropy. The polarization characteristics of the dye molecules are stabilized since the bonds in the fused ring bridge are not susceptible to rotation, reducing the opportunity for photoisomerization. The dyes are compatible with polymeric compositions, including thermoplastics. The dyes are electrically neutral but have charge transport, electronic and orientational properties such that upon illumination of a composition containing the dye, the dye facilitates refractive index modulation and a photorefractive effect that can be utilized advantageously in numerous applications such as in optical quality devices and biological imaging.

Marder, Seth R.↗
NASA NTRS2000

Process of changing the refractive index of a composite containing a polymer and a compound having large dipole moment and polarizability and applications thereof

Fused ring bridge, ring locked dyes that form thermally stable photorfractive compositions. The fused ring bridge structures are .pi.-conjugated bonds in benzene-, naphthalene- or anthracene-derived fused ring systems that connect donor and acceptor groups. The donor and acceptor groups contribute to a high molecular dipole moment and linear polarizability anisotropy. The polarization characteristics of the dye molecules are stabilized since the bonds in the fused ring bridge are not susceptible to rotation, reducing the opportunity for photoisomerization. The dyes are compatible with polymeric compositions, including thermoplastics. The dyes are electrically neutral but have charge transport, electronic and orientational properties such that upon illumination of a composition containing the dye, the dye facilitates refractive index modulation and a photorefractive effect that can be utilized advantageously in numerous applications such as in optical quality devices and biological imaging.

Marder, Seth R.↗