Search NASA⌕ Search

Engineering topics

Kiris, Cetin C.

Publications and source records attributed to Kiris, Cetin C..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2020

Computational Simulations of a Mach 0.745 Transonic Truss-Braced Wing Design

A joint effort between the NASA Ames and Langley Research Centers was undertaken to analyze the Mach 0.745 variant of the Boeing Transonic Truss-Braced Wing (TTBW) Design. Two different flow solvers, LAVA and USM3D, were used to predict the TTBW flight performance. Sensitivity studies related to mesh resolution and numerical schemes were conducted to define best practices for this type of geometry and flow regime. Validation efforts compared the numerical simulation results of various modeling methods against experimental data taken from the NASA Ames 11-foot Unitary Wind Tunnel experimental data. The fidelity of the computational representation of the wind tunnel experiment, such as utilizing a porous wall boundary condition to model the ventilated test section, was varied to examine how different tunnel effects influence CFD predictions. LAVA and USM3D results both show an approximate 0.5o angle of attack shift from experimental lift curve data. This drove an investigation that revealed that the trailing edge of the experimental model was rounded in comparison to the CAD model, due to manufacturing tolerances, which had not been accounted for in the initial simulations of the experiment. Simulating the TTBW with an approximation of this rounded trailing-edge reduces error by approximately 60%. An accurate representation of the tested TTBW geometry, ideally including any wing twists and deflections experienced during the test under various loading conditions, will be necessary for more thorough validation of the CFD.

Maldonado, Daniel↗
NASA NTRS2020

Computational Simulations of a Mach 0.745 Transonic Truss-Braced Wing Design

A joint effort between the NASA Ames and Langley Research Centers was undertaken to analyze the Mach 0.745 variant of the Boeing Transonic Truss-Braced Wing (TTBW) Design. Two different flow solvers, LAVA and USM3D, were used to predict the TTBW flight performance. Sensitivity studies related to mesh resolution and numerical schemes were conducted to define best practices for this type of geometry and flow regime. Validation efforts compared the numerical simulation results of various modeling methods against experimental data taken from the NASA Ames 11-foot Unitary Wind Tunnel experimental data. The fidelity of the computational representation of the wind tunnel experiment, such as utilizing a porous wall boundary condition to model the ventilated test section, was varied to examine how different tunnel effects influence CFD predictions. LAVA and USM3D results both show an approximate 0.5 angle of attack shift from experimental lift curve data. This drove an investigation that revealed that the trailing edge of the experimental model was rounded in comparison to the CAD model, due to manufacturing tolerances, which had not been accounted for in the initial simulations of the experiment. Simulating the TTBW with an approximation of this rounded trailing-edge reduces error by approximately 60%. An accurate representation of the tested TTBW geometry, ideally including any wing twists and deflections experienced during the test under various loading conditions, will be necessary for proper validation of the CFD.

Maldonado, Daniel↗
NASA NTRS2019

Efficient Near-Field to Mid-Field Sonic Boom Propagation Using a High-Order Space Marching Method

An efficient strategy for propagating sonic boom signatures from a near-field Computational Fluid Dynamics (CFD) solution to the mid-field is presented. The method is based on a high-order accurate finite-difference discretization of the 3D Euler equations on a specially designed curvilinear grid and a single sweep space marching solution algorithm. The new approach leads to more than a factor of two reduction in overall computational resources compared to the current method used to propagate near-field sonic booms to the ground. Accuracy and efficiency of the near-field to mid-field process is demonstrated using a selection of test cases from the AIAA Sonic Boom Prediction Workshops. Azimuthal dependence of nonlinear wave propagation from the near-field to mid-field is analyzed along with its effects on the ground level noise.

Housman, Jeffrey A.↗
NASA NTRS2019

Fully-Coupled Fluid-Structure Interaction Simulations of a Supersonic Parachute

A validated computational fluid-structure interaction method for simulating the complex interaction between the large deformation of very thin, highly deformable structures and compressible flows is extended to consider large-scale problems in supersonic flows using parallel computing. The coupled fluid-structure interaction system is solved in a partitioned, or weakly-coupled, manner. The foundations of the applied fluid-structure interaction method are a higher-order, block-structured Cartesian, sharp immersed boundary method for the compressible Navier-Stokes equations and a computational structural dynamics solver employing a geometrically nonlinear 3-node shell element based on the mixed interpolation of tensorial components formulation. The method is applied to large deformation fluid-structure interaction validation cases before being applied to the inflation of a supersonic parachute in the upper Martian atmosphere where the goal is to demonstrate the capabilities of the solver when considering large-scale problems in supersonic flows.

Boustani, Jonathan↗
NASA NTRS2019

Computation Simulations of Electric Propulsion Aircraft: The X-57 Maxwell

Outline - Introduction: X-57 CFD task overview; Motivation. Part I, Computational simulations without propulsion: Establishing CFD (Computational Fluid Dynamics) Best Practices - Grid generation - Mesh refinement study - Numerical methods - Wind tunnel validation study; Power-Off Aerodynamic Database Results. Part II, Computational simulations with propulsion: Cruise Power-On Database; High-Lift Power-On Database. Summary.

Duensing, Jared C.↗
NASA NTRS2019

Hybrid RANS/LES Simulation of Jet Surface Interaction Noise

NASA’s Commercial Supersonic Technology (CST) project has formulated a technical challenge to design a quiet propulsion system for a low boom supersonic aircraft that meets Federal Aviation Authority’s airport noise regulations with sufficient margin. Several proposed configurations take advantage of shielding from the wing or other air-frame components. Development of carefully validated computational tools are necessary for critically evaluating installation concepts that are currently being proposed to meet the technical challenge. Semi-empirical models that predict the noise reduction potential of arbitrary shielding surfaces are yet to mature. Another key challenge is the systematic assessment of additional noise from the interaction between high speed jet turbulence and a surface in it’s vicinity. As a first step towards predicting noise reduction due to radical installation concepts from first principles, we simulate the noise generated by a high speed turbulent round jet near a simple planar surface. Detailed comparisons are made with a dedicated experiment conducted at NASA’s Glenn Research Center. Sensitivity of far-field noise predictions to grid resolution is systematically documented. A permeable Ffowcs Williams Hawkings (FWH) surface enclosing both the jet and the shielding surface is used to predict far-field noise from the simulated flowfield. Details of the structured overset grids, numerical discretization, and turbulence model are provided. Near-field comparisons to PIV data and far-field comparisons to microphone array measurements are discussed. Excellent agreement for an initial validation study on an isolated free round jet was obtained and the findings were utilized in the jet surface interaction study. The split between shielded and reflected side of the microphone array was captured with good agreement, as well as the peak in the noise spectra due to scattering of turbulent energy into sound by the trailing edge of the surface.

Stich, Gerrit-Daniel↗
NASA NTRS2018

Application of Lattice Boltzmann and Navier-Stokes Methods to NASA's Wall Mounted Hump

Lattice Boltzmann (LB) based Large Eddy Simulation (LES), Reynolds-averaged Navier-Stokes (RANS) as well as hybrid RANS/LES methods within the Launch Ascent and Vehicle Aerodynamics (LAVA) solver framework are applied to NASA's wall-mounted hump. Computational results are compared with experiments performed by Greenblatt et al. A detailed comparison between the accuracy and resolution requirements of the two approaches for turbulence resolving simulations, as well as the suitability of different grid paradigms (body-fitted curvilinear and block structured Cartesian) are presented. This test case is part of NASA's Revolutionary Computational Aerosciences (RCA) sub-project which addresses the technical challenge of predicting flow separation and reattachment accurately. Improvements in predictive accuracy by as much as 90% are demonstrated using LB as well as hybrid RANS/LES approaches compared to state-of-the-art steady state RANS simulations.

Lattice Boltzmann↗
NASA NTRS2018

LAVA Simulations for the 3rd AIAA CFD High Lift Prediction Workshop with Body Fitted Grids

In response to the 3rd AIAA CFD High Lift Prediction Workshop, the workshop cases were analyzed using Reynolds-averaged Navier-Stokes flow solvers within the Launch Ascent and Vehicle Aerodynamics (LAVA) solver framework. For the workshop cases the advantages and limitations of both overset-structured an unstructured polyhedral meshes were assessed. The workshop included 3 cases: a 2D airfoil validation case, a mesh convergence study using the High Lift Common Research Model, and a nacelle/pylon integration study using the JAXA (Japan Aerospace Exploration Agency) Standard Model. The 2D airfoil case from the workshop is used to verify the implementation of the Spalart-Allmaras turbulence model along with some of its variants within the solver. The High Lift Common Research Model case is used to assess solver performance and accuracy at varying mesh resolutions, as well as identify the minimum mesh fidelity required for LAVA on this class of problem. The JAXA Standard Model case is used to assess the solver's sensitivity to the turbulence model and to compare the structured and unstructured mesh paradigms. These workshop cases have helped establish best practices for high lift flow configurations for the LAVA solver.

LAVA↗
NASA NTRS2018

Wall-Modeled Lattice Boltzmann and Navier-Stokes Approaches for Separated Flows

Lattice Boltzmann (LB) and hybrid Reynolds-averaged Navier-Stokes/large eddy simulation (RANS/LES) methods within the Launch Ascent and Vehicle Aerodynamics (LAVA) solver framework are applied to NASA's Revolutionary Computational Aerosciences (RCA) standard test cases for separated flows. A detailed comparison between the performance and accuracy of the two emerging numerical methodologies for turbulence resolving simulations, i.e. the LB and hybrid RANS/LES methods will be presented. This contribution addresses the RCA technical challenge to identify and down-select critical turbulence, transition, and numerical method technologies for 40% reduction in predictive error for standard turbulence separated flow test cases. Results for the 2D NASA wall-mounted hump and the axisymmetric transonic bump including time-averaged pressure coefficient, skin friction, and velocity pro les, as well as resolved and modeled Reynolds stresses for both numerical approaches will be presented and differences between LB and hybrid RANS/LES will be discussed.

Lattice Boltzmann↗
NASA NTRS2017

Lattice Boltzmann and Navier-Stokes Cartesian CFD Approaches for Airframe Noise Predictions

Lattice Boltzmann (LB) and compressible Navier-Stokes (NS) equations based computational fluid dynamics (CFD) approaches are compared for simulating airframe noise. Both LB and NS CFD approaches are implemented within the Launch Ascent and Vehicle Aerodynamics (LAVA) framework. Both schemes utilize the same underlying Cartesian structured mesh paradigm with provision for local adaptive grid refinement and sub-cycling in time. We choose a prototypical massively separated, wake-dominated flow ideally suited for Cartesian-grid based approaches in this study - The partially-dressed, cavity-closed nose landing gear (PDCC-NLG) noise problem from AIAA's Benchmark problems for Airframe Noise Computations (BANC) series of workshops. The relative accuracy and computational efficiency of the two approaches are systematically compared. Detailed comments are made on the potential held by LB to significantly reduce time-to-solution for a desired level of accuracy within the context of modeling airframes noise from first principles.

Airframe Noise Prediction↗
NASA NTRS2016

Solving Fluid Structure Interaction Problems with an Immersed Boundary Method

An immersed boundary method for the compressible Navier-Stokes equations can be used for moving boundary problems as well as fully coupled fluid-structure interaction is presented. The underlying Cartesian immersed boundary method of the Launch Ascent and Vehicle Aerodynamics (LAVA) framework, based on the locally stabilized immersed boundary method previously presented by the authors, is extended to account for unsteady boundary motion and coupled to linear and geometrically nonlinear structural finite element solvers. The approach is validated for moving boundary problems with prescribed body motion and fully coupled fluid structure interaction problems. Keywords: Immersed Boundary Method, Higher-Order Finite Difference Method, Fluid Structure Interaction.

Structure Interactions↗
NASA NTRS2016

Towards a Viscous Wall Model for Immersed Boundary Methods

Immersed boundary methods are frequently employed for simulating flows at low Reynolds numbers or for applications where viscous boundary layer effects can be neglected. The primary shortcoming of Cartesian mesh immersed boundary methods is the inability of efficiently resolving thin turbulent boundary layers in high-Reynolds number flow application. The inefficiency of resolving the thin boundary is associated with the use of constant aspect ratio Cartesian grid cells. Conventional CFD approaches can efficiently resolve the large wall normal gradients by utilizing large aspect ratio cells near the wall. This paper presents different approaches for immersed boundary methods to account for the viscous boundary layer interaction with the flow-field away from the walls. Different wall modeling approaches proposed in previous research studies are addressed and compared to a new integral boundary layer based approach. In contrast to common wall-modeling approaches that usually only utilize local flow information, the integral boundary layer based approach keeps the streamwise history of the boundary layer. This allows the method to remain effective at much larger y+ values than local wall modeling approaches. After a theoretical discussion of the different approaches, the method is applied to increasingly more challenging flow fields including fully attached, separated, and shock-induced separated (laminar and turbulent) flows.

Immersed↗