Search NASA⌕ Search

Engineering topics

Klann, Gary A.

Publications and source records attributed to Klann, Gary A..

7 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2006

Advances in Engine Test Capabilities at the NASA Glenn Research Center's Propulsion Systems Laboratory

The Propulsion Systems Laboratory at the National Aeronautics and Space Administration (NASA) Glenn Research Center is one of the premier U.S. facilities for research on advanced aeropropulsion systems. The facility can simulate a wide range of altitude and Mach number conditions while supplying the aeropropulsion system with all the support services necessary to operate at those conditions. Test data are recorded on a combination of steady-state and highspeed data-acquisition systems. Recently a number of upgrades were made to the facility to meet demanding new requirements for the latest aeropropulsion concepts and to improve operational efficiency. Improvements were made to data-acquisition systems, facility and engine-control systems, test-condition simulation systems, video capture and display capabilities, and personnel training procedures. This paper discusses the facility s capabilities, recent upgrades, and planned future improvements.

Pachlhofer, Peter M.↗
NASA NTRS2003

Flexwall Hydraulic Hose Replacement in the NASA Glenn 10- by 10-Foot Supersonic Propulsion Wind Tunnel

The space-time conservation-element and solution-element method is employed to numerically study the near-field screech-tone noise of a typical underexpanded circular jet issuing from a sonic nozzle. Both axisymmetric and fully three-dimensional computations are carried out. The self-sustained feedback loop is properly simulated. The computed shock-cell structure, acoustic wave length, screech-tone frequency, and sound-pressure levels are in good agreement with existing experimental results.

Smith, Larry E.↗
NASA NTRS1992

Contingency power for a small turboshaft engine by using water injection into turbine cooling air

Because of one-engine-inoperative (OEI) requirements, together with hot-gas reingestion and hot-day, high-altitude take-off situations, power augmentation for multiengine rotorcraft has always been of critical interest. However, power augmentation by using overtemperature at the turbine inlet will shorten turbine life unless a method of limiting thermal and mechanical stress is found. A possible solution involves allowing the turbine inlet temperature to rise to augment power while injecting water into the turbine cooling air to limit hot-section metal temperatures. An experimental water injection device was installed in an engine and successfully tested. Although concern for unprotected subcomponents in the engine hot section prevented demonstration of the technique's maximum potential, it was still possible to demonstrate increases in power while maintaining nearly constant turbine rotor blade temperature.

Biesiadny, Thomas J.↗
NASA NTRS1989

Injected Water Augments Cooling In Turboshaft Engine

Report describes experiments in which water injected into compressor-bleed cooling air of aircraft turboshaft engine. Injection of water previously suggested as way to provide additional cooling needed to sustain operation at power levels higher than usual. Involves turbine-inlet temperatures high enough to shorten lives of first-stage high-pressure turbine blades. Latent heat of vaporization of injected water serves as additional heat sink to maintain blades at design operating temperatures during high-power operation.

Biesiadny, Thomas J.↗
NASA NTRS1987

Contingency power for small turboshaft engines using water injection into turbine cooling air

Because of one engine inoperative requirements, together with hot-gas reingestion and hot day, high altitude takeoff situations, power augmentation for multiengine rotorcraft has always been of critical interest. However, power augmentation using overtemperature at the turbine inlet will shorten turbine life unless a method of limiting thermal and mechanical stresses is found. A possible solution involves allowing the turbine inlet temperature to rise to augment power while injecting water into the turbine cooling air to limit hot-section metal temperatures. An experimental water injection device was installed in an engine and successfully tested. Although concern for unprotected subcomponents in the engine hot section prevented demonstration of the technique's maximum potential, it was still possible to demonstrate increases in power while maintaining nearly constant turbine rotor blade temperature.

Biesiadny, Thomas J.↗
NASA NTRS1987

Contingency power for small turboshaft engines using water injection into turbine cooling air

Because of one engine inoperative requirements, together with hot-gas reingestion and hot day, high altitude takeoff situations, power augmentation for multiengine rotorcraft has always been of critical interest. However, power augmentation using overtemperature at the turbine inlet will shorten turbine life unless a method of limiting thermal and mechanical stresses is found. A possible solution involves allowing the turbine inlet temperature to rise to augment power while injecting water into the turbine cooling air to limit hot-section metal temperatures. An experimental water injection device was installed in an engine and successfully tested. Although concern for unprotected subcomponents in the engine hot section prevented demonstration of the technique's maximum potential, it was still possible to demonstrate increases in power while maintaining nearly constant turbine rotor blade temperature.

Biesiadny, Thomas J.↗