Search NASA⌕ Search

Engineering topics

Klimov, Victor I.

Publications and source records attributed to Klimov, Victor I..

At least 19 records

Two‐Color Amplified Spontaneous Emission from Auger‐Suppressed Quantum Dots in Liquids

Abstract Colloidal quantum‐dot (QD) lasing is normally achieved in close‐packed solid‐state films, as a high QD volume fraction is required for stimulated emission to outcompete fast Auger decay of optical‐gain‐active multiexciton states. Here a new type of liquid optical‐gain medium is demonstrated, in which compact compositionally‐graded QDs (ccg‐QDs) that feature strong suppression of Auger decay are liquefied using a small amount of solvent. Transient absorption measurements of ccg‐QD liquid suspensions reveal broad‐band optical gain spanning a wide spectral range from 560 (green) to 675 nm (red). The gain magnitude is sufficient to realize a two‐color amplified spontaneous emission (ASE) at 637 and 594 nm due to the band‐edge (1S) and the excited‐state (1P) transition, respectively. Importantly, the ASE regime is achieved using quasicontinuous excitation with nanosecond pulses. Furthermore, the ASE is highly stable under prolonged excitation, which stands in contrast to traditional dyes that exhibit strong degradation under identical excitation conditions. These observations point toward a considerable potential of high‐density ccg‐QD suspensions as liquid, dye‐like optical gain media that feature readily achievable spectral tunability and stable operation under intense photoexcitation.

Li, Xueyang↗

Colloidal Semiconductor Nanocrystal Lasers and Laser Diodes

Lasers and optical amplifiers based on solution-processable materials have been long-desired devices for their compatibility with virtually any substrate, scalability, and ease of integration with on-chip photonics and electronics. These devices have been pursued across a wide range of materials including polymers, small molecules, perovskites, and chemically prepared colloidal semiconductor nanocrystals, also commonly referred to as colloidal quantum dots. The latter materials are especially attractive for implementing optical-gain media as in addition to being compatible with inexpensive and easily scalable chemical techniques, they offer multiple advantages derived from a zero-dimensional character of their electronic states. These include a size-tunable emission wavelength, low optical gain thresholds, and weak sensitivity of lasing characteristics to variations in temperature. Here we review the status of colloidal nanocrystal lasing devices, most recent advances in this field, outstanding challenges, and the ongoing progress toward technological viable devices including colloidal quantum dot laser diodes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Optically Excited Lasing in a Cavity‐Based, High‐Current‐Density Quantum Dot Electroluminescent Device

Abstract Laser diodes based on solution‐processable materials can benefit numerous technologies including integrated electronics and photonics, telecommunications, and medical diagnostics. An attractive system for implementing these devices is colloidal semiconductor quantum dots (QDs). The progress towards a QD laser diode has been hampered by rapid nonradiative Auger decay of optical‐gain‐active multicarrier states, fast device degradation at high current densities required for laser action, and unfavorable competition between optical gain and optical losses in a multicomponent device stack. Here we resolve some of these challenges and demonstrate optically excited lasing from fully functional high‐current density electroluminescent (EL) devices with an integrated optical resonator. This advance has become possible due to excellent optical gain properties of continuously graded QDs and a refined device architecture, which allows for highly efficient light amplification in a thin, EL‐active QD layer.

36 MATERIALS SCIENCE↗

Colorless luminescent solar concentrators using colloidal semiconductor nanocrystals

Disclosed herein are embodiments of a composition comprising a polymer or sol-gel and one or more nanocrystals. The composition is useful as a luminescent solar concentrator. The nanocrystals are dispersed in the polymer or sol-gel matrix so as to reduce or substantially prevent nanocrystal-to-nanocrystal energy transfer and a subsequent reduction in the emission efficiency of the composition. In some embodiments, the polymer matrix comprises an acrylate polymer. Also disclosed herein is a method for making the composition. Devices comprising the composition are disclosed. In some cases the polymer is the waveguide, in others the polymer is applied as a coating on a waveguide. In some examples, the device is a window.

McDaniel, Hunter↗

Enhanced Emission from Bright Excitons in Asymmetrically Strained Colloidal CdSe/Cd x Zn 1– x Se Quantum Dots

Colloidal CdSe quantum dots (QDs) designed with a high degree of asymmetric internal strain have recently been shown to host a number of desirable optical properties including subthermal room-temperature line widths, suppressed spectral diffusion, and high photoluminescence (PL) quantum yields. It remains an open question, however, whether they are well-suited for applications requiring emission of identical single photons. Here we measure the low-temperature PL dynamics and the polarization-resolved fluorescence line narrowing spectra from ensembles of these strained QDs. Our spectroscopy reveals the radiative recombination rates of bright and dark excitons, the relaxation rate between the two, and the energy spectra of the quantized acoustic phonons in the QDs that can contribute to relaxation processes. In comparison to conventional colloidal CdSe/ZnS core/shell QDs, we find that in asymmetrically strained CdSe QDs over six times more light is emitted directly by the bright exciton. Furthermore, these results are therefore encouraging for the prospects of chemically synthesized colloidal QDs as emitters of single indistinguishable photons.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Semiconductor quantum dots: Technological progress and future challenges

In quantum-confined semiconductor nanostructures, electrons exhibit distinctive behavior compared with that in bulk solids. This enables the design of materials with tunable chemical, physical, electrical, and optical properties. Zero-dimensional semiconductor quantum dots (QDs) offer strong light absorption and bright narrowband emission across the visible and infrared wavelengths and have been engineered to exhibit optical gain and lasing. These properties are of interest for imaging, solar energy harvesting, displays, and communications. Here, we offer an overview of advances in the synthesis and understanding of QD nanomaterials, with a focus on colloidal QDs, and discuss their prospects in technologies such as displays and lighting, lasers, sensing, electronics, solar energy conversion, photocatalysis, and quantum information.

García de Arquer, F. Pelayo↗

Colloidal quantum dot lasers

We report semiconductor nanocrystals represent a promising class of solution-processable optical-gain media that can be manipulated via inexpensive, easily scalable colloidal techniques. Due to their extremely small sizes (typically <10 nm), their properties can be directly controlled via effects of quantum confinement; therefore, they are often termed colloidal quantum dots (CQDs). In addition to size-tunable emission wavelengths, CQDs offer other benefits for lasing applications, including low optical-gain thresholds and high temperature stability of lasing characteristics. Recent progress in understanding and practical control of processes impeding light amplification in CQDs has resulted in several breakthroughs, including the demonstration of optically pumped continuous-wave lasing, the realization of optical gain with direct current electrical injection and the development of dual-function electroluminescent devices that also operate as optically pumped lasers. The purpose of this Review is to assess the status of the field of CQD lasing and discuss the existing challenges and opportunities. A particular focus is on approaches for suppressing nonradiative Auger recombination, novel optical-gain concepts enabled by strong exciton-exciton interactions and controlled CQD charging, effects of nanocrystal form factors on light amplification and practical architectures for realizing electrically pumped CQD lasers. This overview suggests that the accumulated knowledge, along with the approaches developed for manipulating the optical-gain properties of colloidal nanostructures, perfectly position the CQD field for successfully addressing a long-standing challenge: the realization of CQD-based laser diodes. Colloidal quantum dots are promising materials for realizing versatile, wavelength-tunable, solution-processed lasers. This Review surveys recent advances in colloidal quantum dot lasing, provides an in-depth analysis of outstanding challenges and discusses a path forward to implementing technologically viable lasing devices.

36 MATERIALS SCIENCE↗

Charge-Transport Mechanisms in CuInSe x S 2– x Quantum-Dot Films

Colloidal quantum dots (QDs) have attracted considerable attention as promising materials for solution-processable electronic and optoelectronic devices. Copper indium selenium sulfide (CuInSe x S 2–x or CISeS) QDs are particularly attractive as an environmentally benign alternative to the much more extensively studied QDs containing toxic metals such as Cd and Pb. Carrier transport properties of CISeS-QD films, however, are still poorly understood. Here, we aim to elucidate the factors that control charge conductance in CISeS QD solids and, based on this knowledge, develop practical approaches for controlling the polarity of charge transport and carrier mobilities. To this end, we incorporate CISeS QDs into field-effect transistors (FETs) and perform detailed characterization of these devices as a function of the Se/(Se+S) ratio, surface treatment, thermal annealing, and the identity of source and drain electrodes. We observe that as-synthesized CuInSe x S 2–x QDs exhibit degenerate p-type transport, likely due to metal vacancies and CuIn’’ anti-site defects (Cu 1+ on an In 3+ site) that act as acceptor states. Moderate-temperature annealing of the films in the presence of indium source and drain electrodes leads to switching of the transport polarity to nondegenerate n-type, which can be attributed to the formation of In-related defects such as In Cu •• (an In 3+ cation on a Cu 1+ site) or In i ••• (interstitial In3+) acting as donors. We observe that the carrier mobilities increase dramatically (by 3 orders of magnitude) with increasing Se/(Se+S) ratio in both n- and p-type devices. To explain this observation, we propose a two-state conductance model, which invokes a high-mobility intrinsic band-edge state and a low-mobility defect-related intragap state. These states are thermally coupled, and their relative occupancies depend on both QD composition and temperature. Here, our observations suggest that the increase in the relative fraction of Se moves conduction- and valence band edges closer to low-mobility intragap levels. This results in increased relative occupancy of the intrinsic band-edge states and a corresponding growth of the measured mobility. Further improvement in charge-transport characteristics of the CISeS QD samples as well as their stability is obtained by infilling the QD films with amorphous Al 2 O 3 using atomic layer deposition.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Enhanced Multiple Exciton Generation in PbS|CdS Janus-like Heterostructured Nanocrystals

Generating multiple excitons by a single high-energy photon is a promising third generation solar energy conversion strategy. We demonstrate that multiple exciton generation (MEG) in PbS|CdS Janus-like hetero-nanostructures is enhanced over that of single-component and core/shell nanocrystal architectures, with an onset close to two times the PbS band gap. We attribute the enhanced MEG to the asymmetric nature of the hetero-nanostructure that results in an increase in the effective Coulomb interaction that drives MEG and a reduction of the competing hot exciton cooling rate. Slowed cooling occurs through effective trapping of hot-holes by a manifold of valence band interfacial states having both PbS and CdS character, as evidenced by photoluminescence studies and by ab initio calculations. Using transient photocurrent spectroscopy, we find that the MEG characteristics of the individual nanostructures are maintained in conductive arrays and demonstrate that these quasi-spherical PbS|CdS nanocrystals can be incorporated as the main absorber layer in functional solid-state solar cell architectures. Finally, based upon our analysis, we provide design rules for the next generation of engineered nanocrystals to further improve the MEG characteristics.

36 MATERIALS SCIENCE↗

Droop-Free Colloidal Quantum Dot Light-Emitting Diodes

Colloidal semiconductor quantum dots (QDs) are a highly promising materials platform for implementing solution-processable light-emitting diodes (LEDs). They combine high photostability of traditional inorganic semiconductors with chemical flexibility of molecular systems, which makes them well-suited for large-area applications such as television screens, solid-state lighting, and outdoor signage. Additional beneficial features include size-controlled emission wavelengths, narrow bandwidths, and nearly perfect emission efficiencies. State-of-the-art QD-LEDs exhibit high internal quantum efficiencies approaching unity. However, these peak values are observed only at low current densities (J) and correspondingly low brightnesses, whereas at higher J, the efficiency usually exhibits a quick roll-off. This efficiency droop limits achievable brightness levels and decreases device longevity due to excessive heat generation. We demonstrate QD-LEDs operating with high internal efficiencies (up to 70%) virtually droop-free up to unprecedented brightness of >100,000 cd m –2 (at ~500 mA cm –2 ). This exceptional performance is derived from specially engineered QDs that feature a compositionally graded interlayer and a final barrier layer. This QD design allows for improved balance between electron and hole injections combined with considerably suppressed Auger recombination, which helps mitigate efficiency losses due to charge imbalance at high currents. Finally, these results indicate a significant potential of newly developed QDs as enablers of future ultrabright, highly efficient devices for both indoor and outdoor applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Transient Spectroscopy of Glass-Embedded Perovskite Quantum Dots: Novel Structures in an Old Wrapping

Semiconductor doped glasses had been used by the research and engineering communities as color filters or saturable absorbers well before it was realized that their optical properties were defined by tiny specs of semiconductor matter known presently as quantum dots (QDs). Nowadays, the preferred type of QD samples are colloidal particles typically fabricated via organometallic chemical routines that allow for exquisite control of QD morphology, composition and surface properties. However, there is still a number of applications that would benefit from the availability of high-quality glass-based QD samples. These prospective applications include fiber optics, optically pumped lasers and amplifiers and luminescent solar concentrators (LSCs). In addition to being perfect optical materials, glass matrices could help enhance stability of QDs by isolating them from the environment and improving heat exchange with the outside medium. We conduct optical studies of a new type of all-inorganic CsPbBr 3 perovskite QDs fabricated directly in glasses by high-temperature precipitation. These samples are virtually scattering free and exhibit excellent waveguiding properties which makes them well suited for applications in, for example, fiber optics and LSCs. However, the presently existing problem is their fairly low room-temperature emission quantum yields of only ca. 1%–2%. Here we investigate the reasons underlying the limited emissivity of these samples by conducting transient photoluminescence (PL) and absorption measurements across a range of temperatures from 20 to 300K. We observe that the low-temperature PL quantum yield of these samples can be as high as ~25%. However, it quickly drops (in a nearly linear fashion) with increasing temperature. Interestingly, contrary to traditional thermal quenching models, experimental observations cannot be explained in terms of a thermally activated nonradiative rate but rather suggest the existence of two distinct QD sub-ensembles of “emissive” and completely “nonemissive” particles. The temperature-induced variation in the PL efficiency is likely due to a structural transformation of the QD surfaces or interior leading to formation of extremely fast trapping sites or nonemissive phases resulting in conversion of emissive QDs into nonemissive. Thus, future efforts on improving emissivity of glass-based perovskite QD samples might focus on approaches for extending the range of stability of the low-temperature highly emissive structure/phase of the QDs up to room temperature.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Superposition Principle in Auger Recombination of Charged and Neutral Multicarrier States in Semiconductor Quantum Dots

Application of colloidal semiconductor quantum dots (QDs) in optical and optoelectronic devices is often complicated by unintentional generation of extra charges, which opens fast nonradiative Auger recombination pathways whereby the recombination energy of an exciton is quickly transferred to the extra carrier(s) and ultimately dissipated as heat. Previous studies of Auger recombination have primarily focused on neutral and, more recently, negatively charged multicarrier states. Auger dynamics of positively charged species remains more poorly explored due to difficulties in creating, stabilizing, and detecting excess holes in the QDs. Here we apply photochemical doping to prepare both negatively and positively charged CdSe/CdS QDs with two distinct core/shell interfacial profiles (“sharp” versus “smooth”). Using neutral and charged QD samples we evaluate Auger lifetimes of biexcitons, negative and positive trions (an exciton with an extra electron or a hole, respectively), and multiply negatively charged excitons. Using these measurements, we demonstrate that Auger decay of both neutral and charged multicarrier states can be presented as a superposition of independent elementary three-particle Auger events. As one of the manifestations of the superposition principle, we observe that the biexciton Auger decay rate can be presented as a sum of the Auger rates for independent negative and positive trion pathways. Furthermore, by comparing the measurements on the QDs with the “sharp” versus “smooth” interfaces, we also find that while affecting the absolute values of Auger lifetimes, manipulation of the shape of the confinement potential does not lead to violation of the superposition principle, which still allows us to accurately predict the biexciton Auger lifetimes based on the measured negative and positive trion dynamics. Our findings indicate considerable robustness of the superposition principle as applied to Auger decay of charged and neutral multicarrier states, suggesting its generality to quantum-confined nanocrystals of arbitrary compositions and complexities.

36 MATERIALS SCIENCE↗

Two-Color Emitting Colloidal Nanocrystals as Single-Particle Ratiometric Probes of Intracellular pH

Intracellular pH is a key parameter in many biological mechanisms and cell metabolism and is used to detect and monitor cancer formation and brain or heart diseases. pH-sensing is typically performed by fluorescence microscopy using pH-responsive dyes. Accuracy is limited by the need for quantifying the absolute emission intensity in living biological samples. An alternative with a higher sensitivity and precision uses probes with a ratiometric response arising from the different pH-sensitivity of two emission channels of a single emitter. Current ratiometric probes are complex constructs suffering from instability and cross-readout due to their broad emission spectra. Here, we overcome such limitations using a single-particle ratiometric pH probe based on dot-in-bulk CdSe/CdS nanocrystals (NCs). These nanostructures feature two fully-separated narrow emissions with different pH sensitivity arising from radiative recombination of core- and shell-localized excitons. The core emission is nearly independent of the pH, whereas the shell luminescence increases in the 3–11 pH range, resulting in a cross-readout-free ratiometric response as strong as 600%. In vitro microscopy demonstrates that the ratiometric response in biologic media resembles the precalibralation curve obtained through far-field titration experiments. The NCs show good biocompatibility, enabling us to monitor in real-time the pH in living cells.

36 MATERIALS SCIENCE↗