Effects of particle size, distribution, and morphology on bulk shear behavior of milled loblolly pine
Not Available
Bhattacharjee, Tiasha↗
Engineering topics
Klinger, Jordan
Publications and source records attributed to Klinger, Jordan.
Mesoscopic flow simulation to understand the percolation through fine-ground electronic waste particle bed
Not Available
apparent permeability↗
A High-Performance Discrete-Element Framework for Simulating Flow and Jamming of Moisture Bearing Biomass Feedstocks
We developed and verified a high-performance open-source discrete element method (DEM) solver with simultaneously-supported feedstock-specific interaction models, including bonded-sphere, liquid bridge, cohesion, and non-linear contact models. Our solver uses parallel data structures on hybrid central and graphics processing unit (CPU/GPU) architectures, with favorable strong scaling performance observed for large problem sizes comprised of (100 M particles), and 4X single-node GPU speedup. The particles for corn stover feedstock were conceptualized and calibrated based on experimental measurements and results. Sensitivity analyses demonstrate that the mass flow rate from a wedge hopper is governed primarily by moisture content, friction coefficient, and cohesion energy density. The model is used to reproduce experimentally observed hopper jamming results, highlighting that the experimental no-flow trends can only be achieved by using non-spherical particles, liquid bridge and cohesion models, highlighting the importance of using concurrent feedstock specialized models for the effective representation of biomass material handling problems.
bioenergy↗
Discrete element modeling of irregular-shaped soft pine particle flow in an FT4 powder rheometer
Pine residues are a commonly used biomass feedstock that consists of different anatomical fractions, each with distinct particle characteristics. Here, in this work, an experiment-informed discrete element model is developed to investigate the flowability of pine residues in an FT4 rheometer. Multi-sphere particles with distinct particle attributes are created to model each anatomical fraction type. A systematic analysis of specimens with varying particle characteristics (e.g., anatomical fraction type, particle shape, and size) is conducted to elucidate the relationship between particle attributes and flowability. The results show that stems recorded the highest axial force and torque and, correspondingly, the highest flow energy, which is attributed to their high stiffness and interlocking effect. Increasing their percentage in the mixture increases the flow energy while increasing needles tends to decrease flow energy. Knowledge gained in this study on the flow of anatomical fractions is important for the efficient and robust processing of pine residues.
09 BIOMASS FUELS↗
The Effect of Air Separations on Fast Pyrolysis Products for Forest Residue Feedstocks
This study investigates the intricate relationship between biomass preprocessing and pyrolysis product yields, employing the air classification technique for the treatment of loblolly pine residues with varying moisture content. A comprehensive exploration of the physicochemical properties of air-classified loblolly pine informs a sophisticated pyrolysis simulation model. Given the complex and multifaceted nature of biomass pyrolysis, operating across diverse temporal and spatial scales, a pyrolysis kinetics-based CFD–DEM simulation method is employed to predict product yields. Results showed that the elevated moisture content amplifies particle adhesiveness, necessitating augmented air velocities for effective separation, thereby influencing the efficiency of the separation process. While carbon and hydrogen contents exhibit relative stability across diverse moisture contents and blower frequencies, the oxygen content undergoes noticeable changes. For example, the oxygen contents were measured as 29.2 and 38.6 wt% in the light fraction of 30% moisture content sample at blower frequencies of 10 and 20 Hz, respectively. An intriguing finding emerges from pyrolysis simulation, indicating that a lower blower frequency in air classification moderately enhances bio-oil yield and significantly improves its quality, particularly in terms of water content. For instance, the water content in the bio-oil was about 1.5% and 10% in the heavy and light fractions, respectively from 10% moisture sample under 15 Hz blower frequency. In summary, a detailed understanding and strategic manipulation of critical material attributes in biomass through efficient fractionation techniques are imperative for advancing fast pyrolysis as a sustainable avenue for renewable energy and chemical production.
09 BIOMASS FUELS↗
Experimental Investigation and Characterization of the Thermal Insulating Behavior of Municipal Solid Waste and its Constituents
Not Available
Saha, Nepu (ORCID:0000000340049864)↗
Predicting biomass comminution: Physical experiment, population balance model, and deep learning
An extended population balance model (PBM) and a deep learning-based enhanced deep neural operator (DNO+) model are introduced for predicting particle size distribution (PSD) of comminuted biomass through a large knife mill. Experimental tests using corn stalks with varied moisture contents, mill blade speeds, and discharge screen sizes are conducted to support model development. A novel mechanism in the extended PBM allows for including additional input parameters such as moisture content, which is not possible in the original PBM. The DNO+ model can include influencing factors of different data types such as moisture content and discharge screen size, which significantly extends the engineering applicability of the standard DNO model that only admits feed PSD and outcome PSD. Test results show that both models are remarkably accurate in the calibration or training parameter space and can be used as surrogate models to provide effective guidance for biomass preprocessing design.
09 BIOMASS FUELS↗
Particle size and shape effect of Crumbler® rotary shear-milled granular woody biomass on the performance of Acrison® screw feeder: A computational and experimental investigation
Physical experiments and discrete element model (DEM) simulations are conducted to evaluate particle characteristics and operation parameter effects on screw feeding performance for rotary shear-milled Douglas fir. Three performance metrics are used: mass flow rate, shaft driving torque, and specific energy consumption. The impact of particle size, particle size distribution (PSD), shaft rotational speed (rpm), and hopper dimensions on the performance are investigated. All employed performance metrics reveal the superior flowability of the 2-mm particles in contrast to the larger 6-mm counterpart. Remarkably, wider PSD results in poorer flowability than the two mono-sized particles, proving the flowability enhancement achieved by narrower PSD of the woody feedstock. More importantly, DEM simulations unveil PSD-induced degradation in flowability is attributed to mechanical interlocking and particle segregation effects. Furthermore, higher shaft rpm causes higher mass flow rate at the cost of higher specific energy consumption due to viscous dissipation and changes in flow pattern.
09 BIOMASS FUELS↗
Advanced Analytical Methodologies Enable Feedstock Screening and Correlation to Pyrolysis Yields and Catalytic Upgrading
Pyrolysis of lignocellulosic biomass can serve as a powerful pathway for the generation of renewable fuels and industrial products. However, procurement of some biomass may be costly, especially when there is competition for alternative uses. Forestry and agricultural byproducts may serve as valuable pyrolysis feedstocks due to their high availability and low cost. Although waste products may fill demand for affordable pyrolysis feedstocks, they are often high in ash and extractives which contribute to unfavorable changes in pyrolysis vapor composition, as well as end products. The work presented here investigates the correlations between various pine anatomical fractions to understand their effect on pyrolysis oil composition for forest residues. Analytical pyrolysis coupled to direct analysis by molecular beam mass spectrometry (MBMS) provides real-time monitoring of pyrolysis vapor composition, even for compounds that are not amenable to gas chromatography. Statistical analysis of MBMS data from the fast pyrolysis (FP) of clean pine, cambium, twigs and branches, needles, bark, and a forest residue samples revealed that bark and needles made the greatest differences in the vapor composition of forest residues during pyrolysis and were enriched in resin acids, furfural derivatives, and ions that have been previously observed from catalysis corresponding to ash content. These results were also compared to catalytic fast pyrolysis (CFP) using a platinum on titania catalyst, and correlations between FP and CFP products were observed for the anatomical fractions. The forest residues and corresponding anatomical fractions from a stand of 23-year-old pine will be converted by fast pyrolysis in a bench-scale 2-inch fluidized-bed reactor, and statistical correlations between the bench-scale products and analytical-scale pyrolysis vapors will be shown. This work highlights the power of advanced analytical methodologies in determining the contributions of vapor components to catalytic pyrolysis outcomes for mixed feedstocks and demonstrates the use of analytical methodologies to better screen feedstocks prior to pyrolysis.
analytical↗
Advanced biorefinery feedstock from non-recyclable municipal solid waste by mechanical preprocessing
Because of accelerated urbanization and the development of a global economy, a large quantity of municipal solid waste (MSW) has been collected and disposed of by the municipalities. Due to this drastic increase in the disposal of MSW, the need for its management is a must to preserve the environment. Currently, approximately 50% of the total MSW generated in the United States has been utilized through various recycling, combustion, and composting technologies, which means the remaining 50% is sent to landfill; this is often known as non-recyclable MSW (nMSW). As this nMSW is physically and chemically heterogenous and contains very high amounts of inorganic material, processing is required prior to using it as a biorefinery feedstock. Thus, this study focused on how mechanical preprocessing advanced the physical and chemical properties of nMSW. The physical and chemical properties were investigated in terms of particle size distribution, bulk density, ultimate and proximate analysis, and the higher heating value (HHV). The combustion properties were examined in terms of ignition temperature, peak heat release rate, and combustion efficiency. Results showed that the variability of physical and chemical properties of nMSW can be reduced by mechanical preprocessing. For example, the variability of the bulk density of the as-received nMSW was approximately 17.3% while it reduced to 5.8% when the sample size was reduced to 2 mm. Similarly, the variability of ash and HHV reduced from 49.2% to 11.0% and 13.4%–4.2%, respectively. Combustion thermograms showed that the size reduction positively improved the combustion properties. For example, 2 mm of spec sample started to ignite approximately 4 times earlier and took 6.5 folds less time to reach the peak heating rate compared to as-received nMSW. Overall, the mechanical preprocessing reduced the variability of physical and chemical properties in addition to the improvement of combustion behavior of the nMSW which is one step forward toward the biorefinery feedstock.
09 BIOMASS FUELS↗
Characterizing Biomass Feedstock Transport Properties Using State of the Art Imaging and Computational Techniques
The microstructure of lignocellulosic biomass determines heat and mass transfer during conversion processes. We present a novel method for characterizing the transport properties of biomass using advanced imaging and computational techniques. The microstructure of two woody feedstocks, red oak and Douglas fir, before and after pyrolysis, is revealed using X-ray computed tomography (XCT). Transport properties are calculated from the XCT images, and principal permeability tensors are calculated using an immersed boundary-based finite volume solver to model gas flow through the geometries. We observe that the permeabilities of native biomass are distinctly anisotropic, however, this anisotropy is greatly reduced after pyrolysis.
adaptive mesh refinement↗
Reverse scaling of a bonded-sphere DEM model: Formulation and application to lignocellulosic biomass microstructures
We explore scaling laws for adapting a bonded-sphere discrete element method (BS-DEM) model developed for woody structural mechanics at the millimeter scale to model the mechanics of realistic lignocellulosic biomass microstructures. Two scaling approaches, i.e., the reverse coarse graining (RCG) and equivalent bulk behavior (EBB), are proposed based on the classical mechanics principles and assessed in the single-particle compression and rectangular cuboid block tension tests. The EBB approach is recommended for BS-DEM models with general 3D geometries and is applied to simulate the microindentation test on a realistic microscale pinewood specimen. Simulations are performed to elucidate the impact of specimen thickness and loading position on the specimen’s force–deformation behavior. Furthermore, the range of Young’s modulus obtained from the calibrated BS-DEM simulations can match the experimental measurements. This is the first-of-its-kind study that has explored scale-bridging modeling approaches in biomass micromechanics and has proposed solutions based on BS-DEM models in the microscale.
59 BASIC BIOLOGICAL SCIENCES↗
Multiscale Shear Properties and Flow Performance of Milled Woody Biomass
One dominant challenge facing the development of biorefineries is achieving consistent system throughput with highly variant biomass feedstock quality and handling performance. Current handling unit operations are adapted from other sectors (primarily agriculture), where some simplifying assumptions about granular mechanics and flow performance do not translate well to a highly compressible and anisotropic material with nonlinear time- and stress-dependent properties. This work explores the shear and frictional properties of loblolly pine at multiple experimental test apparatus and particle scales to elucidate a property window that defines the shear behavior over a range of material attributes (particle size, size distribution, moisture content, etc.). In general, it was observed that the bulk internal friction and apparent cohesion depend strongly on both the stress state of the sample in granular shear testers and the overall particle size and distribution span. For equipment designed to characterize the quasi-static shear stress failure of bulk materials ranging from 50 to 1,000 ml in test volume, similar test results were observed for finely milled particles (50% passing size of 1.4 mm) with a narrow size distribution (span between 10 and 90% passing size of 0.9 mm), while stress chaining and over-torque issues persisted for the bench-scale test apparatus for larger particle sizes or widely dispersed sample sizes. Measurement of the anisotropic particle–particle friction ranged from coefficients of approximately 0.20 to 0.45 and resulted in significantly higher and more variable friction measurements for larger particle sizes and in perpendicular alignment orientations. To supplement these laboratory-scale properties, this work explores the flow of loblolly pine and Douglas fir through a pilot-scale wedge-shaped hopper and a screw feeder. For the gravity-driven hopper flow, the critical arching distance and mass discharge rate ranged from approximately 10 to 30 mm and 2 to 16 tons/hour, respectively, for both materials, where the arching distance depends strongly on the overall particle size and depends less on the hopper inclination angle. Comparatively, the auger feeder was found to be much more impacted by the size of the particles, where smaller particles had a more consistent and stable flow while consuming less power.
09 BIOMASS FUELS↗
On the Fidelity of Computational Models for the Flow of Milled Loblolly Pine: A Benchmark Study on Continuum-Mechanics Models and Discrete-Particle Models
The upstream of bioenergy industry has suffered from unreliable operations of granular biomass feedstocks in handling equipment. Computational modeling, including continuum-mechanics models and discrete-particle models, offers insightful understandings and predictive capabilities on the flow of milled biomass and can assist equipment design and optimization. This paper presents a benchmark study on the fidelity of the continuum and discrete modeling approaches for predicting granular biomass flow. We first introduce the constitutive law of the continuum-mechanics model and the contact law of the coarse-grained discrete-particle model, with model parameters calibrated against laboratory characterization tests of the milled loblolly pine. Three classical granular material flow systems (i.e., a lab-scale rotating drum, a pilot-scale hopper, and a full-scale inclined plane) are then simulated using the two models with the same initial and boundary conditions as the physical experiments. The close agreement of the numerical predictions with the experimental measurements on the hopper mass flow rate, the hopper critical outlet width, the material stopping thickness on the inclined plane, and the dynamic angle of repose, clearly indicates that the two methods can capture the critical flow behavior of granular biomass. The qualitative comparison shows that the continuum-mechanics model outperforms in parameterization of materials and wall friction, and large-scale systems, while the discrete-particle model is more preferred for discontinuous flow systems at smaller scales. Industry stakeholders can use these findings as guidance for choosing appropriate numerical tools to model biomass material flow in part of the optimization of material handling equipment in biorefineries.
Jin, Wencheng↗
Flowability of Crumbler Rotary Shear Size-Reduced Granular Biomass: An Experiment-Informed Modeling Study on the Angle of Repose
Biomass has potential as a carbon-neutral alternative to petroleum for chemical and energy products. However, complete replacement of fossil fuel is contingent upon efficient processes to eliminate undesirable characteristics of biomass, e.g., low bulk density, variability, and storage-induced quality problems. Mechanical size reduction via comminution is a processing operation to engineer favorable biomass flowability in handling. Crumbler rotary shear mill has been empirically demonstrated to produce more uniformly shaped particles with higher flowability than hammermilled biomass. This study combines modeling and experimentation to unveil fundamental understandings of the relation between granular particle characteristics and biomass flow behavior, which elucidate underlying mechanisms and guide selection of critical processing parameters. For this purpose, the impact of critical material attributes, including particle size (2–6 mm), particle shape (briquette, chip, clumped-sphere, cube, etc.), and surface roughness, on the angle of repose (AOR) of milled pine chips were investigated using discrete element method (DEM) simulations. Forest Concepts Crumbler rotary shear system is used to produce milled pine particles within the same size range considered in DEM simulations. AOR of different sets of these particles were measured experimentally to benchmark DEM results against experimental data. Specific energy consumption for the comminution of biomass with different particle size and moisture content are measured for technoeconomic analysis. Our results show that the smaller size (2 mm) of pine particle achieves better followability (i.e., smaller AOR) while the energy cost of comminution is significantly higher and bulk density is almost the same as the 6-mm pine particles. For the 2-mm particle size, Crumbles from veneer have better flow properties than Crumbles from chips. Contrarily, no significant difference was observed between the AOR of the two materials for the 6-mm particle size. Furthermore, from DEM simulations, mechanical interlocking between particles was found as a dominant factor in determining AOR of complex-shaped particles such as milled pine, which cannot be accurately captured by using simple particle shapes (e.g., mono-sphere) with a rolling resistance model. Conversely, clumped-sphere model alleviates this limitation without increasing computational cost significantly and can be used for accurate representation of biomass granular particles when simulating free-flow behavior.
09 BIOMASS FUELS↗