Search NASA⌕ Search

Engineering topics

Klouzek, Jaroslav

Publications and source records attributed to Klouzek, Jaroslav.

10 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Heat Transfer in Nuclear Waste Glasses: Measurements and Modeling of Thermal Radiation Properties

We measured and modeled near infrared extinction of nuclear waste glasses from 300 °C to 1150 °C to enable predictive radiation heat transfer and thermal conductivity estimates. A composition and redox informed model resolved contributions from key chromophores (Fe+2-O-Fe+3, V+4, free and bonded ?Si-OH groups) and, when present, spinel particles that can cause strong scattering. The model reproduced measured absorption from room temperature up to 1150 °C, with minor discrepancies near 1 µm (likely due to possible trace impurities) and 2.5 µm (linked to uncertainty in hydroxy groups). Spectra showed silicate melts were semitransparent mainly in the 0.5–4.0 µm window, responsible for radiation thermal conductivity that generally increases with increasing temperature. We quantified the dependence of effective thermal conductivity on dissolved water and provided distributions across >100 LAW/HLW/DFHLW melts at 1150 °C, supporting improved melter heat transfer modeling.

Ferkl, Pavel↗
DOE OSTI2021

In-situ X-ray and visual observation of foam morphology and behavior at the batch-melt interface during melting of simulated waste glass

We report to attain a basic understanding of the primary foam structure and behavior, which affects the heat and mass transfer and the efficiency of the glass melting process, we investigated the primary foam layer under the glass batch floating on molten glass. The primary foam affects mass transfer during batch melting, in turn affecting the melting process. The recently performed direct in-situ three-dimensional X-ray computed tomography of the batch melting in a laboratory-scale melter vessel allowed us to visualize the features of the reacting batch layer and the foam that develops at its bottom, though with an insufficient resolution of images. In this study, we obtained better temporal and spatial resolution using the two-dimensional X-ray radiography and visual observation of the structure and behavior of transient primary foam as it formed and decayed. As soon as the batch was charged onto the melt surface, foam bubbles began to evolve, grow, and coalesce, forming a primary foam layer, 5-10 mm thick, within tens of seconds. This foam layer was sustained by ongoing gas evolving reactions counterbalanced by bubble coalescence into cavities that moved sideways and escaped to the atmosphere. Eventually, the entire remaining batch turned into foam that gradually decayed at the melt surface. The decay rate agreed with literature observations of surface foam produced by secondary foaming.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Melting rate correlation with batch properties and melter operating conditions during conversion of nuclear waste melter feeds to glasses

The rate of conversion of nuclear waste melter feed to glass is affected by the selection of melter feed materials and by melter design and operation. The melting rate correlation (MRC) is an equation that relates the glass production rate with two types of variables: (1) feed and melt properties: conversion heat, cold-cap bottom temperature, and glass melt viscosity; and (2) melter design and operation parameters: melter geometry, melter operating temperature, and gas bubbling rate. The MRC shows good agreement for an extended melting-rate data set of high-level waste (HLW) melter feeds and a data set generated for low-activity waste (LAW) melter feeds. Laboratory observation of heated melter feed samples is often used to assess the cold-cap bottom temperature of HLW melter feeds (moderately foaming feeds), but this technique appears inadequate for LAW melter feeds (vigorously foaming feeds). For LAW feeds, an adequate assessment of the cold-cap bottom temperature was achieved using evolved gas analysis, which allows identification of the collapse of primary foam for oxidized feeds. This assessment shows that the cold-cap bottom temperature for vigorously foaming LAW feeds is higher than that for moderately foaming HLW feeds. When the results of MRC are compared, LAW feeds are generally less sensitive to the bubbling rate and melt viscosity, and more sensitive to the cold-cap bottom temperature than HLW feeds. The MRC qualifies as a promising tool to support the selection of melter feed materials and melter operating conditions, which is determined from expensive independent scaled melter experiments, and sophisticated mathematical models.

Lee, Seung Min↗
DOE OSTI2021

Through a glass darkly: In-situ x-ray computed tomography imaging of feed melting in continuously fed laboratory-scale glass melter

his study describes the first direct in-situ 3-D observation of a steady-state melting process by imaging a laboratory-scale slurry-fed glass melter in operation by x-ray computed tomography. Features of the reacting glass-feed, the foam layer underneath, and cavities in the glass melt pool are reconstructed in three-dimensional images. A slurry pool formed in a deep central caldera of dense dried feed, which penetrated into the glass melt. Slurry overflow from the caldera led to fast-dried and highly porous feed structure. A thin layer of foam separated the caldera from the melt. Bubbles ?5-15 mm in diameter were seen to grow beneath the reacting feed and move through the melt to escape at the edge. Pore morphology is benchmarked against computed tomography scans of a pellet of reacting simulated waste glass feed, and evolved gas analysis describes the gases generated as a function of temperature. Cooling artifacts are imaged and compared to previous studies of quenched cold caps. Detailed understanding of processes occurring during the conversion process in and below the reacting feed layer is necessary for the development of representative models of the melting process.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Heat transfer from glass melt to cold cap: Computational fluid dynamics study of cavities beneath cold cap

Efficient glass production depends on the continuous supply of heat from the glass melt to the floating layer of batch, or cold cap. Computational fluid dynamics (CFD) are employed to investigate the formation and behavior of gas cavities that form beneath the batch by gases released from the collapsing primary foam bubbles, ascending secondary bubbles, and in the case of forced bubbling, from the rising bubbling gas. The gas phase fraction, temperature, and velocity distributions below the cold cap are used to calculate local and average heat transfer rates as a function of the bubbling rate. It is shown that the thickness of the cavities is nearly independent of the cold cap shape and the amount of foam evolved during batch conversion. Furthermore, it is ~7 mm and up to ~15 mm for the cases without and with forced bubbling used to promote circulation within the melt, respectively. Using computed velocity and temperature profiles, the melting rate of the simulated high-level nuclear waste glass batch was estimated to increase with the bubbling rate to the power of ~0.3 to 0.9, depending on the flow pattern. The simulation results are in good agreement with experimental data from laboratory- and pilot-scale melter tests.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Effect of water vapor and thermal history on nuclear waste feed conversion to glass

Water affects the glass melting process by interacting with the foam layer at the glass melt surface and by influencing the batch conversion reactions. Water vapor from the nuclear waste slurry feed maintains a high water vapor pressure in the melter atmosphere. To investigate to what extent water vapor affects the vitrification of nuclear waste in joule-heated, cold-top melters, a series of feed expansion experiments were performed under humid and dry atmospheres using samples of low-activity waste (LAW) melter feed simulants. Melting of feed pellets in the presence of water vapor slightly decreased the temperature of primary foam onset, but did not significantly affect the feed volume expansion by foaming or the foam-collapse temperature. Sets of feed expansion experiments and evolved gas analyses were also performed to check the effect of thermal history on LAW feed samples tested as direct slurry, loose powder, and slow- and fast-dried pellets.

Marcial, Jose↗
DOE OSTI2020

Viscosity of glass-forming melt at the bottom of high-level waste melter feed cold caps: Effects of temperature and incorporation of solid components

At the final stages of conversion of melter feed (glass batch) to molten glass, the transient glass-forming melt becomes a continuous liquid phase encapsulating dissolving solid particles and gas bubbles that produce primary foam at the bottom of the cold cap (the reacting melter feed in an electric glass melting furnace). The glass-forming melt viscosity plays a dominant role in primary foam formation, stability, and eventual collapse, thus affecting the rate of melting (the glass production rate per cold cap area). For several melter feeds designed for nuclear waste vitrification, we have traced the glass-forming melt viscosity during the final stages of feed-to-glass conversion as it changes in response to changing temperature and composition (resulting from dissolving solid particles). Starting with a relatively low values at the moment when the melt connects, melt viscosity reaches maximum within the primary foam layer and then decreases to its final melter-operating temperature value. We paid a particular attention to the cold-cap bottom—the boundary between the primary foam layer and the thermal boundary layer—where the melt viscosity affects the rate of melting predominantly through its effect on the temperature at which primary foam is collapsing.

Lee, Seung Min↗
DOE OSTI2020

Modeling batch melting: Roles of heat transfer and reaction kinetics

Development of mathematical models of heat and mass transfer in glass-melting furnaces began in the 1970s and progressed rapidly with advances in sophisticated experimental/numerical techniques and increasing computational power. Today, practically all newly built or rebuilt furnaces are optimized with these models to meet stringent quality requirements, reduce the unit costs of manufacturing, or control emissions. One remaining hurdle is to model the batch-to-glass conversion accurately enough to reliably assess the glass production rate. This article summarizes two key aspects of the batch-conversion modeling—the heat transfer and the kinetics of conversion—and reviews the current state-of-the-art approaches to simulating them. We critically examine the advantages of the commonly used heat transfer approach, but also explain that its predictive capabilities are significantly restricted by the dependence of batch thermal properties on the time-temperature history. We argue that kinetic approaches to the batch-conversion modeling would offer a significant improvement when coupled with the heat transfer approach. Finally, we summarize key areas requiring further research on the way toward a realistic model of the batch blanket.

Pokorny, Richard↗