Search NASA⌕ Search

Engineering topics

Kmiec, Steven

Publications and source records attributed to Kmiec, Steven.

18 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

A New Class of Oxyhalide Solid Electrolytes NaNbCl 6‐2x O x for Solid‐state Sodium Batteries

Abstract Sodium‐based batteries are gaining momentum due to the abundance and lower cost of sodium compared to lithium. Solid‐state sodium batteries can also provide further safety advantages. However, sodium‐based solid‐state electrolytes (SSEs) that meet all the rigorous requirements, such as high ionic conductivity, oxidative stability with the cathode, and ease of processability, are lacking. We present here a new class of sodium‐based oxyhalide electrolytes NaNbCl 6‐2x O x with a facile mechanochemical synthesis. The oxyhalide NaNbCl 4 O exhibits close to two orders of magnitude higher ambient‐temperature sodium‐ion conductivity (1.03×10 −4 S cm −1 ) compared to the halide counterpart NaNbCl 6 (3×10 −6 S cm −1 ). Structural motifs unique to the oxygen content in NaNbCl 6‐2x O x are identified with 23 Na and 93 Nb magic angle spinning nuclear magnetic resonance (MAS NMR) spectroscopy and x‐ray diffraction (XRD). Solid‐state sodium batteries assembled with NaNbCl 4 O electrolyte and the cobalt‐ and nickel‐free layered Na 0.70 Fe 0.3 Mn 0.65 Al 0.05 O 2 cathode exhibit a maximum discharge capacity of 155 mAh g −1 with good cycle life at ambient temperature.

Kmiec, Steven↗
DOE OSTI2024

A New Class of Oxyhalide Solid Electrolytes NaNbCl 6‐2x O x for Solid‐state Sodium Batteries

Abstract Sodium‐based batteries are gaining momentum due to the abundance and lower cost of sodium compared to lithium. Solid‐state sodium batteries can also provide further safety advantages. However, sodium‐based solid‐state electrolytes (SSEs) that meet all the rigorous requirements, such as high ionic conductivity, oxidative stability with the cathode, and ease of processability, are lacking. We present here a new class of sodium‐based oxyhalide electrolytes NaNbCl 6‐2x O x with a facile mechanochemical synthesis. The oxyhalide NaNbCl 4 O exhibits close to two orders of magnitude higher ambient‐temperature sodium‐ion conductivity (1.03×10 −4 S cm −1 ) compared to the halide counterpart NaNbCl 6 (3×10 −6 S cm −1 ). Structural motifs unique to the oxygen content in NaNbCl 6‐2x O x are identified with 23 Na and 93 Nb magic angle spinning nuclear magnetic resonance (MAS NMR) spectroscopy and x‐ray diffraction (XRD). Solid‐state sodium batteries assembled with NaNbCl 4 O electrolyte and the cobalt‐ and nickel‐free layered Na 0.70 Fe 0.3 Mn 0.65 Al 0.05 O 2 cathode exhibit a maximum discharge capacity of 155 mAh g −1 with good cycle life at ambient temperature.

Kmiec, Steven↗
DOE OSTI2024

Mitigating Sodium Ordering for Enhanced Solid Solution Behavior in Layered NaNiO 2 Cathodes

Abstract The O‐type layered nickel oxides suffer from undesired cooperative Jahn–Teller distortion stemming from Ni 3+ ions and undergo multiple biphasic structural transformations during the insertion/extraction of large Na + ions, posing a significant challenge to stabilize the structural integrity. We present here a systematic investigation of the impact of substituting 5 % divalent (Mg 2+ ) or trivalent (Al 3+ or Co 3+ ) ions for Ni 3+ to alleviate Na + ion ordering and perturb the Jahn–Teller effect to enhance structural stability. We gauge a fundamental understanding of the Mg−O and Na−O or Mg−O−Na bonding interactions, noting that the ionicity of the Mg−O bond deshields the electronic cloud of oxygen from Na + ions. Furthermore, calculations of the Van Vleck distortion modes reveal a relaxation of NiO 6 octahedra from Jahn–Teller distortion and a reduced electron density at the interlayer with Mg 2+ substitution. Long‐range ( operando X‐ray diffraction) and short‐range (magic angle spinning nuclear magnetic resonance) structural analyses provide insights into reduced ordering, allowing a stable continuous solid solution. Overall, Mg‐substitution results in a high‐capacity retention of ~96 % even after 100 cycles, showcasing the potential of this strategy for overcoming the structural instabilities and enhancing the performance of sodium‐ion batteries.

Sada, Krishnakanth↗
DOE OSTI2024

Mitigating Sodium Ordering for Enhanced Solid Solution Behavior in Layered NaNiO 2 Cathodes

The O-type layered nickel oxides suffer from undesired cooperative Jahn–Teller distortion stemming from Ni 3+ ions and undergo multiple biphasic structural transformations during the insertion/extraction of large Na + ions, posing a significant challenge to stabilize the structural integrity. We present here a systematic investigation of the impact of substituting 5 % divalent (Mg 2+ ) or trivalent (Al 3+ or Co 3+ ) ions for Ni 3+ to alleviate Na + ion ordering and perturb the Jahn–Teller effect to enhance structural stability. Here, we gauge a fundamental understanding of the Mg−O and Na−O or Mg−O−Na bonding interactions, noting that the ionicity of the Mg−O bond deshields the electronic cloud of oxygen from Na + ions. Furthermore, calculations of the Van Vleck distortion modes reveal a relaxation of NiO 6 octahedra from Jahn–Teller distortion and a reduced electron density at the interlayer with Mg 2+ substitution. Long-range (operando X-ray diffraction) and short-range (magic angle spinning nuclear magnetic resonance) structural analyses provide insights into reduced ordering, allowing a stable continuous solid solution. Overall, Mg-substitution results in a high-capacity retention of ~96 % even after 100 cycles, showcasing the potential of this strategy for overcoming the structural instabilities and enhancing the performance of sodium-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2023

Polycarbonate‐Based Solid‐Polymer Electrolytes for Solid‐State Sodium Batteries

Solid-polymer electrolytes comprised of polypropylene carbonate (PPC) and varied sodium bis(fluorosulfonyl)imide (NaFSI) salt concentrations are investigated for implementation as a conductive solid polymer electrolyte into solid-state cathode composites utilizing a sodium-layered oxide active material. The ionic conductivity generally increases with NaFSI salt content, reaching ≈1 mS cm −1 at 80 °C at the highest salt concentration (PPC:NaFSI = 0.5:1). Through an all-in-one slurry casting method, Na 2/3 Ni 1/3 Mn 2/3 O 2 cathode composites are fabricated in which the dispersed PPC electrolyte acts as the primary binder. Enabled by a bilayer polymer electrolyte system, cycling performance with the PPC cathode electrolyte is optimized with respect to salt concentration and anode material. The best cyclability is achieved with a moderate salt concentration electrolyte (PPC:NaFSI = 5:1), showcasing an initial capacity of 83 mA h g −1 with a remarkable 80% capacity retention after 150 cycles at C/5 rate and 60 °C. The superior performance of the lower salt concentration electrolyte is attributed to better electrochemical stability, as confirmed by linear sweep voltammetry and online electrochemical mass spectrometry measurements. In conclusion, these results underscore the potential of carbonate-based polymer electrolytes and the importance of balancing electrolyte conductivity and stability in cell design.

25 ENERGY STORAGE↗
DOE OSTI2022

An electrochemically stable homogeneous glassy electrolyte formed at room temperature for all-solid-state sodium batteries

All-solid-state sodium batteries (ASSSBs) are promising candidates for grid-scale energy storage. However, there are no commercialized ASSSBs yet, in part due to the lack of a low-cost, simple-to-fabricate solid electrolyte (SE) with electrochemical stability towards Na metal. In this work, we report a family of oxysulfide glass SEs (Na 3 PS 4-x O x , where 0 < x ≤ 60) that not only exhibit the highest critical current density among all Na-ion conducting sulfide-based SEs, but also enable high-performance ambient-temperature sodium-sulfur batteries. By forming bridging oxygen units, the Na 3 PS 4-x Ox SEs undergo pressure-induced sintering at room temperature, resulting in a fully homogeneous glass structure with robust mechanical properties. Furthermore, the self-passivating solid electrolyte interphase at the Na|SE interface is critical for interface stabilization and reversible Na plating and stripping. The new structural and compositional design strategies presented here provide a new paradigm in the development of safe, low-cost, energy-dense, and long-lifetime ASSSBs.

25 ENERGY STORAGE↗
DOE OSTI2020

Glass transition temperature studies of planetary ball milled glasses: Accessing the rapidly cooled glassy state in Na 4 P 2 S 7-x O x , 0 ≤ x ≤ 7, Oxy-thio phosphate glasses

This paper details the very first in-depth study of the glass transition temperature (T g ) for planetary balled milled (PBM) Na 4 P 2 S 7-x O x (NaPSO), where 0 ≤ x ≤ 7, glasses. For 0 ≤ x ≤ 5, fully amorphous, homogeneous, and chemically reacted compositions can be prepared. For samples with 5 < x ≤ 7, partially amorphous but fully chemically reacted glass-ceramics can be produced. The reproducible, thermally cyclable onset T g and the onset crystallization temperature, T c , were investigated as a function of the composition and of the short-range order (SRO) structures of the glasses. Additionally, we examined the extreme sub-T g exothermic relaxations present due to the high energy milling processing and correspondingly high effective quenching rate. Using a differential scanning calorimeter (DSC) and scanning from well below the onset T g , the glasses are observed to relax exothermally below T g . The integrated relaxation enthalpy, ΔH rel , is ~ 0 for the x = 2 glass, but is significantly exothermic for lower and higher values of x. Once the high fictive state of these glasses has been erased by scanning to above the T g , but below the T c of the glass, the DSC scans of the glasses recover normal behavior for a normally cooled glass without any relaxation exotherm. The T g s of these glasses remain relatively constant for 0 ≤ x ≤ 3, but for glasses with 3 < x ≤ 5, T g increases sharply following the combined effects of the phosphate chain length increasing caused by the formation of bridging oxygens and the increasing concentration of more charge dense non-bridging oxygens (NBOs). For x > 5, both T g and Tc decrease sharply, becoming nearly identical at x = 7 where glass formation essentially ceases. For smaller values of x, T c increases with both chain length and the structural complexity of the composition but decreases sharply for glass-ceramics of x > 5.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Glass formation and structure of melt quenched mixed oxy-sulfide Na 4 P 2 S 7-x O x glasses for 0 ≤ x ≤ 5

The structures of Na 4 P 2 S 7-x O x , 0 ≤ x ≤ 5, glasses were investigated using melt quench (MQ) samples. The short-range order (SRO) structures of these glasses were examined using a combination of Raman, Fourier Transform Infrared (FT-IR), and 31 P Magic Angle Spinning NMR ( 31 P MAS NMR) spectroscopies to determine how oxygen is incorporated into the sulfide structure. Using vibrational spectroscopy, semi-quantitative 31 P MAS NMR, and charge balancing, a complete compositional map of all the SRO structures present in these glasses has been generated. From these findings, full incorporation of the oxygen into the sulfide melt was found to occur across the compositional series through a structural disproportionation reaction where oxygen systematically replaces bridging sulfurs (BSs), before replacing the remaining non-bridging sulfurs (NBSs). Under the melting and quenching conditions used in this study, it was found that the melts crystallize too quickly to form homogeneous crystallite-free glasses for x > 5.

36 MATERIALS SCIENCE↗
DOE OSTI2019

LiPON and NaPON glasses: A study of the ammonolysis of lithium and sodium metaphosphate melts

Metaphosphate glasses such as LiPO 3 and NaPO 3 are known to incorporate nitrogen in the molten state under NH 3 flow to form (Li/Na)PON glasses through the reaction: (Li/Na)PO 3 + x NH 3 → (Li/Na)PO 3–(3 x /2) N x + (3 x /2)H 2 O, by partially replacing two-coordinated oxygen with two- and three-coordinated nitrogen. After nitridation, the glasses exhibit improved properties such as increased working range, chemical durability, and ionic conductivity. In this study, LiPO 3 and NaPO 3 glasses were prepared by the conventional melting and casting method and used as base glasses for the ammonolysis procedure. The nitridation processes were carried out by remelting the base glasses at temperatures up to 780°C, under a constant NH 3 flow. The effects on the nitrogen content in the resulting (Li/Na)PON glasses caused by different processing times and masses of powder and/or bulk materials were investigated. Nitridation was successfully confirmed by CNHS chemical analyses, Raman spectroscopy, and Differential Scanning Calorimetry. Mass loss measurements after the ammonolysis process and Raman spectroscopy were used to quantify the nitrogen content into the glass structure. A new approach using a specific Raman normalization, (P–N<)/(O–P–O) sym , has been demonstrated as a reliable, simple, and fast way to determine the amounts of N incorporated to metaphosphate glass structures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗