Search NASA⌕ Search

Engineering topics

Knolker, Matthias

Publications and source records attributed to Knolker, Matthias.

4 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Resistive wall tearing mode disruptions in DIII-D and ITER tokamaks

Disruptions are a serious problem in tokamaks, in which thermal and magnetic energy confinement is lost. This paper uses data from the DIII-D experiment, theory, and simulations to demonstrate that resistive wall tearing modes (RWTMs) produce the thermal quench (TQ) in a typical locked mode shot. Analysis of the linear RWTM dispersion relation shows the parameter dependence of the growth rate, particularly on the resistive wall time. Linear simulations of the locked mode equilibrium show that it is unstable with a resistive wall and stable with an ideally conducting wall. Nonlinear simulations demonstrate that the RWTM grows to sufficient amplitude to cause a complete thermal quench. The RWTM growth time is proportional to the thermal quench time. Here, the nonlinearly saturated RWTM magnetic perturbation amplitude agrees with experimental measurements. The onset condition is that the q = 2 rational surface is sufficiently close to the resistive wall. Collectively, this identifies the RWTM as the cause of the TQ. In ITER, RWTMs will produce long TQ times compared to present-day experiments. ITER disruptions may be significantly more benign than previously predicted.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Pellet triggering of edge localized modes in low collisionality pedestals at DIII-D

Edge localized modes (ELMs) are triggered using deuterium pellets injected into plasmas with ITER-relevant low collisionality pedestals, and the resulting peak ELM energy fluence is reduced by approximately 25%–50% relative to natural ELMs destabilized at similar pedestal pressures. Cryogenically frozen deuterium pellets are injected from the low-field side of the DIII-D tokamak at frequencies lower than the natural ELM frequency, and heat flux is measured by infrared cameras. Ideal MHD pedestal stability calculations show that without pellet injection, these low collisionality pedestals were limited by their current density (peeling-limited) rather than their pressure gradient (ballooning-limited). ELM triggering success correlates strongly with pellet mass, consistent with the theory that a large pressure perturbation is required to trigger an ELM in low collisionality discharges that are far from the ballooning stability boundary. For sufficiently large pellets, both instantaneous and time-integrated ELM energy deposition measured by infrared cameras is reduced with respect to naturally occurring ELMs at the inner strike point, which is the position where it is largest for natural ELMs. Energy fluence at the outer strike point is less effected. Cameras observing both heat flux and D-alpha emission often find significant toroidally asymmetric striations in the outboard far scrape-off layer resulting from ELMs that are triggered by pellets. Toroidal asymmetries at the inner strike point are similar between natural and pellet-triggered ELMs, indicating that the reduction in peak heat flux and total fluence at that location is robust for the conditions reported here.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Development of an integrated core–edge scenario using the super H-mode

An optimized pedestal regime called the super-H (SH) mode is leveraged to couple a fusion relevant core plasma with a high density scrape-off layer appropriate for realistic reactor power exhaust solutions. Recent DIII-D experiments have expanded the operating space of the SH regime using advanced control algorithms and investigated optimization of impurity seeding, deuterium gas puffing, and 3D magnetic perturbations. Simultaneous real-time control of the pedestal density and radiated power with in-vessel coils and nitrogen seeding enable optimal coupled divertor and pedestal conditions. Four case studies are analysed with varied levels of radiated power in the divertor volume ranging from 0 (no seeding) to 8.5 MW radiated from carbon and nitrogen emission. Plasmas with a 4.5 MW radiated power target establish a radiative mantle, leading to divertor temperatures of ~16 eV while maintaining SH-mode, and with only marginal impact on the pedestal and core performance. Increased levels of N 2 seeding with a 7.5 MW radiated power target facilitate detachment onset and divertor temperatures <5 eV, with no degradation in stored energy and the operational point remaining inside the SH-mode channel for $ > 2.5{\tau }_{\text{E}}$. Finally, a 8.5 MW radiated power target leads to partial detachment, which is so far associated with the loss of access to SH-mode pedestal conditions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗