How inversion relates to disordering tendencies in complex oxides
The energy to invert the cation structure of a complex oxide correlates with the energy to disorder it.
Engineering topics
Publications and source records attributed to Kocevski, Vancho.
The energy to invert the cation structure of a complex oxide correlates with the energy to disorder it.
Uranium dioxide (UO 2 ) is the primary nuclear fuel in light water reactors, and its excess neutronic reactivity can be controlled by adding burnable absorbers, such as Gd 2 O 3 . This burnable absorber has a large neutron absorption cross-section, lowering the high reactivity of the reactor's initial fuel load. However, there needs to be more understanding of how added Gd 2 O 3 influences the properties of UO 2 under irradiation. To understand the behavior of defects and fission gas in the UO 2 /Gd 2 O 3 system under irradiation, we use cluster dynamics modeling supported by density functional theory calculations. First, we calculate the formation energies of Gd point and cluster defects, and evaluate the temperature-dependent defect concentrations using the defect formation energies and entropies. We show that Gd is soluble in UO 2 , introducing a negative charge in the system. Using this information, we adapted the cluster dynamics code Centipede to model the influence of Gd on U self-diffusion and Xe diffusion in UO 2 with 10 wt% Gd 2 O 3 . Also, we analyzed the Xe diffusion as a function of Gd 2 O 3 concentration, showing that the Xe diffusivity is decreased, which means that the athermal diffusivity due to electronic stopping persists at higher temperatures. In conclusion, the decrease in Xe diffusion means that more Xe stays in the matrix, decreasing the Xe release, and lowering its influence of fission gas release on the thermomechanical properties of UO 2 .
Uranium mononitride (UN) is a promising nuclear fuel that combines the advantageous properties of readily used UO 2 and uranium alloys, such as high melting temperature and high uranium density, and thermal conductivity, respectively. A better understanding of UN behavior at operating temperatures can be obtained from finite temperature data, such as elastic properties. To get this information, ab initio molecular dynamics (AIMD) simulations were performed at five different temperatures using constant volume (NVT) and constant pressure (NPT) ensembles. Initially, the performance of PBE functional in reproducing experimental crystallographic properties and magnetic ordering is assessed. The finite temperature phonon dispersions are calculated using NVT simulation results, which show a softening of the phonon modes with increasing temperature. The NPT results are used to obtain the thermal expansion of UN and finite temperature electronic properties. The calculated thermal expansion is compared with our measurements using neutron diffraction. Additionally, the temperature dependent elastic properties of UN are evaluated using the strain-stress method in AIMD simulations, indicating that UN becomes softer and more compressible with increasing temperature. Also, the calculated Young’s modulus slope is in very good agreement with the experiment. The finite temperature heat capacity and electronic thermal conductivity are calculated from AIMD simulations, which are in better agreement with the experiment than the heat capacity and thermal conductivity calculated using the structures relaxed at 0K. Finally, the thermal diffusivity from AIMD has opposite temperature dependence compared to experimental results, which we argued comes from the underestimated electronic thermal conductivity.
The thermochemical details of fabricating uranium nitride (UN) by ammonolysis of uranium tetraflouride (UF 4 ) were determined using density functional theory (DFT) and CALculation of PHAse Diagrams (CALPHAD) computational methods. The thermochemical data of all binary, ternary, and quaternary U-H-N-F phases were computed using DFT, and the data for the phases that have not been measured experimentally, including UN 2 and NH 4 F(g), were combined with existing experimentally-determined data for CALPHAD modeling. The DFT data were benchmarked using experimental Gibbs energy of reaction and experimental thermochemical data for individual species. Phase diagrams relevant to the ammonolysis reaction are depicted, showing regions of stability for solid U-N, U-F and U-N-F phases. An unidentified phase produced in a previous experiment was identified as UN 0.95 F 1.2 (UNF) by comparing its X-ray diffraction spectrum to the experimental spectrum, and its formation during the fabrication of UN from UF 4 is supported by the simulated phase diagram. Here, it is calculated that UN 2 can be produced by the ammonolysis of UF 4 , but requires elevated temperatures, high NH 3 (g) partial pressure, and large amounts of flowing NH 3 (g) to avoid solid flu oride impurities in the uranium nitride. Likewise, U 2 N 3 can be produced instead at temperatures greater than 980 K. The use of silane (SiH 4 ) gas was investigated as a potential additive in the ammonolysis fabrication route to speed removal of fluorine. The addition of SiH 4 (g) offers little advantage to the removal of fluorine, and adds the complication of Si 3 N 4 formation. The use of DFT to fill in missing data to perform CALPHAD calculations demonstrated here allows for the determination of more comprehensive and trustworthy phase diagrams than the use of existing experimental data alone.
We report that atomic-scale modeling of thermophysical and defect properties of uranium mononitride (UN) plays an important role in establishing a better understanding and improved models of UN fuel performance. Having an accurate interatomic potential is crucial for generating reliable data at finite temperatures using molecular dynamic simulations. We report a new interatomic potential for UN, based on a combination of many-body and pairwise interactions, a simple form that we later show could be easily adapted to include Xe-U and Xe-N interactions, i.e., generating a U-N-Xe interatomic potential. The potential was fitted to experimental thermal expansion and single crystal elastic constants, as well as Frenkel, Schottky, anti-Schottky, and antisite pair reaction energies from density functional theory (DFT) calculations. Using the potential, we successfully reproduced experimental lattice parameters, thermal expansion, single crystal elastic constants, and temperature dependent heat capacity. The potential also performs reasonably well in reproducing the energy of the aforementioned stoichiometric defect reactions and defect migration barriers calculated using DFT. However, the potential underestimates the energy difference between the tetrahedral and dumbbell uranium interstitials, and a more complex potential form might be needed to overcome this issue. The potential was also used to predict UN single crystal elastic constants and elastic properties at different temperatures, showing that UN becomes softer and more compressible with increasing temperature. We also compare our potential against literature data from previous empirical potentials, demonstrating similar or better behavior depending on the property of interest. To enable the simulation of Xe in UN a Buckingham potential has been fitted to DFT-derived Xe incorporation energies. The potential was then used to determine the activation energy for Xe diffusion due to various Xe-containing defects, with {XeU : VU} exhibiting the lowest activation energy.
Abstract not provided.
Uranium mononitride (UN) is a promising nuclear fuel that combines the advantageous properties of readily used UO 2 and uranium alloys. Various properties of UN have been previously studied using different density functional theory (DFT) methodologies; however, there are still inconsistencies when it comes to the dynamical stability and defect properties of UN. We address these inconsistencies by studying the UN phonons and defect properties using DFT calculations employing two generalized gradient approximation (GGA) exchange-correlation functionals: PBE and AM05, with and without an added on-site Coulomb repulsion term (+U). Furthermore, we investigate the importance of spin-orbit coupling (SOC) when calculating the properties of UN. We use the different methodologies to determine the preference of UN to have antiferromagnetic (AFM) ordering, as seen in experiments, or ferromagnetic (FM) ordering of the uranium spins. We compare the crystallographic properties, density of states, the DFT X-ray photoelectron spectra and phonon dispersions calculated using the different methodologies. We demonstrate that GGA + U reproduces the AFM ordering in UN, but the crystal structure is dynamically unstable. We also show that magnetic ordering is important in finding the lowest energy defective structure, and that SOC has a distinct influence on the energy of the different uranium interstitial defects. Lastly, we discuss the point defect formation energies under U-rich and N-rich conditions, and the stoichiometric formation energies calculated with the different methodologies, providing insight into the observed tendency for forming hypostoichiometric UN.
U 3 Si 2 is of interest to the nuclear industry as a candidate fuel material due to its high uranium density and high thermal conductivity. However, it has been observed to react with hydrogen, resulting in material decrepitation. As a result, it is important to understand the thermodynamics of the U 3 Si 2 -H system. In this study, the thermodynamics of the hydrogen absorption reaction of USi were determined experimentally using Sievert’s gas absorption and related to crystallographic evolution with hydrogen content using X-ray diffraction. Experimentally-determined thermodynamic parameters were compared with results from density functional theory modeling. Results from this study were also compared with those determined in previous work. Sievert’s gas absorption results were used to develop the pressure-composition-temperature (PCT) curves of the U 3 Si 2 -H system. It was found that the hydride phase exhibited a maximum stoichiometry between U 3 Si 2 H 1.8 and U 3 Si 2 H 2 . The two-phase region for hydride formation from U 3 Si 2 exhibited a miscibility gap with a critical temperature between 623 and 673 K, as calculated from the PCT curves. Analysis of the PCT curves also showed that both the enthalpy and entropy of the hydrogen absorption reaction increased with hydrogen content but were lower than the values for uranium trihydride formation from uranium metal. The enthalpy of reaction for hydrogen absorption was calculated to range between -86.9 and -94.8 kJ mol -1 , while the entropy of reaction was calculated to range between 101.9 and 138.8 J mol -1 K -1 . Furthermore, DFT modeling of the thermoydnamic stability of the USi hydride phases yielded a decomposition temperature of U 3 Si 2 H 2 of approximately 600 K, which was consistent with the experimental results. Similarly, the DFT-calculated enthalpy and entropy of reaction to form USiH were determined to be -106.5kJ mol and 121.8J mol -1 K -1 , respectively, which were both in close agreement with the experimentally-determined values.
Explore the source record for details and available documents.
A series of Ca-containing lanthanide thiophosphates has been obtained and their structural evolution from 3D for LnPS 4 and Cs 0.3 (Ln 0.7 Ca 0.3 )PS 4 to 2D in Cs 0.5 (Ln 0.5 Ca 0.5 )PS 4 was shown as a function of Ca content. The first series with an idealized formula of Cs 0.3 (Ca 0.3 Ln 0.7 )PS 4 crystallizes in the R3¯m with combining macron]m space group and belongs to a new structure type that consists of a channel containing [(Ca 0.3 Ln 0.7 )PS 4 ] 0.3– framework, where the channels are occupied by severely disordered Cs + cations. A second new series with formula Cs 0.5 (Ca 0.5 Ln 0.5 )PS 4 crystallizes in the monoclinic C2/c space group and exhibits a layered structure consisting of [(Ca 0.5 Ln 0.5 )PS 4 ] 0.5– layers with Cs + cations located between the layers for charge balance. Together with the parent structure type, LnPS 4 , these three structure types illustrate how the LnPS 4 structure changes with Cs + cation incorporation, reducing its dimensionality from 3D to 2D. The magnetic properties of Cs 0.3 [(Ca 0.3 Ce 0.7 )PS 4 ] and Cs 0.3 [(Ca 0.3 Pr 0.7 )PS 4 ] were studied and revealed no magnetic transition down to 2 K.
Spinel compounds, with the general chemical formula AB 2 O 4 , are a wide class of materials, where A and B can be a variety of cations, providing this structure with a great deal of functional flexibility and giving rise to its considerable scientific interest. Recently, a spinel with the general formula ABB'O 4 has been predicted, increasing the possible usability of the spinels due to the higher cation diversity in the so-called double spinel structure. In this study, we use density functional theory calculations to predict if double spinels can be formed between experimentally synthesized normal and inverse single spinels. Our computations reveal that 49 double spinels have negative mixing enthalpies and are thus thermodynamically stable, with most of the stable compounds being formed from one of two distinct cation orderings. We show that the 17 different cations that form the different double spinels have a preferred site, tetrahedral or octahedral, except for Mn, Fe and Co which can occupy both sites interchangeably. We also study the relation between mixing enthalpies and cation-specific properties, as well as ways to classify the double spinels into distinct types and spinel groups depending on the cation ordering and cation oxidation states, respectively. Furthermore, by applying the Sure Independence Screening and Sparsifying Operator (SISSO) approach on the coordination-dependent ionic radii of the elemental constituents, we show that an interplay of local strain and electrostatic dominated terms can be used to separate the double spinels into distinct structural types depending on the cation order and their oxidation states.
Abstract Spinels represent an important class of technologically relevant materials, used in diverse applications ranging from dielectrics, sensors and energy materials. While solid solutions combining two “single spinels” have been explored in a number of past studies, no ordered “double” spinels have been reported. Based on our first principles computations, here we predict the existence of such a double spinel compound MgAlGaO 4 , formed by an equimolar mixing of MgAl 2 O 4 normal and MgGa 2 O 4 inverse spinels. After studying the details of its atomic and electronic structure, we use a cluster expansion based effective Hamiltonian approach with Monte Carlo simulations to study the thermodynamic behavior and cation distribution as a function of temperature. Our simulations provide strong evidence for short-ranged cation order in the double spinel structure, even at significantly elevated temperatures. Finally, an attempt was made to synthesize the predicted double spinel compound. Energy Dispersive X-ray Spectrometry and X-ray diffraction Rietveld refinements were performed to characterize the single-phase chemical composition and local configurational environments, which showed a favorable agreement with the theoretical predictions. These findings suggest that a much larger number of compounds can potentially be realized within this chemical space, opening new avenues for the design of spinel-structured materials with tailored functionality.
Not Available
Here single crystals of Rb 0.74 Ga 6.62 Ti 0·38 O 11 (RGTO) were grown from a mixed RbCl–RbF flux at 850 °C. The compound crystallizes in the RbGa 7 O 11 structure type, which is reminiscent of the hollandite and β-Ga 2 O 3 structure types. RGTO crystallizes in the monoclinic space group P2/m with lattice parameters a = 8.3355 (8) Å, b = 3.0286 (3) Å, c = 9.5028 (9) Å, and β = 114.620 (3)°. The crystal structure of RGTO is comprised of GaO 6 and mixed (Ga/Ti)O 6 octahedra and GaO 4 tetrahedra connected in a complex three-dimensional, anionic framework exhibiting eight-sided channels that are occupied by disordered Rb cations required for charge balance. First-principles calculations in the form of density functional theory were performed, which indicated the complex to be a charge transfer semiconductor.
Abstract Single crystals of CsGa 7 O 11 , RbGa 7 O 11 , and RbGa 4 In 5 O 14 were grown from alkali halide melts and their structures were characterized by single crystal and powder X‐ray diffraction. CsGa 7 O 11 and RbGa 7 O 11 adopt the same structure type, reminiscent of the hollandite structure type, as it contains nearly rectangular channels made up of two dimers of edge‐sharing GaO 6 octahedra, and two corner‐sharing octahedron/tetrahedron pairs. The structure of RbGa 4 In 5 O 14 is more complex and is comprised of indium octahedra, gallium trigonal bipyramids, and gallium tetrahedra, and contains similar sized tunnels as CsGa 7 O 11 and RbGa 7 O 11 . CsGa 7 O 11 and RbGa 4 In 5 O 14 were further characterized by TGA, ion exchange experiments, and DFT studies revealing that both structures are thermodynamically stable up to 850°C; however, CsGa 7 O 11 decomposes to GaO(OH) xH 2 O when heated in warm aqueous solutions. CsGa 7 O 11 undergoes ion exchange in both an aqueous solution of RbCl and a RbNO 3 melt, as predicted by DFT studies, where the ion exchange is more extensive in the RbNO 3 melt.
Due to its high thermal conductivity and uranium density, U 3 S i2 has been considered as a candidate for use as an accident tolerant fuel (ATF). In order to fully assess its suitability and performance as a fuel, the impact of fission products (FPs) on the stability and performance of U 3 Si 2 must be investigated. The interactions of FPs and U 3 Si 2 have had relatively little study until now and require experimental and computational examination. U 3 Si 2 was doped with individual FPs to explore U-Si-FP interactions and phase equilibria that may impact the performance of the ATF during irradiation. Elemental Ce, Mo, Y, or Zr were used to individually dope U 3 Si 2 at a concentration of 5 wt% FP. A diffusion couple of a 1:1 Mo:Zr alloy and U 3 Si 2 was heated to 1200 °C in order to consider the impacts of multiple FPs on the stability and structure of the fuel. Samples were characterized for FP solubility and secondary phase formation using electron microscopy, energy dispersive spectroscopy, and x-ray diffraction. First principles density functional theory calculations complemented the experimental effort to understand FP behavior. Experimental and computational findings were used in the development of a thermodynamic database containing 8 major FPs and their associated silicide phases. Finally, fuel compositions generated from depletion calculations were used to thermodynamically model the equilibrium phases of the fuel undergoing burnup.
Abstract Most ternary sulfides belonging to the MGaS 2 structure‐type have been known for many years and are well‐characterized. Surprisingly, there have been no reports of the NaGaS 2 composition, which contains Na, a monovalent cation slightly larger in size than Li, found in LiGaS 2 , a compound known for its non‐linear optical properties. Now it is demonstrated for the first time that the unique reversible water absorption in NaGaS 2 has resulted in its absence from previous reports owing to difficulties encountered when characterizing this compound by SC XRD. The layered structure of this compound coupled with uniquely easy migration of water molecules between the layers allows for ion exchange with 3d and 5f metal cations. Some cations, for example, Ni 2+ , facilitate exfoliation of the layers, providing a facile synthetic route to a new class of 2D chalcogenide materials and furthermore demonstrating that NaGaS 2 can readily uptake uranyl species from aqueous solutions.