Search NASA⌕ Search

Engineering topics

Koel, Bruce E.

Publications and source records attributed to Koel, Bruce E..

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Influence of Ordered Mesoporous Oxides in Plasma-Assisted Ammonia Synthesis

Widespread implementation of dielectric barrier discharge (DBD)-assisted NH 3 synthesis, a nascent technology operating under sustainable, ambient conditions, is hindered by low energy yields due to, in part, poor fundamental understanding. Porous oxides used to support metal nanoparticle catalysts have shown significant energy yield contributions for DBD-assisted NH 3 synthesis even without metal. Using an AC-powered, coaxial, single-stage reactor at 16 kV with equimolar (N 2 /H 2 ) feed, we measured NH 3 synthesis rates in the presence of different nonordered oxides, ordered SiO 2 structures (SBA-15 and MCM-41), and ordered Al-incorporated analogues (γ-Al 2 O 3 -coated with varying Al-loadings and Al-substitution, respectively: Al 2 O 3 -SBA-15 and Al-MCM-41). We systematically quantified NH 3 energy yield dependence on pore structures and material identities (i.e., ordered pores and Al incorporation) known to facilitate higher DBD-assisted NH 3 synthesis rates. SBA-15 displayed a higher steady-state energy yield than MCM-41, indicating that framework type is a crucial factor, with both ordered porous systems outperforming fumed SiO 2 . 10 wt % Al maximized in situ NH 3 uptake among the various Al loadings, exhibiting a higher steady-state energy yield and similar power to SBA-15. However, Al-MCM-41 had a similar steady-state energy yield and lower power than MCM-41, likely due to the extended γ-Al 2 O 3 surface that has a dielectric constant higher than that of SiO 2 . Both Al-incorporated analogues benefit from surface acid sites that can adsorb NH 3 in situ, resulting in higher overall NH 3 energy yields than that of their parent ordered SiO 2 . Al 2 O 3 -SBA-15 shielded more NH 3 than Al-MCM-41, likely due to a higher acid site density than the acid site identity. Furthermore, Al incorporation via γ-Al 2 O 3 coating more successfully improves the NH 3 energy yield; together with the high-performing ordered framework, these analogues are potential metal catalyst supports with promising energy yields for DBD-assisted synthesis of NH 3 and other chemicals.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Catalytic Consequences of Hierarchical Pore Architectures within MFI and FAU Zeolites for Polyethylene Conversion

The benefits of hierarchical zeolites for the conversion of bulky molecules like polymeric waste have been reported in the literature; however, the impact of mesopore sizes and connectivities on rates, product selectivities, and catalyst deactivation in the context of plastic upcycling has not been systematically probed. Here, in this study, we synthesized a suite of hierarchical MFI and FAU zeolites via desilication under varying conditions for metal-free polyethylene conversion reactions under batch and flow conditions (473–523 K). Polyethylene (solid) conversion rates (normalized by Bro̷nsted acid site density) were higher on hierarchical than parent microporous MFI regardless of mesopore connectivities, i.e., open or constricted, suggesting that the incorporation of mesopores facilitates diffusion of intermediate products to access medium-pore protons for successive scission events. Furthermore, higher branched:linear gaseous product ratios were produced on hierarchical than parent MFI, since mesopores allow for egress of bulkier molecules without undergoing further secondary events, e.g., isomerization back to linear alkanes/alkenes or beta scission. Solid conversion rates on hierarchical FAU synthesized via desilication with cetyltrimethylammonium bromide (CTABr), however, were not higher than parent FAU, likely because the presence of CTABr facilitates recrystallization of leached species to form composites (hierarchical FAU and ordered mesoporous materials) with more isolated mesopores. The stagnation in rates, despite increased mesopore volumes (>0.22 cm 3 g –1 ), highlights the importance of confinement effects provided by micropores for cleaving C–C bonds at modest reaction conditions. In situ 1 H MAS NMR performed on polyethylene with MFI zeolite show that PE isomerizes (and potentially deconstructs) at temperatures near 450 K, highlighting the role of Bro̷nsted acid sites in activating C–C bonds under mild reaction conditions. Catalyst recyclability studies showed that all catalysts undergo deactivation during plastic upcycling reactions, but to varying extents. Overall, hierarchical materials have better catalyst stability than parent materials, although the differences in stability between hierarchical and parent FAU are smaller than those for MFI. Taken together, these findings demonstrate how rates, selectivities, and catalyst deactivation from plastic upcycling reactions can be controlled via fine-tuning the identity and connectivity of mesopores.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Kinetic Modeling Analysis of Ar Addition to Atmospheric Pressure N 2 –H 2 Plasma for Plasma-Assisted Catalytic Synthesis of NH 3

Zero-dimensional kinetic modeling of atmospheric pressure Ar–N 2 –H 2 nonthermal plasma was carried out to gain mechanistic insights into plasma-assisted catalytic synthesis of ammonia. Ar dilution is a common technique for tailoring plasma discharge properties and has been shown to enhance NH 3 formation when added to N 2 –H 2 plasma. The kinetic model was developed for a coaxial dielectric barrier discharge quartz wool-packed bed reactor operating at near room temperature using a kHz-frequency plasma source. With 30% Ar mixed in a 1:1 N 2 –H 2 plasma at 760 Torr, we find that NH 3 production is dominated by Eley–Rideal (E-R) surface reactions, which heavily involve surface NH x species derived from N and H radicals in the gas phase, while the influence of excited N 2 molecules is negligible. This is contrary to the commonly proposed mechanism that excited N 2 molecules created by Penning excitation of N 2 by Ar(4s) and Ar(4p) play a significant role in assisting NH 3 formation. Our model shows that the enhanced NH 3 formation upon Ar dilution is unlikely due to the interactions between Ar and H species, as excited Ar atoms have a weak effect on H radical formation through H 2 dissociation compared to electrons. We find that excited Ar atoms contribute to 28% of the N radical production in the gas phase via N 2 dissociation, while the rest are dominated by electron-impact dissociation. Furthermore, Ar species play a negligible role in the product NH 3 dissociation. N 2 conversion sensitivity analyses were carried out for electron number density (ne) and reduced electric field (E/N), and contributions from Ar to gas-phase N radical production were quantified. Finally, the model can provide guidance on potential reasons for observing enhanced NH 3 formation upon Ar dilution in N 2 –H 2 plasma beyond changes in the discharge characteristics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Investigation of W-SiC compositionally graded films as a divertor material

W-SiC composite material is a promising plasma-facing material candidate alternative to pure W due to the low neutron activation, low impurity radiation, and low tritium diffusivity of SiC while leveraging the high erosion resistance of the W armor. Additionally, W and SiC have high thermomechanical compatibility given their similar thermal expansion rates. The present study addresses the synthesis and performance of compositionally graded W-SiC films fabricated by pulsed-DC magnetron sputtering. Compositional gradients were characterized using transmission electron microscopy (TEM) and energy-dispersive X-ray spectroscopy (EDS), and crystallographic information was obtained using electron diffraction and X-ray diffraction (XRD). Samples were exposed to L-mode deuterium plasma discharges in the DIII-D tokamak using the Divertor Material Evaluation System (DiMES). Post-mortem characterizations were performed using scanning electron microscopy (SEM) and XRD. Electron diffraction and XRD showed that the compositionally graded W-SiC films were composed of polycrystalline W and amorphous SiC with amorphous W+SiC interlayers. No macroscopic delamination or microstructural changes were observed under mild exposure conditions. Here, this study serves as a preliminary examination of W-SiC compositionally graded composites as a potential candidate divertor material in future tokamak devices.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Ion concentration ratio measurements of ion beams generated by a commercial microwave electron cyclotron resonance plasma source

A commercially available electron cyclotron resonance (ECR) plasma source (GenII Plasma Source, tectra GmbH) is widely used for surface processing. This plasma source is compatible with ultrahigh vacuum systems, and its working pressure is relatively low, around 10 –6 –10 –4 Torr even without differential pumping. Here, we report ion flux concentration ratios for each ion species in an ion beam from this source, as measured by a mass/energy analyzer that is a combination of a quadrupole mass spectrometer, an electrostatic energy analyzer, and focusing ion optics. In this study, the examined beams were those arising from plasmas produced from feed gases of H 2 , D 2 , N 2 , O 2 , Ar, and dry air over a range of input power and working pressures. H 2 (D 2 ) plasmas are widely used for nuclear fusion applications and, hence, the ion concentration ratios of H + , H 2 + , and H 3 + reported here will be useful information for research that applies this plasma source to well-controlled plasma-material interaction studies. Ion energy distributions, stability of operation, and impurity concentrations were also assessed for each of the plasma species investigated.

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

Surface Chemistry and Reactions for Bimetallic Au Catalysis (Final Report)

Gold-based catalysts offer tremendous opportunities for developing new technologies for selective oxidation reactions that directly use gas-phase oxygen as a benign reagent and produce either no byproducts or water as the only byproduct. These processes are urgently needed and critical for achieving the sustainable production of chemicals. While recent studies demonstrate that the catalytic properties of gold can be significantly enhanced by addition of other metals, the development of these catalysts with sufficient performance for commercialization is hindered by a lack of fundamental understanding of how the catalytic properties of gold can be controlled and tailored. This project addressed this need by synergistically combining experimental and computational studies to establish fundamental composition-structure-activity relationships for gold-based catalysts for several industrially important reactions. Results from surface spectroscopy, atomic imaging and thermal desorption experiments were combined with molecular models and reaction mechanisms from quantum chemical calculations to link observable reaction rates to the structure and composition of surfaces at the molecular level. The results were used to develop improved catalyst formulations and identify optimized reaction conditions for gold-based catalysts. For broader impacts, the developed methodology was extended to other metallic catalysts, such as silver, platinum-molybdenum and nickel-tin, for improved catalytic efficiency and sustainable production of specialty and commodity chemicals.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Determination of the characteristic magnetic pre-sheath length at divertor surfaces using micro-engineered targets on DiMES at DIII-D

The magnetic pre-sheath (MPS) width, L MPS , is a critical parameter to define the sheath potential, which controls the ion trajectory of low-Z species (D, T, He, and C), as well as the prompt re-deposition of high-Z species. In this work, to determine L MPS , we fabricated micro-trenches (30×30×4 µm) via focused ion beam (FIB) milling on a silicon surface and exposed them to L-mode deuterium plasmas in DIII-D via the Divertor Material Evaluation System (DiMES) removable sample exposure probe. The areal distribution of impurity depositions, mainly consisting of carbon, was measured by energy-dispersive X-ray spectroscopy (EDS) to reveal the deuterium ion shadowing effect on the trench floors. The carbon deposition profiles showed that the erosion was maximized for the azimuthal direction of φ = -40° (referenced to the toroidal magnetic field direction) as well as the polar angle of θ = 80°. A Monte Carlo equation-of-motion model, based on a collisionless MPS, was used to calculate the azimuthal and polar deuterium ion angle distributions (IADs) for a range of L MPS = k × ρ i , where ρ i is the ion gyro radius and k = 0.5-4. Then, gross erosion profiles were calculated by a Monte Carlo micro-patterning and roughness (MPR) code for ion sputtering using as input the calculated azimuthal and polar IADs for each value of k . Good agreement with the experimental C deposition profiles was obtained for the case k = 2.5-3.5. This result is consistent with a previous kinetic modeling prediction of k ~ 3, as well as previous analytical investigations that predicted the L MPS to be several ion gyro radii. A validation of theoretical sheath models supports its applicability to ITER and pilot plant divertors to successfully predict plasma-materials interactions.

Erosion↗
DOE OSTI2022

NSTX-U theory, modeling and analysis results

Here, the mission of the low aspect ratio spherical tokamak NSTX-U is to advance the physics basis and technical solutions required for optimizing the configuration of next-step steady-state tokamak fusion devices. NSTX-U will ultimately operate at up to 2 MA of plasma current and 1 T toroidal field on axis for 5 s, and has available up to 15 MW of neutral beam injection power at different tangency radii and 6 MW of high harmonic fast wave heating. With these capabilities NSTX-U will develop the physics understanding and control tools to ramp-up and sustain high performance fully non-inductive plasmas with large bootstrap fraction and enhanced confinement enabled via the low aspect ratio, high beta configuration. With its unique capabilities, NSTX-U research also supports ITER and other critical fusion development needs. Super-Alfvénic ions in beam-heated NSTX-U plasmas access energetic particle (EP) parameter space that is relevant for both α-heated conventional and low aspect ratio burning plasmas. NSTX-U can also generate very large target heat fluxes to test conventional and innovative plasma exhaust and plasma facing component solutions. This paper summarizes recent analysis, theory and modelling progress to advance the tokamak physics basis in the areas of macrostability and 3D fields, EP stability and fast ion transport, thermal transport and pedestal structure, boundary and plasma material interaction, RF heating, scenario optimization and real-time control.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Surface Chemistry and Heterogeneous Processes in Solar-Driven Pyridine-Catalyzed CO 2 Reduction

The objective of our studies was to advance our fundamental understanding of the surface chemistry and heterogeneous processes that occur in solar-driven pyridine-catalyzed CO 2 reduction. Solar-driven CO 2 reduction to produce fuels offers tremendous promise but commercial deployment is impeded by the lack of suitable catalysts that simultaneously provide high efficiency and product selectivity. Pyridine (C 5 H 5 N) has been reported as an effective, selective co-catalyst in the conversion of CO 2 to methanol (CH 3 OH) in photoelectrochemical cells employing gallium phosphide (GaP) photocathodes. However, despite considerable electrochemical characterization and a large number of theoretical considerations, there are still many fundamental questions about the surface chemistry and heterogeneous processes that are involved in the conversion mechanism. Our research was aimed at investigating the role of the electrode surface and heterogeneous processes in this catalysis. Gaining this fundamental understanding of the origin of pyridine’s effectiveness is important to the continued optimization of solar-driven CO 2 reduction.

10 SYNTHETIC FUELS↗
DOE OSTI2022

Spectroscopic observation and structure-insensitivity of hydroxyls on gold

Here, the O–H stretching vibration of surface hydroxyls remained at 3691 cm –1 for gold structures ranging in size from clusters to nanoparticles, to non-flat bulk surfaces. In contrast, this vibration was not observed on flat gold surfaces. Therefore, this vibration can serve as an indicator of the roughness of the gold surface and associated functional properties, such as catalytic activity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

In Situ Identification of NNH and N 2 H 2 by Using Molecular-Beam Mass Spectrometry in Plasma-Assisted Catalysis for NH 3 Synthesis

In this work, ammonia synthesis at 533 K and atmospheric pressure was investigated in a coaxial dielectric barrier discharge (DBD) plasma reactor without packing and with porous γ-Al 2 O 3 , 5 wt % Ru/γ-Al 2 O 3 , or 5 wt % Co/γ-Al 2 O 3 catalyst particles. Gas-phase species were monitored in situ using an electron impact molecular-beam mass spectrometer (EI-MBMS). Gas-phase species NNH and N 2 H 2 were first identified under common conditions of plasma-assisted ammonia synthesis and were present at levels comparable to that of NH 3 in the plasma discharge. Concentrations of NNH, N 2 H 2 , and NH in a reactor packed with γ-Al 2 O 3 or other particles were lower than those observed in an empty reactor, while the concentration of NH 3 increased. These observations point to the importance of NNH and N 2 H 2 in plasma-assisted surface reactions in ammonia synthesis. Reaction pathways of direct adsorption of gas-phase NNH and N 2 H 2 on solid surfaces and subsequent reactions were proposed. This study demonstrated that in situ identification of gas-phase species via EI-MBMS provides a powerful approach to study the kinetics of plasmaassisted catalysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Plasma-assisted catalysis for ammonia synthesis in a dielectric barrier discharge reactor: key surface reaction steps and potential causes of low energy yield

Ammonia synthesis experiments were carried out in a coaxial dielectric barrier discharge (DBD) reactor packed with several different supports and metal catalysts. There was a marked increase in the reaction rate, over that obtained in an empty DBD plasma reactor, upon introduction of a packed bed of γ-Al 2 O 3 , Ru/γ-Al 2 O 3 , or SiO 2 particles. The difference in the reaction rates over γ-Al 2 O 3 and Ru/γ-Al 2 O 3 was minimal. Complementary zero-dimensional plasma kinetic model analysis was also performed using inputs from experimental data. This kinetic analysis allowed for gas phase reactions, Eley–Rideal (E–R) reactions, and direct adsorption of radical species on the γ-Al 2 O 3 surface. On the metal surface, dissociative adsorption of N 2 and H 2 , and Langmuir–Hinshelwood reactions were also included. This analysis revealed that, under the conditions of our experiments, ammonia synthesis proceeds principally by the formation of reactive radicals in the gas phase, which then adsorb and participate in E–R reactions on both the metal and support material surfaces. Furthermore, this finding illustrates a challenge for substantially increasing the energy yield for plasma-assisted ammonia synthesis in typical DBD reactors containing packed catalyst beads.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Increasing Iridium Oxide Activity for the Oxygen Evolution Reaction with Hafnium Modification

Synthesis and implementation of highly active, stable, and affordable electrocatalysts for the oxygen evolution reaction (OER) is a major challenge in developing energy efficient and economically viable energy conversion devices such as electrolyzers, rechargeable metal-air batteries, and regenerative fuel cells. The current benchmark electrocatalyst for OER is based on iridium oxide (IrO x ) due to its superior performance and excellent stability. However, large scale applications using IrO x are impractical due to its low abundance and high cost. In this work, we report a highly active hafnium-modified iridium oxide (IrHf x O y ) electrocatalyst for OER. The IrHf x O y electrocatalyst demonstrated ten times higher activity in alkaline conditions (pH = 11) and four times higher activity in acid conditions (pH = 1) than a IrO x electrocatalyst. The highest intrinsic mass activity of the IrHf x O y catalyst in acid conditions was calculated as 6950 A gIrO x -1 at an overpotential (η) of 0.3 V. Combined studies utilizing operando surface enhanced Raman spectroscopy (SERS) and DFT calculations revealed that the active sites for OER are the Ir-O species for both IrO x and IrHf x O y catalysts. The presence of Hf sites leads to more negative charge states on nearby O sites, and shortening the bond lengths of Ir-O, and lowering free energies for OER intermediates to accelerate the OER process.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Controlled Dy-doping to nickel-rich cathode materials in high temperature aerosol synthesis

Layered nickel-rich materials are promising next-generation cathode materials for lithium ion batteries due to their high capacity and low cost. However, the poor thermal stability and longtime cycling performance hinders the commercial applications of high nickel materials. Doping with heteroatoms has been an effective approach for improving electrochemical performance of cathode materials. Controlling doping concentration and geometrical distribution is desired for optimal electrochemical performance, but it is challenging in traditional co-precipitation methods. In this work, controlled dysprosium (Dy) doping to NCM811 was studied in an aerosol synthesis method by controlling the precursor concentrations and heating parameters. The obtained materials were characterized by SEM, XRD, and XPS, and their electrochemical properties and thermal stability were evaluated. By controlling the doping concentration (1.5%), Dy-doped NCM811 was improved simultaneously in long-term cycling and high-rate performance. Here, the thermal-chemical stability of the Dy-doped cathode materials was examined in a microflow reactor with a mass spectrometer. The results showed that Dy-doping shifted the O 2 onset temperature to a higher temperature and reduced O 2 release by 80%, thus dramatically increasing the thermal-chemical stability and improving the fire safety of cathode materials. Since high temperature aerosol synthesis is a low-cost and scalable method, the findings in this work have broad implications for commercial synthesis of novel materials with controlled doping modification to achieve high electrochemical performance and safety in lithium ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2020

Acetic Acid Adsorption and Reactions on Ni(110)

Acetic acid adsorption and reactions at multiple surface coverage values on Ni(110) were studied with temperature-programmed desorption (TPD) and infrared reflection absorption spectroscopy (IRAS) at 90–500 K. The experimental measurements were interpreted with density functional theory (DFT) calculations that provided information on adsorbate geometries, energies, and vibrational modes. Below the monolayer saturation coverage of 0.36 ML at 90 K, acetic acid adsorbs mostly molecularly. Above this coverage, a physisorbed layer is formed with dimers and catemers, without detectable monomers. Dimers and catemers desorb as molecular acetic acid at 157 and 172 K, respectively. Between 90 and 200 K, the O–H bond in acetic acid breaks to form bridge-bonded bidentate acetate that becomes the dominant surface species. Desorption-limited hydrogen evolution is observed at 265 K. However, even after the acetate formation, acetic acid desorbs molecularly at 200–300 K due to recombination. Minor surface species observed at 200 K, acetyls or acetates with a carbonyl group, decompose below 350 K and generate adsorbed carbon monoxide. At 350 K, the surface likely undergoes restructuring, the extent of which increases with acetic acid coverage. The initial dominant bridge-bonded bidentate acetate species formed below 200 K remain on the surface, but they now mostly adsorb on the restructured sites. Here, the acetates and all other remaining hydrocarbon species decompose simultaneously at 425 K in a narrow temperature range with concurrent evolution of hydrogen, carbon monoxide, and carbon dioxide. Above 425 K, only carbon remains on the surface.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗