Engineering topics

Koenig, D. G.

Publications and source records attributed to Koenig, D. G..

At least 19 records

NASA NTRS1984

V/STOL wind-tunnel testing

Factors influencing effective program planning for V/STOL wind-tunnel testing are discussed. The planning sequence itself, which includes a short checklist of considerations that could enhance the value of the tests, is also described. Each of the considerations, choice of wind tunnel, type of model installation, model development and test operations, is discussed, and examples of appropriate past and current V/STOL test programs are provided. A short survey of the moderate to large subsonic wind tunnels is followed by a review of several model installations, from two-dimensional to large-scale models of complete aircraft configurations. Model sizing, power simulation, and planning are treated, including three areas is test operations: data-acquisition systems, acoustic measurements in wind tunnels, and flow surveying.

Koenig, D. G.↗

NASA NTRS1983

Large-scale wind-tunnel investigation of a close-coupled canard-delta-wing fighter model through high angles of attack

Data obtained through very high angles of attack from a large-scale, subsonic wind-tunnel test of a close-coupled canard-delta-wing fighter model are analyzed. The canard delays wing leading-edge vortex breakdown, even for angles of attack at which the canard is completely stalled. A vortex-lattice method was applied which gave good predictions of lift and pitching moment up to an angle of attack of about 20 deg, where vortex-breakdown effects on performance become significant. Pitch-control inputs generally retain full effectiveness up to the angle of attack of maximum lift, beyond which, effectiveness drops off rapidly. A high-angle-of-attack prediction method gives good estimates of lift and drag for the completely stalled aircraft. Roll asymmetry observed at zero sideslip is apparently caused by an asymmetry in the model support structure.

Stoll, F.↗

NASA NTRS1981

Application of thrusting ejectors to tactical aircraft having vertical lift and short-field capability

The status of ejector development in terms of application to V/STOL aircraft is reported in three categories: aircraft systems and ejector concepts; ejector performance including prediction techniques and experimental data base available; and, integration of the ejector with complete aircraft configurations. Available prediction techniques are reviewed and performance of three ejector designs with vertical lift capability is summarized. Applications of the 'fuselage' and 'short diffuser' ejectors to fighter aircraft are related to current and planned research programs. Recommendations are listed for effort needed to evaluate installed performance.

Koenig, D. G.↗

NASA NTRS1980

Large scale model tests of a new technology V/STOL concept

An ejector design concept for V/STOL aircraft, featuring a double-delta configuration with two large chordwise ejector slots adjacent to the fuselage side and a tailplane or canard for longitudinal control is examined. Large scale model tests of the concept have shown that ejector systems are capable of significant thrust augmentation at realistic supply pressures and temperatures, so that power plant size and weight can be reduced accordingly. A thrust augmentation of at least 1.75 can be achieved for the isolated ejector, not making allowance for duct and nozzle losses. Substantial reductions in velocity, temperature and noise of the lifting jet are assured due to mixing within the ejector - this lessens the severity of ground erosion and the thrust loss associated with reingestion. Consideration is also given to the effect of ground proximity, longitudinal aerodynamic characteristics, transition performance, and lateral stability.

Whittley, D. C.↗

NASA NTRS1979

Workshop on Thrust Augmenting Ejectors

The state of the art of ejector technology is assessed and the desired direction of future studies in all aspects of ejector thrust augmenting systems is deliniated.

Lopez, A. E.↗

NASA NTRS1979

NASA overview

The history of NASA efforts at Ames Research Center in researching the performance and application of thrusting augmentors is reviewed. Current objectives include: (1) parametric description of thrust augmentor application to STOL and V/STOL; (2) the use of theoretical and empirical data; (3) aircraft-augmentor integration; and (4) key design considerations for STOL transport and V/STOL fighter aircraft. Test facilities are described and ejector development and performance are assessed.

Koenig, D. G.↗

NASA NTRS1979

Wind-tunnel investigation of the thrust augmentor performance of a large-scale swept wing model

Tests were made in the Ames 40- by 80-foot wind tunnel to determine the forward speed effects on wing-mounted thrust augmentors. The large-scale model was powered by the compressor output of J-85 driven viper compressors. The flap settings used were 15 deg and 30 deg with 0 deg, 15 deg, and 30 deg aileron settings. The maximum duct pressure, and wind tunnel dynamic pressure were 66 cmHg (26 in Hg) and 1190 N/sq m (25 lb/sq ft), respectively. All tests were made at zero sideslip. Test results are presented without analysis.

Koenig, D. G.↗

NASA NTRS1977

Large-scale V/STOL testing

Several facets of large-scale testing of V/STOL aircraft configurations are discussed with particular emphasis on test experience in the Ames 40- by 80-Foot Wind Tunnel. Examples of powered-lift test programs are presented in order to illustrate tradeoffs confronting the planner of V/STOL test programs. Large-scale V/STOL wind-tunnel testing can sometimes compete with small-scale testing in the effort required (overall test time) and program costs because of the possibility of conducting a number of different tests with a single large-scale model where several small-scale models would be required. The benefits of both high- or full-scale Reynolds numbers, more detailed configuration simulation, and number and type of onboard measurements are studied.

Koenig, D. G.↗

NASA NTRS1977

Large-scale V/STOL testing

Several facets of large-scale testing of V/STOL aircraft configurations are discussed with particular emphasis on test experience in the Ames 40- by 80-foot wind tunnel. Examples of powered-lift test programs are presented in order to illustrate tradeoffs confronting the planner of V/STOL test programs. It is indicated that large-scale V/STOL wind-tunnel testing can sometimes compete with small-scale testing in the effort required (overall test time) and program costs because of the possibility of conducting a number of different tests with a single large-scale model where several small-scale models would be required. The benefits of both high- and full-scale Reynolds numbers, more detailed configuration simulation, and number and type of onboard measurements increase rapidly with scale. Planning must be more detailed at large scale in order to balance the trade-offs between the increased costs, as number of measurements and model configuration variables increase and the benefits of larger amounts of information coming out of one test.

Koenig, D. G.↗

NASA NTRS1975

Wind tunnel investigation of a large-scale upper surface blown-flap model having four engines

Investigations were conducted in the Ames 40- by 80-Foot Wind Tunnel to determine the aerodynamic characteristics of a large-scale subsonic jet transport model with an upper surface blown flap system. The model had a 25 deg swept wing of aspect ratio 7.28 and four turbofan engines. The lift of the flap system was augmented by turning the turbofan exhaust over the Coanda surface. Results were obtained for several flap deflections with several wing leading-edge configurations at jet momentum coefficients from 0 to 4.0. Three-component longitudinal data are presented with four engines operating. In addition, longitudinal and lateral data are presented with an engine out. The maximum lift and stall angle of the four engine model were lower than those obtained with a two engine model that was previously investigated. The addition of the outboard nacelles had an adverse effect on these values. Efforts to improve these values were successful. A maximum lift of 8.8 at an angle-of-attack of 27 deg was obtained with a jet thrust coefficient of 2 for the landing flap configuration.

Aoyagi, K.↗

NASA NTRS1975

Maximum lift of upper surface blowing STOL aircraft with swept wings

In a recent large scale wind tunnel investigation of a 4 engine upper surface blowing configuration in the Ames 40- by 80-Foot Wind Tunnel, the large nacelles extending well above the wing upper surface had a sizable adverse effect on maximum lift. The presence of the nacelles produced high upwash angles between the nacelles and near the fuselage. The severity and alleviation of this problem is discussed with the use of calculated spanwise loadings. The combined effects of wing leading edge stall control, wing sweep, and nacelle cross section modification were considered in maximum lift improvement. Experimental results of these effects are presented.

Koenig, D. G.↗

NASA NTRS1974

Comparison of the acoustic characteristics of large-scale models of several propulsive-lift concepts

Wind-tunnel acoustic investigations were performed to determine the acoustic characteristics and the effect of forward speed on the over-the-wing externally blown jet flap (OTW), the under-the-wing externally blown jet flap (UTW), the internally blown jet flap (IBF), and the augmentor wing (AW). The data presented represent the basic noise generated by the powered-lift system without acoustic treatment, assuming all other noise sources, such as the turbofan compressor noise, have been suppressed. Under these conditions, when scaled to a 100,000-lb aircraft, the OTW concept exhibited the lowest perceived noise levels, because of dominant low-frequency noise and wing shielding of the high-frequency noise. The AW was the loudest configuration, because of dominant high-frequency noise created by the high jet velocities and small nozzle dimensions. All four configurations emitted noise 10 to 15 PNdB higher than the noise goal of 95 PNdB at 500 ft.

Falarski, M. D.↗

NASA NTRS1973

Acoustic characteristics of a large-scale augmentor wing model at forward speed

The augmentor wing concept is being studied as one means of attaining short takeoff and landing (STOL) performance in turbofan powered aircraft. Because of the stringent noise requirements for STOL operation, the acoustics of the augmentor wing are undergoing extensive research. The results of a wind tunnel investigation of a large-scale swept augmentor model at forward speed are presented. The augmentor was not acoustically treated, although the compressor supplying the high pressure primary air was treated to allow the measurement of only the augmentor noise. Installing the augmentor flap and shroud on the slot primary nozzle caused the acoustic dependence on jet velocity to change from eighth power to sixth power. Deflecting the augmentor at constant power increased the perceived noise level in the forward quadrant. The effect of airspeed was small. A small aft shift in perceived noise directivity was experienced with no significant change in sound power. Sealing the lower augmentor slot at a flap deflection of 70 deg reduced the perceived noise level in the aft quadrant. The seal prevented noise from propagating through the slot.

Falarski, M. D.↗

NASA NTRS1973

Wind tunnel investigation of a large-scale 25 deg swept-wing jet transport model with an external blowing triple-slotted flap

An investigation has been conducted to determine the aerodynamic characteristics of a large-scale subsonic jet transport model with an externally blown triple-slotted flap. The lift of the model was augmented by the turbofan engine exhaust impingement on the flap surface. The model had a 25 deg swept wing of aspect ratio 7.28 and four turbofan engines. The model was tested with two flap extents. One extended from 0.11 to 1.00 of the wing semispan, and the other extended from 0.11 to 0.75 of the wing semispan with a single-slotted aileron from 0.75 to 1.00 of the wing semispan. The results were obtained for several flap deflections with and without the horizontal tail at gross thrust coefficients from 0 to 4.0. Longitudinal and lateral data are presented with three and four engines operating.

Aoyagi, K.↗

NASA NTRS1973

Acoustic characteristics of a large-scale wind tunnel model of an upper-surface blown flap transport having two engines

The upper-surface blown (USB) flap as a powered-lift concept has evolved because of the potential acoustic shielding provided when turbofan engines are installed on a wing upper surface. The results from a wind tunnel investigation of a large-scale USB model powered by two JT15D-1 turbofan engines are-presented. The effects of coanda flap extent and deflection, forward speed, and exhaust nozzle configuration were investigated. To determine the wing shielding the acoustics of a single engine nacelle removed from the model were also measured. Effective shielding occurred in the aft underwing quadrant. In the forward quadrant the shielding of the high frequency noise was counteracted by an increase in the lower frequency wing-exhaust interaction noise. The fuselage provided shielding of the opposite engine noise such that the difference between single and double engine operation was 1.5 PNdB under the wing. The effects of coanda flap deflection and extent, angle of attack, and forward speed were small. Forward speed reduced the perceived noise level (PNL) by reducing the wing-exhaust interaction noise.

Falarski, M. D.↗

NASA NTRS1973

Wind tunnel investigation of a large-scale upper surface blown-flap transport model having two engines

An investigation has been conducted to determine the aerodynamic characteristics of a large-scale subsonic jet transport model with an upper surface blowing flap system that would augment lift. The model had a 25 deg swept wing of aspect ratio 7.89 and two turbofan engines with the engine centerline located at 0.256 of the wing semispan. The lift of the flap system was augmented by turbofan exhaust impingement on the Coanda surface. Results were obtained for several flap deflections and engine nozzle configurations at jet momentum coefficients from 0 to 4.0. Three-component longitudinal data are presented with two engines operating. Limited longitudinal and lateral data are presented with an engine out. In addition, limited exhaust and flap pressure data are presented.

Aoyagi, K.↗

NASA NTRS1973

Aspects of investigating STOL noise using large-scale wind-tunnel models.

The applicability of the NASA Ames 40- by 80-foot wind tunnel for acoustic research on STOL concepts has been investigated. The acoustic characteristics of the wind-tunnel test section have been studied with calibrated acoustic sources. Acoustic characteristics of several large-scale STOL models have been studied in both the free-field and wind-tunnel acoustic environments. The results of these studies indicate that the acoustic characteristics of large-scale STOL models can be measured in the wind tunnel if the test section acoustic environment and model acoustic similitude are taken into consideration. The reverberant field of the test section must be determined with an acoustically similar noise source. A directional microphone, a phased array of microphones, and extrapolation of near-field data to far-field are some of the techniques being explored as possible solutions to the directivity loss in a reverberant field. The model sound pressure levels must be of sufficient magnitude to be distinguishible from the wind-tunnel background noise.

Falarski, M. D.↗

NASA NTRS1972

Longitudinal aerodynamic characteristics of a large scale model with a swept wing and augmented jet flap in ground effect

The investigation of the in-ground-effect, longitudinal aerodynamic characteristics of a large scale swept augmentor wing model is presented, using 40 x 80 ft wind tunnel. The investigation was conducted at three ground heights; h/c equals 2.01, 1.61, and 1.34. The induced effect of underwing nacelles, was studied with two powered nacelle configurations. One configuration used four JT-15D turbofans while the other used two J-85 turbojet engines. Two conical nozzles on each J-85 were used to deflect the thrust at angles from 0 to 120 deg. Tests were also performed without nacelles to allow comparison with previous data from ground effect.

Falarski, M. D.↗