Search NASA⌕ Search

Engineering topics

Koerner, Hilmar

Publications and source records attributed to Koerner, Hilmar.

10 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Thermal conductivity of 3D-printed block-copolymer-inspired structures

This study primarily focuses on examining the impact that geometric structure has on thermal conductivity of multi-phase constructs in different 3D-printed poly(lactic acid), PLA, samples. The investigated structures are inspired by morphologies formed by diblock copolymers: lamellae, hexagonally packed cylinders, and gyroid. This research also investigates how volume percentage and material combination influence the thermal conductivity of these structures. Further, the samples can be tailored to simulate various thermal management structures observed in practical applications, such as thermal interface materials in electronic devices. Thermal conductivity ratio is controlled using air, the least conductive material at 0.026 W/(m K), PLA at 0.136 W/(m K), and thermal paste at 5.11 W/(m K). Different models were tested against thermal conductivity measurements in order to capture the effect of material type (PLA-Air versus PLA-Thermal Paste), volume percentage, structure, and orientation. Simple, effective medium models were good predictions of thermal conductivity in lamellar structures, but it was necessary to develop models for conduction through cylindrical and gyroid structures. Finally, all results were normalized to find a universal model that is independent of structure and material. This approach provides a simple method to predict how to reduce or enhance transport properties and heat management capabilities of 3D printed objects.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Dynamics of Polymerization and Gelation in Epoxy Nanocomposites via X-ray Photon Correlation Spectroscopy

The details of the curing process of epoxy resins are notoriously difficult to ascertain, hampering polymer matrix composite manufacturing. Here, the curing of a series of six epoxy resins containing dilute spherical nanoparticles was investigated via X-ray photon correlation spectroscopy (XPCS). The resin formulation was varied to achieve a range of crosslink densities and topologies. Prior to gelation, the viscosities obtained from XPCS agreed with bulk rheology. A clear dynamic transition was detected in all samples, where the q-scaling changes from approximately q2 .2 to q 1 , indicating a transition from sub-diffusive to ballistic-like nanoparticle motion. For the samples with a high crosslink density, this change was abrupt and coincided with gelation, and there was no evidence of crosslink heterogeneity. Chain entanglement played a role in the transition for samples with lower crosslink density. Finally, this work reveals the potential of XPCS to deliver new quantitative insights into the curing process of thermosetting resins.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Tailorable Micelle Morphology in Self-Assembling Block Copolymer Gels for Templating Nanoporous Ceramics

The self-assembly of block copolymers offers opportunities for the facile organization and templating of inorganic nanomaterials. Here, we describe a morphology map for a poly(methyl methacrylate)-b-poly(n-butyl acrylate)-b-poly(methyl methacrylate) (PMMA-b-PnBA-b-PMMA) block copolymer/polycarbosilane system that allows for tunable control over nanoscale micelle geometry via manipulation of the preceramic polymer content. We produced gels with spherical, wormlike, and bicontinuous morphologies, which were processed to create silicon carbide-based ceramic structures with tunable nanoscale porosities. The role of the constituent polymers in influencing the structure and rheology of this system is discussed. The PMMA-b-PnBA-b-PMMA block copolymer/preceramic polymer system offers a number of advantages including: (i) commercial availability, (ii) rapid self-assembly kinetics, and (iii) successful conversion of the self-assembled nanostructure to ceramic via pyrolysis. Finally, this system may be useful for catalytic, structural, or thermal applications in both industrial and academic settings because of its ease of use and relatively inexpensive reagents.

36 MATERIALS SCIENCE↗
NASA NTRS2019

Laser Sintering of Thermoset Polyimide Composites

Selective Laser Sintering (SLS) is an additive manufacturing technique that builds 3D models layer by layer using a laser to selectively melt cross sections in powdered polymeric materials, following sequential slices of the CAD model. SLS generally uses thermoplastic polymeric powders, such as polyamides (i.e. Nylon), and the resultant 3D objects are often weaker in their strength compared to traditionally processed materials, due to the lack of polymer inter-chain connection in the z-direction. Our previous effort showed the challenges of printing a melt-processable RTM370 imide resin powder terminated with reactive 4-phenylethynylphthalic anhydride by LS, due to its inherently low viscosity of these oligomers. This paper presented the first successful 3D printing of high temperature carbon fiber filled thermoset polyimide composites, followed by post cure cycles to promote additional crosslinking for achieving higher temperature (Tg = 370 °C) capability. The processes to build tensile specimens and a component by LS, and the characterization of RTM370 imide resin by DSC and rheology as well as evaluation of the LS printed polyimide composite specimens by SEM and mechanical tests will be discussed.

Polyimide Composites↗
NASA NTRS2016

Challenges in Laser Sintering of Melt-Processable Thermoset Imide Resin

Polymer Laser Sintering (LS) is an additive manufacturing technique that builds 3D models layer by layer using a laser to selectively melt cross sections in powdered polymeric materials, following sequential slices of the CAD model. LS generally uses thermoplastic polymeric powders, such as polyamides (i.e. Nylon), and the resultant 3D objects are often weaker in their strength compared to traditionally processed materials, due to the lack of polymer inter-chain connection in the z-direction. The objective of this project is to investigate the possibility of printing a melt-processable RTM370 imide resin powder terminated with reactive phenylethynyl groups by LS, followed by a postcure in order to promote additional crosslinking to achieve higher temperature (250-300 C) capability. A preliminary study to build tensile specimens by LS and the corresponding DSC and rheology study of RTM370 during LS process is presented.

Additive Manufacturing↗
NASA NTRS2016

Challenges in Laser Sintering of Thermoset Imide Resin

Polymer Laser Sintering (LS) is an additive manufacturing technique that builds 3D models layer by layer using a laser to selectively melt cross sections in powdered polymeric materials, following sequential slices of the CAD model. LS generally uses thermoplastic polymeric powders, such as polyamides (i.e. Nylon), and the resultant 3D objects are often weaker in their strength compared to traditionally processed materials, due to the lack of polymer inter-chain connection in the z-direction. The objective of this project is to investigate the possibility of printing a melt-processable RTM370 imide resin powder terminated with reactive phenylethynyl groups by LS, followed by a postcure in order to promote additional crosslinking to achieve higher temperature (250-300 C) capability. A preliminary study to build tensile specimens by LS and the corresponding DSC and rheology study of RTM370 during LS process is presented.

Additive Manufacturing↗