Search NASA⌕ Search

Engineering topics

Kolasinski, Robert

Publications and source records attributed to Kolasinski, Robert.

18 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

In-situ ETEM study of plasma-facing tungsten nanofuzz oxidation at atmospheric pressure: Microstructure evolution and substrate-free oxidation kinetics

To enable sustainable carbon-free fusion energy, managing reactor structural material degradation during normal operation as well as accident scenarios is vital. Tungsten (W) plasma-facing materials (PFMs) are susceptible to aggressive high-temperature oxidation during air-ingress fusion reactor accidents, yet there's a lack of oxidation kinetic data for irradiated tungsten. Here, in this study, we utilize atmospheric environmental transmission electron microscopy (ETEM) to present the first kinetic data for substrate-free W nanofuzz oxidation at 400 ºC and 500 ºC in 1 bar dry air. Comparison with pristine bulk W during the early parabolic stage suggests an irradiationdecelerated oxidation for W nanofuzz. Our time-resolved in-situ characterization reveals a durable amorphous surface oxide, likely promoted by high-flux He + irradiation-induced surface defects, serving as an effective passivating layer that impedes nanofuzz oxidation onset. This surface oxide layer also interfaces well with newly formed orthorhombic WO 3 , facilitated by stress relief through He bubble shrinkage, providing lasting passivating protection throughout the nanofuzz parabolic oxidation. This new finding challenges conventional notions of irradiation's negative impact on metal oxidation, and calls for advanced characterization to enhance our understanding of fusion energy materials degradation, informed by further accident modeling.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Effect of He seeding on hydrogen isotope permeation in tungsten by H-D mixed plasma exposure

Hydrogen (H) and deuterium (D) permeation fluxes for tungsten (W) by H-D mixed plasma were studied to clarify the hydrogen isotope effect on permeation by a newly designed plasma driven permeation (PDP) device at Shizuoka University. A mixed H-D plasma was produced by introducing H and D gasses with various ratios. The atomic ratio and permeation flux in the plasma were measured during the experiments. It was found that the H:D atomic ratio in the plasma was almost proportional to the introduced H:D gas ratio. When single species of H or D was irradiated, the H permeation rate showed approximately 1.6 times as high as that of D. Under H-D mixed plasma irradiation, the highest HD permeation rate was observed when the atomic ratio of H:D in the plasma was 50:50. In addition, the effect of He seeding on H-D mixed plasma driven permeation behavior was also evaluated. The recycling of hydrogen isotopes on the upstream side was enhanced due to the formation of He bubbles near the surface, which would prevent the dissolution of hydrogen isotopes into bulk W and enhance the reflection process during plasma exposure. H and D permeation fluxes were clearly reduced by seeding He in H-D mixed plasma. At lower temperature (~723 K), the ratio of steady permeation fluxes of H and D was about 75 : 25, confirming the high permeation flux of H . These results have demonstrated a significant hydrogen isotope effect, even if He was seeded or not. As the temperature increased, H and D permeation fluxes approached unity at 923 K. Therefore,this indicates that the hydrogen isotope effect was determined by the combination of recycling / reflection at or beneath the surface, which will be controlled by the temperature during plasma exposure.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

New experimental approach to understanding the chemical reactivity of oxide surfaces

Metal oxides have been an attractive option for a range of applications, including hydrogen sensors, microelectronics, and catalysis, due to their reactivity and tunability. The properties of metal oxides can vary greatly on their precise surface structure; however, few surface science techniques can achieve atomistic-level determinations of surface structure, and fewer yet can do so for insulator surfaces. Low energy ion beam analysis offers a potential insulator-compatible solution to characterizing the surface structure of metal oxides. As a feasibility study, we apply low energy ion beam analysis to investigate the surface structure of a magnetite single crystal, Fe 3 O 4 (100). We obtain multi-angle maps using both forward-scattering low energy ion scattering (LEIS) and backscattering impact-collision ion scattering spectroscopy (ICISS). Both sets of experimental maps have intensity patterns that reflect the symmetries of the Fe 3 O 4 (100) surface structure. However, analytical interpretation of these intensity patterns to extract details of the surface structure is significantly more complex than previous LEIS and ICISS structural studies of one-component metal crystals, which had far more symmetries to exploit. To gain further insight into the surface structure, we model our experimental measurements with ion-trajectory tracing simulations using molecular dynamics. Our simulations provide a qualitative indication that our experimental measurements agree better with a subsurface cation vacancy model than a distorted bulk model.

36 MATERIALS SCIENCE↗