Engineering topics

Kollberg, Erik L.

Publications and source records attributed to Kollberg, Erik L..

5 records

NASA NTRS1995

Conversion gain and noise of niobium superconducting hot-electron-mixers

A study has been done of microwave mixing at 20 GHz using the nonlinear (power dependent) resistance of thin niobium strips in the resistive state. Our experiments give evidence that electron-heating is the main cause of the nonlinear phenomenon. Also a detailed phenomenological theory for the determination of conversion properties is presented. This theory is capable of predicting the frequency-conversion loss rather accurately for arbitrary bias by examining the I-V-characteristic. Knowing the electron temperature relaxation time, and using parameters derived from the I-V-characteristic also allows us to predict the -3 dB IF bandwidth. Experimental results are in excellent agreement with the theoretical predictions. The requirements on the mode of operation and on the film parameters for minimizing the conversion loss (and even achieving conversion gain) are discussed in some detail. Our measurements demonstrate an intrinsic conversion loss as low as 1 dB. The maximum IF frequency defined for -3 dB drop in conversion gain, is about 80 MHz. Noise measurements indicate a device output noise temperature of about 50 K and SSB mixer noise temperature below 250 K. This type of mixer is considered very promising for use in low-noise heterodyne receivers at THz frequencies.

CONVERSION GAIN↗

NASA NTRS1992

Current saturation in submillimeter wave varactors

In semiconductor devices the speed of electrons cannot exceed certain limits. This phenomenon will affect varactor multipliers as well as other high frequency devices where the RF current through the active part of the device is primarily displacement current. Hence, 'saturation' of the varactor output power is expected at some point. This phenomenon is discussed in some detail and shown to severely deteriorate the multiplier performance at higher frequencies. Single barrier varactors should have an advantage over GaAs Schottky diode varactors because they can be fabricated on InAs and stacked in a series array, allowing for lower current densities and higher power handling.

Kollberg, Erik L.↗

NASA NTRS1992

Progress on single barrier varactors for submillimeter wave power generation

Theoretical work on Single Barrier Varactor (SBV) diodes, indicate that the efficiency for a multiplier has a maximum for a considerably smaller capacitance variation than previously thought. The theoretical calculations are performed, both with a simple theoretical model and a complete computer simulation using the method of harmonic balance. Modeling of the SBV is carried out in two steps. First, the semiconductor transport equations are solved simultaneously using a finite difference scheme in one dimension. Secondly, the calculated I-V, and C-V characteristics are input to a multiplier simulator which calculates the optimum impedances, and output powers at the frequencies of interest. Multiple barrier varactors can also be modeled in this way. Several examples on how to design the semiconductor layers to obtain certain characteristics are given. The calculated conversion efficiencies of the modeled structures, in a multiplier circuit, are also presented. Computer simulations for a case study of a 750 GHz multiplier show that InAs diodes perform favorably compared to GaAs diodes. InAs and InGaAs SBV diodes have been fabricated and their current vs. voltage characteristics are presented. In the InAs diode, was the large bandgap semiconductor AlSb used as barrier. The InGaAs diode was grown lattice matched to an InP substrate with InAlAs as a barrier material. The current density is greatly reduced for these two material combinations, compared to that of GaAs/AlGaAs SBV diodes. GaAs based diodes can be biased to higher voltages than InAs diodes.

Nilsen, Svein M.↗

NASA NTRS1989

The tapered slot antenna - A new integrated element for millimeter-wave applications

Tapered slot antennas (TSAs) with a number of potential applications as single elements and focal-plane arrays are discussed. TSAs are fabricated with photolithographic techniques and integrated in either hybrid or MMIC circuits with receiver or transmitter components. They offer considerably narrower beams than other integrated antenna elements and have high aperture efficiency and packing density as array elements. Both the circuit and radiation properties of TSAs are reviewed. Topics covered include: antenna beamwidth, directivity, and gain of single-element TSAs; their beam shape and the effect of different taper shapes; and the input impedance and the effects of using thick dielectrics. These characteristics are also given for TSA arrays, as are the circuit properties of the array elements. Different array structures and their applications are also described.

Yngvesson, K. Sigfrid↗

NASA NTRS1986

A new integrated slot element feed array for multibeam systems

A feed array consisting of constant width slot antennas (CWSA), fed from a block containing fin-line transitions, has been developed. The array has a two-dimensional configuration, with five elements each on five parallel substrates. Beamwidths are compatible with use in f/D = 1.0 multibeam systems, with optimum taper. Array element spacings are close to a factor of two smaller than for other typical arrays, and spillover efficiency is about 65 percent.

Yngvesson, K. Sigfrid↗