Search NASA⌕ Search

Engineering topics

Komarasamy, Mageshwari

Publications and source records attributed to Komarasamy, Mageshwari.

At least 19 records

Microstructural Engineering of Cu-Rich Nanoprecipitate formation in NiCoFeCrCu0.12 High-Entropy Alloy via Severe Plastic Deformation for Enhanced Irradiation Tolerance

This study demonstrates a defect-engineering approach for controlling Cu-rich precipitates in FeNiCrCoCu0.2 high-entropy alloys (Cu-HEAs), delivering a novel pathway for next-generation nuclear reactor materials with superior irradiation resistance. This work establishes that severe plastic deformation (SPD) processing via Shear Assisted Processing and Extrusion (ShAPE) and Friction Stir Layer Deposition (FSLD) creates dense dislocation networks and subgrain boundaries that fundamentally alter precipitation behavior under identical thermal treatments. Atom probe tomography (APT) indicates that SPD produces a metastable, atomically homogeneous solid solution that, upon moderate heat treatment (500°C/10 hour), develops remarkedly stronger Cu clustering than the as-cast counterpart. High-temperature exposure (800°C/100 h) produces near-pure Cu precipitates (~90 at% Cu) with significantly enhanced defect-sink efficacy in SPD-processed alloys: precipitate sizes of 50-60 nm and number densities of 2.7-3.8 × 10¹7 m?³, compared to 89 nm and 0.44 × 10¹7 m?³ in as-cast materials. Collectively, the findings establish defect-mediated precipitation control as a scalable, high-impact route to tailor sink density and distribution in HEAs, enabling microstructures optimized for irradiation tolerance and mechanical robustness in nuclear reactor environments.

Meher, Subhashish↗

Friction-based recycling: an evaluation of friction extrusion for fabricating Ti-6Al-4 V wire fabricated from machining chip feedstock

Abstract Titanium and its alloys are used in aviation and automobile industries due to their remarkable strength to weight ratio, but machining loss commonly is high with ~ 80 wt% of the material being converted to scrap. Recycling post-consumer Ti scrap directly into solid bulk products is a potential solution for repurposing valuable material. Further, eliminating fresh Ti sponge during recycling might lead to lower energy and greenhouse gas emissions. In this study, a solid-phase process known as friction extrusion was utilized to recycle Ti-6Al-4 V machining chips into solid wires which could be used as feedstock in additive manufacturing. The friction consolidation technique was first used to convert chips with varying degrees of oxygen content into solid billets for its use as feedstock material in subsequent friction extrusion. The extrudates were fabricated above the beta transition temperature, which was achieved by selecting the rotation rate and feed rate, to process the billets near 1000 °C using a tungsten-lanthana extrusion die. This work presents the first occurrence of friction extruded titanium alloy wires. The effect of friction extrusion on microstructural features, tensile properties, and texture are reported. Overall, the friction extrusion method is capable of directly recycling Ti-6Al-4 V scrap into extruded wire.

Friction Extrusion↗

Preliminary Characterization and Evaluation on ShAPE Manufactured 316H and ODS Steels

This study provides the first- of- a- kind results of direct tube formation through shear assisted processing and extrusion (ShAPE) for oxide dispersion strengthened (ODS) steel material; previously only bar was successfully made. The Advanced Materials and Manufacturing Technology (AMMT) program develops cross-cutting technologies in support of a broad range of nuclear reactor technologies and maintains U.S. leadership in materials and manufacturing technologies for nuclear energy applications. The overarching vision of AMMT is to accelerate the development, qualification, demonstration, and deployment of advanced materials and manufacturing technologies to enable reliable and economical nuclear energy. Solid-state advanced manufacturing techniques can overcome some of the challenges in liquid-based additive manufacturing processes and should therefore be considered in material design and manufacturing as well. The work presented in this report forms part of a study on solid-state additive manufacturing techniques of 316 stainless steels and ODS steel components and supports the vision and goals of the AMMT program relevant to accelerate the development and deployment of advanced manufacturing processes. Achieving this can provide a safety improvement through larger safety margins, economic benefit for higher efficiency during operation, and a cost reduction through more effective manufacturing processes and less waste.

36 MATERIALS SCIENCE↗

Recycling of Titanium Scrap by Shear Assisted Processing and Extrusion (ShAPE)

Titanium and its alloys are used in the aviation and automobile industries due to their remarkable strength to weight ratio, but, commonly, machining loss is high with ~90 wt.% of the material being converted to scrap. Recycling post-consumer Ti scrap directly into solid bulk products is a potential solution for repurposing valuable material. Further, reducing or even eliminating fresh Ti sponge during recycling might lead to lower energy and greenhouse gas emissions. In this study, a solid-phase process known as friction extrusion was utilized to recycle Ti-6Al-4V machining chips into solid wires which could be used as feedstock in additive manufacturing. The friction consolidation technique was first used to convert chips with varying degrees of oxygen content into solid billets for its use as feedstock material in subsequent friction extrusion. The extrudates were fabricated above the beta transition temperature, which was achieved by selecting rotation rate and feed rate, to process the billets near 1000°C using a tungsten-lanthana extrusion die. This work presents the first occurrence of friction extruded titanium alloy wires. The effect of friction extrusion on microstructural features, tensile properties, and texture are reported. Overall, the friction extrusion method is capable of recycling Ti-6Al-4V scrap directly into extruded wire.

36 MATERIALS SCIENCE↗

Shear-assisted extrusion assemblies and methods

Shear-assisted extrusion assemblies are provided. The assemblies can include a billet containing assembly containing a billet comprising a billet outer material and a billet inner material in at least one cross-section; a tool operably engaged with the billet; an extrudate receiving channel configured to receive extrudate from the tool, wherein the extrudate comprises extruded outer material and extruded inner material in at least one cross-section, the extruded outer material being the same material as the billet outer material, and the extruded inner material being the same as the billet inner material. Methods for producing multi-material shear-assisted extrudate are also provided.

Komarasamy, Mageshwari↗

Co-Extrusion of Dissimilar Aluminum Alloys via Shear-Assisted Processing and Extrusion

Bimetallic tubes are used when a component requires more than one performance requirement, for instance, strength/creep resistance and oxidation/corrosion resistance. Shear-assisted processing and extrusion (ShAPE) can be used to fabricate extrudates that are comparable or superior in performance relative to conventionally manufactured extrudates. For the first time, ShAPE has been successfully employed in producing bimetallic Al tubing consisting of 6061 and 7075 Al alloys. Both light and electron microscopy techniques were used to investigate the integrity of the tubes, especially the interface between the core and cladding of the bimetallic tubes. Void-free bimetallic tubes were produced using ShAPE. Quantification of tube integrity was carried out with tensile testing under as-extruded and post-aged conditions. All the bimetallic tubes in the as-extruded samples exhibited uniform elongation above 5% with good tensile strength. Key insights such as material flow during bimetallic tube extrusion were obtained from the characterization of remnant billet and simulation results from a smoothed particle hydrodynamics model.

36 MATERIALS SCIENCE↗

Feasibility Evaluation of a Solid Phase Scalable HEA Cladding Manufacturing Route

First of a kind development result on two low-energy solid-phase processes applied on an irradiation-resistant alloy, NiCoFeCrCu 0.12 , are achieved and demonstrate moderate feasibility of successful tube fabrication using shear assisted processing and extrusion (ShAPE™) and friction stir layer deposition as a bulk manufacturing process. The scope of the work is performed in four phases: 1) direct tube manufacturing of the irradiation-resistant high-entropy alloy (HEA) composite with increased strength, 2) co-shear lining manufacturing process for the increased strength and corrosion-resistant, irradiation-tolerant HEAs, 3) ShAPE of the radially gradient corrosion resistance alloy, and 4) alloy development and fabrication enabled through friction stir additive manufacturing processes among others. This report describes the development activities from April to December 2023 to manufacture a direct customizable thin-walled tubular product from irradiation-tolerant composite high-entropy alloys (C-HEAs) while the overall project is continuing in 2024.

36 MATERIALS SCIENCE↗

Preliminary HEA Solid Phase Processing Development Report

The development of high temperature fuel cladding materials to withstand a variety of extreme environments have received much attention. Several potential materials systems that have been identified for the fuel systems and core structural materials application in advanced reactor systems are ferritic/martensitic steel (e.g., HT9), austenitic stainless steels (e.g., 316 LN), oxide-dispersion strengthened steels (e.g., 12 YWT), Ni-based alloys and ceramic-based composites depending on the type of the reactors. Though these material systems have promising properties conducive for radiation-resistant performance, they suffer beyond the design-limit from one or more damage processes such as void swelling, radiation embrittlement, phase instability, corrosion, and limited creep life.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

High-speed friction stir butt welding of 25.4 mm thick 7175-T79 aluminum alloy

This presents the first experimental demonstration of friction stir butt welding of 25.4 mm thick high-strength, precipitate-strengthened 7XXX aluminum alloy at a welding speed above 500 mm/min and penetration depth greater than 10 mm. Tool pin threads that terminate away from the shoulder region, helped mitigate nearby stress concentration during tool traversing, enabling a higher welding speed while avoiding pin fracture near shoulder. Two kinds of welds—one-sided with full penetration of the plate thickness and double-sided with partial penetration of the plate thickness—were conducted. Significant grain refinement (grain size 1.3 ± 0.8 µm) was evident at the junction of double-sided friction stir welding (FSW) compared to other regions of weld-nugget or base material. Cross-weld tensile testing with digital image correlation revealed high local strains at the junction of double-sided FSW before macro-yield. This strain concentration impeded the typical early necking on advancing/retreating sides of FSW joints, improving the yield strength of as-welded double-sided FSW by 20–24% over slow- to medium-speed one-sided FSW. In conclusion, the joint efficiency of as-welded, double-sided high-speed FSW was about 76% with respect to the base material’s ultimate tensile strength.

36 MATERIALS SCIENCE↗

Evaluation of printability methodologies and feasibility to down select LBPF steel and other materials for nuclear applications

In this work, new research is underway to produce alloys beyond well-known alloys with modified compositions that are better suited to be produced with additive manufacturing. These alloys can only possess improved radiation tolerance but also improved high temperature strength, creep resistance while also using elements that reduce the amount of activation after irradiation. This work package supports the vision and goals of the Advanced Materials and Manufacturing Technology (AMMT) program relevant to accelerate the development and deployment of advanced manufacturing processes. This work focuses on evaluating the methodology for designing alloys best suited for AM processes based on “printability”, literature research to evaluate and down select steel alloy systems. In this work, microstructural characterization and testing activities have been performed on certain steel alloys to support the efforts from collaborating laboratories during the evaluation and printing of the test articles. The final recommendation will be performed by all four participating laboratories.

316L↗

Extrusion processes for forming extrusions of a desired composition from a feedstock

Devices and methods for performing shear-assisted extrusion processes for forming extrusions of a desired composition from a feedstock material are provided. The processes can use a device having a scroll face having an inner diameter portion bounded by an outer diameter portion, and a member extending from the inner diameter portion beyond a surface of the outer diameter portion.Extrusion feedstocks and extrusion processes are provided for forming extrusions of a desired composition from a feedstock. The processes can include providing a feedstock having at least two different materials and engaging the materials with one another within a feedstock container.Methods for preparing metal sheets are provided that can include preparing a metal tube via shear assisted processing and extrusion; opening the metal tube to form a sheet having a first thickness; and rolling the sheet to a second thickness that is less than the first thickness.

Whalen, Scott A.↗

Cladding and Butt-Joining Dissimilar Aluminum Alloys Simultaneously via Shear Assisted Processing and Extrusion

Shear assisted processing and extrusion has been used to fabricate multi-metallic tubing that incorporates regions with clad and butt-joined structures. In this work, aluminum alloys 6061, 7075, and 1100 are combined to create a monolithic extruded tubing with weldable ends (6061), a high strength center (7075), and a corrosion-resistant cladding (1100). Optical microscopy shows a gradual, defect-free, transition between alloys at the butt-joint interfaces and a sharp transition between alloys at the clad interface. Tensile testing proved the mechanical coherency of the joint, with failure occurring outside the tri-metallic structure. In conclusion, smoothed particle hydrodynamic simulations identified a spiral pattern of the cladding alloy that leads to inconsistent cladding thickness, and identified a simplified 2-alloy combination of aluminum alloys 6082 and 2014 that accomplished the design objectives of the tri-metallic structure.

Coatings↗

Solid Phase Processing of Mg-Al-Mn-Ca for High Strength and Ductility

While rare-earth Mg alloys have remarkable properties for high strength applications, lower cost alternatives are necessary for the widespread industry use of Mg. Ca added Mg alloys have shown promise as an alternative to rare-earth alloys. Ca-based precipitates can reduce basal texture, reduce casting porosity, and increase mechanical strength. However, the accumulation of Ca-based precipitates along inter-dendritic regions can severely limit ductility. Here, we apply two solid phase processing techniques, friction stir processing and shear assisted processing and extrusion, to produce wrought microstructure sheet and extruded tubes from a cast Mg-Al-Mn-Ca alloy. Ductility of the alloy is enhanced by densification under applied force and elevated temperature, grain refinement, and refinement of (Al,Mg)-Ca based precipitate.

Garcia, David↗

Materials Scorecards, Phase 2: Advanced Materials and Manufacturing Technology

This report presents updated material score cards with detailed justification of the proposed rating provided and quantifies the readiness of the advanced manufacturing of materials for nuclear applications. Based on an expanded literature review of available data, the scores in this report (Phase 2) have either been modified or remained constant as compared with Phase 1 scoring. The rating justification are provided for each scoring criteria whereas the maturity quantification of additively manufactured alloys and the knowledge gaps are discussed with reference traceability. This report focuses on the detailed justification and traceability for the adoption of additively manufactured 316SS, SS304, Alloy 800H, Graphite C/C, Alloy N, Silicon Carbide, HT9, Alloy 617, and Alloy 718. Significant variability in data and knowledge gaps exist among the identified materials. The scorecards are therefore based on published literature data, industry response to a survey, stakeholder input collected at workshops, and expert opinion. The interpretation and assessment were somewhat challenged as experimental process parameters and methodology varied and best judgment was exercised for score quantification. This assessment reflects the overall level of technical maturity for AM materials and their deployment in Gen-VI nuclear systems. These Phase 2 scorecards are likely to be revised based on additional input from stakeholders and as new research results become available.

36 MATERIALS SCIENCE↗

Co-extrusion of dissimilar Al alloys via shear assisted processing and extrusion

Cladded tubes are generally used where two distinct properties are required at the outer and inner part of a tube, for instance, strength and corrosion resistance. In this investigation, shear assisted processing and extrusion (ShAPE) was employed to fabricate bi-metallic tubes from 1100 and 7075, and 1100 and 2024 dissimilar Al alloy combinations. Surface defect-free bi-metallic tubes were fabricated via the ShAPE process. Detailed microstructural characterization of the interface and various locations of the cladded tubes were carried out using light and scanning electron microscopy techniques. A defect-free, metallurgically bonded interface between the cladded layer and high strength Al (7075 and 2024 Al) was observed. Furthermore, hardness and tensile properties of the cladded ShAPE tubes were examined in the as-extruded conditions.

Komarasamy, Mageshwari↗

Porosity evolution during heating of copper made from powder by friction extrusion

Here, friction extrusion was used to compact and extrude solid copper rod from feedstock powders. Following extrusion, considerable porosity was observed throughout the extrudate cross section due to the entrained porosity in the feedstock material and the extrusion process. The thermal stability of the extrudate was investigated via a series of heat treatments. Porosity evolution exhibited three distinct stages—an unchanged plateau (0°C–300°C) followed by an abrupt increase (400°C–500°C) and ultimately a reduction, as the temperature increases (>500°C). The peak porosity measured was ~25%. The underlying driving force for pore evolution is described as the competition between the internal pore pressure, material strength, and sintering kinetics, as a function of temperature. The observed porosity evolution and driving force are not expected to be limited to copper. Thus, this manuscript reveals an important consideration regarding elevated-temperature thermal stability as advanced manufacturing methods involving direct powder extrusion are explored.

36 MATERIALS SCIENCE↗

Exploring the Microstructure-Property Relationship of Mg-Al-Mn alloys enhanced via Friction Stir Processing

Friction Stir Processing (FSP) is a solid-state thermomechanical processing technique that enables local grain refinement, densification, and homogenization of microstructure in metallic components. Here, FSP is applied to thin sheets of high-pressure die cast AM60 to address the porosity and heterogeneities inherent to the casting process. In this work, microstructure characterization is correlated to improvements in the static mechanical properties of the Mg-Al-Mn alloy system at various FSP processing conditions. Notably, there is a significant increase in the ductility and ultimate tensile stress of system following FSP. The dominant deformation mechanisms for the as-cast material and the FSP material are investigated. Finally, the fatigue life improvement is correlated to microstructure modifications that may lead to distinct behavior in crack initiation and crack propagation for the as-cast and FSP material.

Garcia, David↗

Discovering SPP Thermomechanical Pathways

Final report for SPPSi project in Thrust One Friction extrusion is a thermomechanical process that combines conventional extrusion with the action of a rotating die. The plastic deformation of the material being sheared and extruded is the primary source of process heat and it produces strain distributions unlike those resulting from conventional extrusion. This paper proposes an improved strain analysis that evaluates three main strain components in a series of rate-controlled friction extrusions in which the steady state was achieved. Cylindrical AA1100 extrusion billets with two embedded markers were extruded to wire with a 10:1 diametral reduction. The shape change of the embedded markers was determined via serial, transverse sectioning and quantitative metallography of the extruded wires. Three mutually orthogonal strain components (longitudinal, circumferential, and radial) were calculated at different positions along each extruded wire from the marker's shape change. The development of strain from the initial transient to the steady state is discussed. The variation of the steady-state strain with different process parameters is correlated with the die advance per revolution.

42 ENGINEERING↗