TATB Thermal Decomposition: An Improved Kinetic Model for Explosive Safety Analysis
Explore the source record for details and available documents.
Engineering topics
Publications and source records attributed to Koroglu, Batikan.
Explore the source record for details and available documents.
Here, we synthesized uranium oxide nanoparticles using a plasma flow reactor (PFR) and studied the effects of three different experimental parameters on the resulting morphologies and speciation of the particles: (1) collection duration, (2) collection substrate temperature, and (3) radial collection position due to radial temperature gradients in the PFR. We also induced three distinct temperature histories along the axis of the plasma flow reactor by varying the gas flow rates downstream of the plasma torch. Transmission electron microscopy (TEM) analyses of collected particles showed two phases of uranium oxides (fcc-UO 2 and α-UO 3 ). The chemical compositions of the resulting uranium oxide particles were not altered by the three parameters investigated in this work but varied based on the temperature history induced. Preheating of the collection substrate led to deposition of fewer particles, which is attributed to a reduction in thermophoretic force caused by the reduced temperature gradient for preheated substrates. The relative amounts of UO 2 to UO 3 and particle size varied depending on the cooling history employed during synthesis.
In the process of multi-pulse laser ablation, inter-pulse delay time, Δ t , is known to be an important parameter for maximizing ablation efficiency as well as impulse imparted to the target. In this work, using photon Doppler velocimetry, we show that for single pairs of colinear pulses (1064 nm, 8 ns, ∼ 60 J cm -2 per pulse) in air, the peak free surface velocity of the back surface of an aluminum target (125 µm thick) is increased, by a factor of nearly 3, when Δ t = 10 microseconds, compared with both pulses arriving simultaneously (Δ t = 0). Fast imaging of the ablation process suggests this enhancement is due to rarefaction of the contiguous air in the passage of the leading shock produced by ablation, which then in turn allows a larger fraction of the energy of the second pulse to reach the target surface. This interpretation is strengthened by additional experiments in which the two pulses do not overlap on the target surface, but the shock strength is nevertheless enhanced. Given a fixed energy budget this work suggests a prescription for maximizing laser-driven shock strength by judicious choice of inter-pulse delay.
Not Available
Understanding the molecular composition of high explosives during thermal decomposition is vital for predicting the sensitivity, safety, and performance of explosive materials. The thermal decomposition of 1,3,5-triamino-2,4,6-trinitrobenzene (TATB) has been linked to the formation of furazans through a series of dehydration reactions of the NO2 and NH2 groups on the phenyl ring, along with breakdown into small molecules (≤120 amu). Molecular identification of compounds formed in this transformation of the furazans to light gases has been lacking. To address this, we have applied a pseudo-confined sampling system in a cryo-focused pyrolysis gas chromatography-mass spectrometry (pyGC-MS) system to molecularly identify these intermediates. By design, sublimation of TATB, which has complicated MS analyses of thermal degradation, was significantly reduced and additional compounds were identified with potential structural information. In addition to the known furazan compounds, one of these compounds forms from the loss of oxygen from benzo-trifurazan (F3) and produces an open ring structure that may be the first step in the formation of lower molecular weight furazan breakdown products. The loss of a nitro group from benzo-monofurazan (F1) was also discovered and implicates the formation of oxidizing NO2 gas in the thermal decomposition mechanism. So these findings are vital for understanding the proper heat flow from energetic materials on a molecular level, necessary when measuring enthalpy and developing decomposition models based on kinetic parameters.
The transport of radioactive material following a nuclear event depends heavily on fallout characteristics (e.g., composition, shape, and size), which in turn are controlled by the conditions under which the fallout forms. To this end, we use a novel plasma flow reactor (PFR) to explore how conditions including temperature history and gas mixing influence the chemical speciation and physical characteristics of uranium oxide nanoparticles. The PFR consists of a glass tube attached to an inductively coupled plasma (ICP) torch via an adaptor piece (ring flow injector) located downstream of the plasma-generating RF coil. We increase the gas flow rates from normal ICP operating conditions to higher values both upstream at the RF coil and downstream at the ring flow injector to create four distinct temperature profiles and two distinct gas flow mixing conditions (normal and higher Ar atomic ratios). Ex situ transmission electron microscopy (TEM) analysis is used to determine the crystal structure, morphology, and size distribution of the synthesized particles as a function of temperature and mixing. The particles display a striking dependence on these conditions in terms of the resulting speciation of uranium oxide: lower temperature (higher upstream) and slower cooling (normal downstream with normal Ar atomic ratio mixing) favor the formation of α-UO 3 particles, while faster cooling (higher downstream with higher Ar atomic ratio mixing) and higher temperature (normal upstream) favor the formation of UO 2 particles. The extent of gas mixing dictates particle aggregation: better mixing encourages the particles to aggregate more extensively. Here these results demonstrate the sensitivity of uranium to initial local conditions and can be used to improve our understanding of the kinetics that drive uranium speciation and ultimately inform fallout transport models.
Abstract Understanding the thermal decomposition behavior of TATB (1,3,5-triamino-2,4,6-trinitrobenzene) is a major focus in energetic materials research because of safety issues. Previous research and modelling efforts have suggested benzo-monofurazan condensation producing H 2 O is the initiating decomposition step. However, early evolving CO 2 (m/z 44) along with H 2 O (m/z 18) evolution have been observed by mass spectrometric monitoring of head-space gases in both constant heating rate and isothermal decomposition studies. The source of the CO 2 has not been explained, until now. With the recent successful synthesis of 13 C 6 -TATB ( 13 C incorporated into the benzene ring), the same experiments have been used to show the source of the CO 2 is the early breakdown of the TATB ring, not adventitious C from impurities and/or adsorbed CO 2 . A shift in mass m/z 44 (CO 2 ) to m/z 45 is observed throughout the decomposition process indicating the isotopically labeled 13 C ring breakdown occurs at the onset of thermal decomposition along with furazan formation. Partially labeled (N 18 O 2 ) 3 -TATB confirms at least some of the oxygen comes from the nitro-groups. This finding has a significant bearing on decomposition computational models for prediction of energy release and deflagration to detonation transitions, with respect to conditions which currently do not recognize this oxidation step.
Synthesis and characterization of chemical analogues of TATB, where specific atoms in the structure have been isotopically substituted, are reported. 15 N, 2 H, and 18 O have replaced the naturally occurring isotope distributions in the amino and/or the nitro attendant sites and 13 C has replaced the carbon in the ring structure. A modified wet-amination method was used to produce the analogues, and the isotopic replacements were performed by selective choice of labeled precursors. Four 15 N-labeled compounds (N replaced in the amino and nitro positions), two deuterium-labeled compounds (hydrogens replaced on the amino groups), and one 13 C-labeled compound (C in the ring substituted) were synthesized of high isotopic and chemical purity. One partially labeled 18 O-labeled compound (O in the nitro position) was a result of incomplete labeling due to exchange reactions during synthesis. The compounds were characterized by various spectroscopic methods – mass spectrometry (MS), solid-state nuclear magnetic resonance (SS-NMR), infrared (FTIR), powder x-ray diffraction (PXRD), and differential scanning calorimetry (DSC), depending upon the substitution. In conclusion, these compounds have been critical to the efforts in understanding the decomposition pathways of TATB when exposed to abnormal thermal environments.
This experimental study investigated the effects of confinement, starting mass, and heating rate on TATB thermal decomposition and sublimation using a combined Thermo-Gravimetric Analyzer and Differential Scanning Calorimetry (TGA/DSC) instrument. The confinement of volatile products was varied using different pinhole sizes with TGA/DSC pans. The measurements showed the open pan experiments without lids/pinholes resulted in complete sublimation of TATB between 320 °C and 360 °C. The heat of sublimation was determined to be 176 kJ/mol (42 kcal /mol), consistent with literature data obtained from other experimental techniques. The use of pinholes suppressed the sublimation of TATB such that the decrease in pinhole size resulted in 1) an increase in the enthalpy of reaction and an increase in the amount of carbonaceous material remaining at the end of decomposition, and 2) convergence of the two peak temperatures corresponding to maximum heat flow and maximum weight loss. Also, a transition from a two-exotherm thermal decomposition behavior towards a single-exotherm occurred as the pinhole size was decreased for a given starting mass or as the starting mass was increased for a given pinhole size. These results indicate the kinetics of TATB sublimation, TATB thermal decomposition, and gas diffusion out of a TGA/DSC pan can all compete and result in significantly different enthalpies, amounts of remaining materials, and peak temperatures depending on the pinhole size and starting mass used in the measurements. Furthermore, the results also indicate precise control of process variables (pinhole size, starting mass, and heating rate) in TGA/DSC measurements is required for thermal safety assessment of explosives.
Abstract In this work, a coupled Monte Carlo Genetic Algorithm (MCGA) approach is used to optimize a gas phase uranium oxide reaction mechanism based on plasma flow reactor (PFR) measurements. The PFR produces a steady Ar plasma containing U, O, H, and N species with high temperature regions (3000–5000 K) relevant to observing UO formation via optical emission spectroscopy. A global kinetic treatment is used to model the chemical evolution in the PFR and to produce synthetic emission signals for direct comparison with experiments. The parameter space of a uranium oxide reaction mechanism is then explored via Monte Carlo sampling using objective functions to quantify the model-experiment agreement. The Monte Carlo results are subsequently refined using a genetic algorithm to obtain an experimentally corroborated set of reaction pathways and rate coefficients. Out of 12 reaction channels targeted for optimization, four channels are found to be well constrained across all optimization runs while another three channels are constrained in select cases. The optimized channels highlight the importance of the OH radical in oxidizing uranium in the PFR. This study comprises a first step toward producing a comprehensive experimentally validated reaction mechanism for gas phase uranium molecular species formation.
Fallout analysis is a crucial field of study as it provides insight into the structural interactions that occur between radiological components and their surroundings following a nuclear event. Due to the complexity of actual fallout samples, setups like the plasma flow reactor (PFR) at LLNL have been developed to synthesize fallout in a controlled environment. While the PFR allows for control of parameters such as initial temperature, cooling rate, and concentration of radiological species, controlling the concentration of water has remained a challenge as samples are introduced into the setup via aqueous solution. To that end, our goal with this project was to develop methodologies to (1) monitor and (2) control the presence of water in the PFR. We found that a commercially available FTIR and MCT detector was sufficient to monitor the presence of both condensed and vapor-phase water, while a desolvating nebulizer could be used to control the amount of water injected into the system. In total, the results of this feasibility study have expanded the ability of the flow reactor to investigate key sensitivities that influence fallout formation.
Lawrence Livermore National Laboratory (“LLNL”) will outsource impact testing (also known as drop hammer testing) of PETN (Pentaerythritol tetranitrate) to Safety Management Services Inc. (“Subcontractor”). This document describes the objective, technical approach, and deliverables. Subcontractor will conduct impact testing studies on three PETN samples. LLNL will provide the samples. LLNL selected this company for impact testing because LLNL has an impact test machine purchased from the same vendor. The objective of this work is to answer the following questions: 1) What are the variations in impact sensitivity results between three PETN samples LLNL will provide?; 2) What is the effect of starting mass on impact sensitivity of PETN?
Local conditions, such as temperature and oxygen availability, have a pronounced effect on the formation and evolution of fallout following a nuclear explosion. While the behavior of nuclear-relevant materials such as uranium has begun to be explored under a wider range of environments, little is known about the behavior of plutonium. Here, using cerium as a surrogate, we track the vapor-phase aggregation of cerium oxide nanoparticles created in a plasma flow reactor under conditions of controlled temperature at two different oxygen fugacities. In situ optical emission spectroscopy is used to measure the variations in the spectral intensity of atomic and molecular species with temperature and oxygen content. We find that the relative rate of gas-phase oxidation of cerium is highly dependent on both temperature and local redox conditions within the flow reactor, to the extent that doubling the oxygen availability effectively doubles the amount of vapor-phase cerium monoxide at high temperatures (>2000 K). Condensed cerium oxide nanoparticles are also collected and analyzed ex situ via transmission electron microscopy and grazing-incidence small-angle X-ray scattering to determine their elemental composition, crystal structure, and size distribution. The size and morphology of the condensed nanoparticles are independent of local redox conditions, forming the same crystal type with the same size distribution regardless of oxygen availability. Postcondensation particle evolution, however, is found to be predominantly driven by temperature, with the average particle size increasing as particles cool and subsequently aggregate. These results expand our understanding of the chemical and physical behavior of refractory oxides that form during the early stages of fallout formation.
Abstract In order to model the fate and transport of particles following a nuclear explosion, there must first be an understanding of individual physical and chemical processes that affect particle formation. One interaction pertinent to fireball chemistry and resultant debris formation is that between uranium and oxygen. In this study, we use laser ablation of uranium metal in different concentrations of oxygen gas, either 16 O 2 or 18 O 2 , to determine the influence of oxygen on rapidly cooling uranium. Analysis of recovered particulates using infrared absorption and Raman spectroscopies indicate that the micrometer-sized particulates are predominantly amorphous UO x (am-UO x , where 3 ≤ x ≤ 4) and UO 2 after ablation in 1 atm of pure O 2 and a 1% O 2 /Ar mixture, respectively. Energy dispersive X-ray spectroscopy (EDS) of particulates formed in pure O 2 suggest an O/U ratio of ~ 3.7, consistent with the vibrational spectroscopy analysis. Both am-UO x and UO 2 particulates convert to α-U 3 O 8 when heated. Lastly, experiments performed in 18 O 2 environments show the formation of 18 O-substituted uranium oxides; vibrational frequencies for am-U 18 O x are reported for the first time. When compared to literature, this work shows that cooling timescales can affect the structural composition of uranium oxides (i.e., crystalline vs. amorphous). This indicator can be used in current models of nuclear explosions to improve our predicative capabilities of chemical speciation.
Alternative cements and production routes are necessary to offset the considerable global CO 2 emissions of Portland cement production. The combination of alkali-activation and mechanochemical milling in a CO 2 rich atmosphere is a promising green direction for synthesizing cementitious material as it upcycles hazardous material (slag) while capturing wt% of CO 2 during synthesis. We investigate the resulting structural transformations incurred during synthesis and hydration using a suite of characterization techniques including solid-state 27 Al, 29 Si, and 13 C NMR. The local aluminosilicate network structure of the processed clinker is best described by a melilite-type structure. Upon hydration, the network polymerizes to form a calcium, sodium aluminosilicate hydrate gel. The synthesis route also creates various metastable carbonates and bicarbonates from captured CO 2 and alkali-additives that transform into stable carbonate phases like calcite, aragonite, and gaylussite, after hydration. These findings indicate accelerated carbonation reactions occur during clinker production and demonstrates novelty as a green cement technology.
Fundamental observations of particle size distributions are needed to develop models that predict the fate and transport of radioactive materials in the atmosphere following a nuclear incident. The extent of material transport is influenced by the time scales of particle formation processes (e.g., condensation, coagulation). In this study, we investigated the influence of cooling time scales on size distributions of uranium, aluminum, and iron oxide particles that are synthesized separately under identical run conditions inside the controlled environment of an argon plasma flow reactor. Two distinct temperature distributions are imposed along the flow reactor by varying the argon flow rate downstream of the plasma torch. The vaporized reactants of uranium, aluminum, and iron are cooled from about 5000K to 1000K before they are collected on silicon wafers for ex situ scanning electron microscope analysis. The microscope images show that the sizes of the largest aluminum and iron oxide particles heavily depend on the cooling time scales, whereas significant size variation with cooling rate is not observed for uranium oxide particles. In addition, the size distribution of aluminum oxide particles exhibits the broadest range among all three metal oxides studied. We performed simulations of particle size distributions using a kinetic model that couples gas phase oxidation chemistry with particle formation processes, including nucleation, condensation, and coagulation. The model results demonstrate the strong sensitivity of particle size distribution to different cooling histories (i.e., temperature vs residence time) along the flow reactor. In conclusion, the kinetic model also helps identify directions for future research to improve the predictions.
We report that studies related to U gas-phase oxidation through plasma- and thermo-chemistry are important for many fields, including environmental monitoring, forensic analysis, debris analysis in a weapon detonation event, and nucleation physics. Recently, significant efforts have been made to understand the chemical pathways involved in the progression from U atoms to diatoms (UO) and polyatomic molecules (UxOy), employing optical spectroscopy tools and computational modeling. In many studies, laser ablation of U or a U-containing flow reactor are used as a highly resource-efficient, repeatable, tunable, and lab-scale testbed for studying gas-phase oxidation in U plasmas. The spectroscopic analysis of high-temperature gas-phase oxidation of U is challenging due to the congested U spectra, resolution limitations of instrumentation, and the numerous chemical reaction pathways possible. This article focuses on the current understanding and challenges related to studying U plasma chemistry, specifically U gas-phase oxidation and molecular formation, via optical spectroscopy of plasmas and associated computational and spectral modeling. The physical and chemical processes involved in the evolution from U atoms to U oxide molecules to nanoparticles and agglomerates (i.e., debris) are discussed in the context of optical spectroscopic studies. The article concludes by highlighting opportunities for future research efforts based on existing knowledge published in the literature.
Real-time measurements of the product gases arising from the thermal decomposition of triamino-trinitro benzene (TATB), its deuterated analogue, and plastically bonded TATB (LX-17) are presented in this study. Gas-phase decomposition products are identified by IR absorption spectroscopy. The frequency shifts in rovibrational spectra due to isotopic substitution and the change in rate of formation of decomposition products due to the kinetic-isotope-effect (KIE) help elucidate the decomposition pathways. The formation of H 2 O precedes other molecules (e.g., HCN, HNCO) during decomposition. After the concentrations of HCN and HNCO molecules reach a peak, their amounts gradually decrease. The concentrations of the other decomposition products (e.g., NH 3 and CO 2 ) rapidly rise after an induction period, which is attributed to the presence of autocatalytic reactions. The trends of chemical evolution are similar for all the samples, but their kinetic behaviors are different. This indicates the rates of consistent pathways are changed during thermal decomposition. Additionally, the kinetics of deuterated TATB decomposition is slower than that of unsubstituted TATB due to the KIE (kH/kD~1.41). The rate of LX-17 decomposition is slightly lower than unsubstituted TATB (k TATB /k LX-17 ~1.15). The KIE is more pronounced during the early stage of decomposition, which is attributed to the first steps of TATB decomposition involving water formation (i.e., H vs D transfer). The KIE slows down the formation of all gases, including those lacking hydrogen (e.g., CO 2 ). These results suggest the TATB thermal decomposition mechanism might involve a series of pathways rather than a set of independent and parallel reactions.