Search NASA⌕ Search

Engineering topics

Koskelo, Aaron C.

Publications and source records attributed to Koskelo, Aaron C..

Weak shock compaction on granular salt

This study conducted integrated experiments and computational modeling to investigate the speeds of a developing shock within granular salt and analyzed the effect of various impact velocities up to 245 m/s. Experiments were conducted on table salt utilizing a novel setup with a considerable bore length for the sample, enabling visualization of a moving shock wave. Experimental analysis using particle image velocimetry enabled the characterization of shock velocity and particle velocity histories. Mesoscale simulations further enabled advanced analysis of the shock wave’s substructure. In simulations, the shock front’s precursor was shown to have a heterogeneous nature, which is usually modeled as uniform in continuum analyses. The presence of force chains results in a spread out of the shock precursor over a greater ramp distance. With increasing impact velocity, the shock front thickness reduces, and the precursor of the shock front becomes less heterogeneous. Furthermore, mesoscale modeling suggests the formation of force chains behind the shock front, even under the conditions of weak shock. This study presents novel mesoscale simulation results on salt corroborated with data from experiments, thereby characterizing the compaction front speeds in the weak shock regime.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Jets from shocked metal surfaces with grooves: Missing experiments

Many studies have investigated the mass outflows generated when a planar shock transits an imperfect (“defected”) metal surface, where the defects are symmetric triangular or sinusoidal grooves. Yet a fundamental question remains unanswered: how does the quantity of outflow mass and its maximum velocity vary as a function of the groove cross-sectional aspect ratio? We identify two sets of missing experiments that must be addressed to answer the question. The aspect ratio (groove depth over width) is equivalently represented by θ, the cross-sectional half angle, or by η 0 k, the amplitude multiplied by an effective wavenumber. Low θ (high η 0 k) grooves comprise the first set of missing experiments, which are necessary to determine the validity of theoretical predictions of the nonlinear regime (η 0 k ≥ 1, θ < 57.5°). The second set of missing experiments are those in which the volume of the groove (or equivalently, the axial cross-sectional area) has been held constant as θ or η 0 k are varied. Such experiments are necessary to independently measure the effects of variations in groove volume and groove aspect ratio on the resulting jets.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Jets from shocked metal surfaces with grooves: Missing experiments

Many studies have investigated the mass outflows generated when a planar shock transits an imperfect (“defected”) metal surface, where the defects are symmetric triangular or sinusoidal grooves. Yet a fundamental question remains unanswered: how does the quantity of outflow mass and its maximum velocity vary as a function of the groove cross-sectional aspect ratio? We identify two sets of missing experiments that must be addressed to answer the question. The aspect ratio (groove depth over width) is equivalently represented by θ, the cross sectional half angle, or by η 0 k, the amplitude multiplied by an effective wavenumber. Low θ (high η 0 k) grooves comprise the first set of missing experiments, which are necessary to determine the validity of theoretical predictions of the nonlinear regime (η 0 k ≥ 1, θ < 57.5°). The second set of missing experiments are those in which the volume of the groove (or equivalently, the axial cross-sectional area) has been held constant as θ or η 0 k are varied. Such experiments are necessary to independently measure the effects of variations in groove volume and groove aspect ratio on the resulting jets.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

A mathematical framework for ejecta cloud dynamics with application to source models and piezoelectric mass measurements

We present a mathematical framework for describing the dynamical evolution of an ejecta cloud generated by a generic ejecta source model. We consider a piezoelectric sensor fielded in the path of an ejecta cloud, for experimental configurations in which the ejecta are created at a singly shocked planar surface and fly ballistically through vacuum to the stationary sensor. To do so, we introduce the concept of a time- and velocity-dependent ejecta “areal mass function.” We derive expressions for the analytic (“true”) accumulated ejecta areal mass at the sensor and the measured (“inferred”) value obtained via the standard method for analyzing piezoelectric voltages. In this way, we derive an exact expression and upper bound for the error imposed upon a piezoelectric ejecta mass measurement (in a perfect system) by the assumption of instantaneous creation, which is commonly required for momentum diagnostic analyses. This error term is zero for truly instantaneous source models; otherwise, the standard piezoelectric analysis is guaranteed to overestimate the true mass. When combined with a piezoelectric dataset, this framework provides a unique solution for the ejecta particle velocity distribution, subject to the assumptions inherent in the data analysis. The framework also leads to strong boundary conditions that any ejecta source model must satisfy in order to be consistent with apparently global properties of piezoelectric measurements from a wide range of experiments. We demonstrate this methodology by applying it to the Richtmyer–Meshkov instability+self-similar velocity distribution ejecta source model currently under development at Los Alamos National Laboratory.

97 MATHEMATICS AND COMPUTING↗

Analytic solutions for Asay foil trajectories with implications for ejecta source models and mass measurements

We consider the trajectory of an Asay foil ejecta diagnostic for scenarios where ejecta are produced at a singly shocked planar surface and fly ballistically through a perfect vacuum to the sensor. We do so by building upon a previously established mathematical framework derived for the analytic study of stationary sensors. First, we derive the momentum conservation equation for the problem, in a form amenable to accelerating sensors, in terms of a generic ejecta source model. The result is an integrodifferential equation of motion for the foil trajectory. This equation yields an easily calculable closed-form implicit solution for the foil trajectory in instant-production scenarios. From there, we derive a boundary condition that particle velocity distributions must satisfy if their associated foil trajectories are to exhibit a smooth initial acceleration, as occurs in some experiments. This condition is identical to one derived previously from a consideration of piezoelectric voltage data obtained in similar experiments. We also compare techniques for inferring accumulated ejecta masses from foil trajectories, first by deriving the exact solution, and then by quantifying the error imposed by a frequently used approximate solution (both subject to the assumption of instantaneous ejecta production). Finally, we examine the common practice of presenting inferred cumulative ejecta masses as a function of implied ejecta velocity, establishing the conditions under which this methodology is most meaningful.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Verification and Validation of High Explosive Reactive Burn Models Implemented in LANL's EAP and LAP Code Base

Reactive burn models represent a significant leap in high explosive (HE) modeling capability. The first generation of engineering models of HE detonation are called programmed burn models and they are largely based on the distance between a prescribed detonation point and each zone in a simulation. There have been many advancements to programmed burn models over the years and when the assumptions upon which they are based are met, a properly tuned programmed burn model can be highly accurate but if any of their assumptions is not met, as is the case for corner turning or weakly initiated HE burn, they will give the wrong answer. Reactive burn models represent an entirely new way of modeling HE burn. They use the local conditions of a zone – e.g. temperature, pressure or density – as calculated by a hydrocode to determine if and when the zone is going to detonate and if so, how rapidly. This difference opens up an entirely new set of capabilities for HE modeling. It makes it possible to accurately and predictively model phenomena like the effect of confinement and the formation of dead zones. Reactive burn models have seen sustained development effort at LANL for at least the last decade but several recent developments make it timely to transition reactive burn models from a research topic to a production tool. The main goal of this milestone is to facilitate and accelerate the adoption of reactive burn as a commonly available modeling option, with recommendations on the resolution that will be required and uncertainties associated with their modeling choices. To achieve this, we have performed verification, validation, and uncertainty quantification (UQ) assessments of AWSD and SURF/SURFplus in xRage and FLAG on a variety of different problems.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Verification and Validation of High Explosive Reactive Burn Models Implemented in LANL's EAP and LAP Code Base (FY2020 L2 Milestone MRT 7129) [Slides]

Advanced reactive burn models enable phenomena to be modeled that aren’t possible with programmed burn. Programmed burn propagates a burn front at a prescribed speed from a prescribed initiation point. Reactive burn uses the hydro variables (pressure, temperature, etc.) to determine when, how rapidly, and to what extent a zone detonates. This enables a completely new set of problems to be simulated. Our goal in this milestone has been to improve the usability of reactive burn modes. Thus, the closure criteria are: 1. Perform code and solution verification of the reactive burn models using appropriate solutions and simplified HE setups. 2. Perform validation assessments using small-scale experiments. 3. Evaluate sensitivities and quantify uncertainties due to model form variations and mesh dependencies.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

FY2019 ASC Physics Validation report: A validation assessment of the xRAGE laser package in 1d using Michel2013

In this report we use standard V&V methodologies to assess the current implementation of the laser-package in xRAGE. Validation assessment of the laser package is currently limited to single-shell, laser-driven, direct-drive experiments from the Omega laser facility (see Michel et al.). Rigorous evaluation was conducted to quantify model accuracy, confidence, and acceptability.

42 ENGINEERING↗

Assessment of Model Confidence of a Laser Source Model in xRAGE Using Omega Direct-Drive Implosion Experiments

Los Alamos National Laboratory is interested in developing high-energy-density physics validation capabilities for its multiphysics code xRAGE. xRAGE was recently updated with the laser package Mazinisin to improve predictability. We assess the current implementation and coupling of the laser package via validation of laser-driven, direct-drive spherical capsule experiments from the Omega laser facility. Here, the ASME V&V 20-2009 standard is used to determine the model confidence of xRAGE, and considerations for high-energy-density physics are identified. With current modeling capabilities in xRAGE, the model confidence is overwhelmed by significant systematic errors from the experiment or model. Validation evidence suggests cross-beam energy transfer as a dominant source of the systematic error.

47 OTHER INSTRUMENTATION↗