Engineering topics
Publications and source records attributed to Kostyk, Chris.
AFRC (Armstrong Flight Research Center) has a long history, and a lot of lessons learned, in testing hypersonic structures. This poster describes hypersonic structures, how to test them, and the methods used to develop the testing.
The paper looks at the radiant heat exchange between some fairly primitive geometry components, and a few more complex, to understand the radiant energy distribution under a very common radiant lamp consisting of 6 quartz tube (tungsten element) heaters. This is looking at the basic physics of a common device used around the world for many decades. Other papers have looked at this same topic, but ours is looking at other topics we have not seen addressed in the literature (that explain why it is what it is, and other things affecting data interpretation).
Non-pyrolyzingcarbonaceous materials represent a class of candidate material for hypersonic vehicle components providing both structural and thermal protection system capabilities. Two problems relevant to this technology are presented. The first considers the one-dimensional ablation of a carbon material subject to convective heating. The second considers two-dimensional conduction in a rectangular block subject to radiative heating. Surface thermochemistry for both problems includes finite-rate surface kinetics at low temperatures, diffusion limited ablation at intermediate temperatures, and vaporization at high temperatures. The first problem requires the solution of both the steady-state thermal profile with respect to the ablating surface and the transient thermal history for a one-dimensional ablating planar slab with temperature-dependent material properties. The slab front face is convectively heated and also reradiates to a room temperature environment. The back face is adiabatic. The steady-state temperature profile and steady-state mass loss rate should be predicted. Time-dependent front and back face temperature, surface recession and recession rate along with the final temperature profile should be predicted for the time-dependent solution. The second problem requires the solution for the transient temperature history for an ablating, two-dimensional rectangular solid with anisotropic, temperature-dependent thermal properties. The front face is radiatively heated, convectively cooled, and also reradiates to a room temperature environment. The back face and sidewalls are adiabatic. The solution should include the following 9 items: final surface recession profile, time-dependent temperature history of both the front face and back face at both the centerline and sidewall, as well as the time-dependent surface recession and recession rate on the front face at both the centerline and sidewall. The results of the problems from all submitters will be collected, summarized, and presented at a later conference.
The harsh and complex hypersonic flight environment has driven design and analysis improvements for many years. One of the defining characteristics of hypersonic flight is the coupled, multi-disciplinary nature of the dominant physics. In an effect to examine some of the multi-disciplinary problems associated with hypersonic flight engineers at the NASA Dryden Flight Research Center developed a non-linear 6 degrees-of-freedom, full vehicle simulation that includes the necessary model capabilities: aerothermal heating, ablation, and thermal stress solutions. Development of the tool and results for some investigations will be presented. Requirements and improvements for future work will also be reviewed. The results of the work emphasize the need for a coupled, multi-disciplinary analysis to provide accurate
Results of aerothermal material response calculations for the 5th Ablation Workshop Ablation Test-Case Series 2.
The originally designed SOFIA aircraft configuration included a system to pre-cool the telescope cavity on the ground before flight, however, due to various factors in the history of the project that system was not installed. This lack of ground pre-cooling was thus the source of the concern over whether or not the imagers would be exposed to a potentially unsafe thermostructural environment when the telescope cavity door was opened at altitude. This concern was in addition to the already existing concern that the air temperature rate of change during flight (both at the same altitude as well as ascent or descent) could cause the imagers to be exposed to an unsafe thermostructural environment. Four optical components were identified as the components of concern - two of higher concern (one in each imager) and two of lower concern (one in each imager). The requirement was to perform transient, coupled thermostructural analyses to determine whether the stress would ever achieve unsafe levels in these components. The analysis effort began by analyzing one component, after which the analyses for the other components was deemed unnecessary.
This content is for a DFRC Center Overview Poster for the 2011 TFAWS (Thermal & Fluids Analysis Workshop). The LaRC personnel running it gave each center POC the template to fill out, and send back so their graphics personnel could use a center aerial photo (or two) and the content to generate the poster (that way each center has the same template, etc.).
Progress in the development of new thermal protection systems (TPS) is reported. New approaches use embedded lightweight, sensitive, fiber optic strain and temperature sensors within the TPS. Goals of the program are to develop and demonstrate a prototype TPS health monitoring system, develop a thermal-based damage detection algorithm, characterize limits of sensor/system performance, and develop ea methodology transferable to new designs of TPS health monitoring systems. Tasks completed during the project helped establish confidence in understanding of both test setup and the model and validated system/sensor performance in a simple TPS structure. Other progress included complete initial system testing, commencement of the algorithm development effort, generation of a damaged thermal response characteristics database, initial development of a test plan for integration testing of proven FBG sensors in simple TPS structure, and development of partnerships to apply the technology.