Search NASA⌕ Search

Engineering topics

Kovar, Desiderio

Publications and source records attributed to Kovar, Desiderio.

Micro-cold Spray Deposition of YSZ Films from Ultrafine Powders Using a Pressure Relief Channel Nozzle

Abstract The use of ultrafine powders in the micro-cold spray (MCS) process, also referred to as the aerosol deposition method, typically results in porous and/or poorly adhering films because the particles do not impact at a high enough velocity for sufficient plastic deformation and interparticle bonding to occur. Under typical operating conditions, particles < 100 nm accelerate to high velocities but then are slowed by the stagnant gas in the bow shock that forms just upstream of the substrate. Using larger particles reduces particle slowing, but large particles can cause erosion of the film at high impact velocity, decreasing deposition efficiency. In this study, a pressure relief channel nozzle using helium as a carrier gas is proposed such that high-velocity deposition of yttria-stabilized zirconia particles as small as 10 nm in diameter is possible. This is well below the size range of powders previously used for MCS. The proposed nozzle design increases impact velocities for 10, 20, and 50 nm particles by ~ 880, 560, and 160 m/s, respectively, when compared to a conventional nozzle. Experimental deposition of ultrafine 8YSZ powder shows that the pressure relief channel nozzle results in lower porosity and more uniform deposits, with a ∼ 186% increase in deposition efficiency.

Materials Science↗

Machine Learning Enabled Atomistic Study of the Micro-Cold Spray Process [Poster]

Micro-cold spray is typically conducted by impacting 200-2000 nm particles at velocities of ~500 m/s. Molecular dynamics simulations have been used to study micro cold spray, but the particles that can be simulated using conventional potentials are much smaller than those used experimentally. The viewgraphs taken from molecular dynamics simulations and shown below are cross-sections of a 50 nm Ta particle with a 3 nm oxide layer impacting at 500 m/s using a machine learning enabled DeePMD potential. Using more expensive reactive interatomic potentials, the previous largest particle size for a metal/oxide impact simulation was 12 nm.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Nanoparticle Impact 2023 Report

Micro-cold spray (MCS) is a thermal spray process that can be used to apply thick ceramic films (1-100 μm) using kinetic energy to consolidate aerosolized powders into a dense film. While this process is compatible with many substrates due to the low working temperatures, the fundamental mechanisms that enable MCS and shape the operational window are poorly understood.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

A strain density function to analyze particle size effects during high velocity impacts of yttria

Here, the impact behavior of a single yttria (Y 2 O 3 ) nanoparticle onto a Y 2 O 3 substrate is studied as a function of particle velocity (300–1200 m/s) and diameter (12–50 nm) using molecular dynamics simulations. To analyze the results, a strain density function is developed to provide both quantitative and qualitative information about the deformation mechanisms that contribute to the final state of the system. This function provides both clear evidence of shear localization and insight into the conditions for which localization occurs during the impact of Y 2 O 3 particles as they approach experimentally relevant sizes. Further analysis shows that localization and fragmentation only occur for Y 2 O 3 impacts with diameters of at least 50 nm, while particles with diameters of 25 nm and smaller deform primarily by amorphization and viscous flow. Implications for the deposition of films of Y 2 O 3 and other rare-earth oxides via the micro cold spray process are discussed.

36 MATERIALS SCIENCE↗

Effect of an oxide layer on high velocity impact of tantalum particles characterized using molecular dynamics

Micro-cold spray, also commonly referred to as the aerosol deposition method or vacuum kinetic spraying, is a process for depositing nanostructured films of metals and ceramics by impacting solid nanoparticles at high velocity onto a substrate at room temperature and at low pressures. Tantalum films deposited by micro-cold spray are desirable because tantalum is non-reactive to certain molten metals and can therefore serve as a non-reactive barrier coating. However, unlike most other metals deposited by micro-cold spray, tantalum quickly forms an oxide layer when exposed to air. In the deposition of films using traditional cold spray with much larger particles, native oxides must fracture for particle–substrate bonding to occur. Furthermore, the fraction of the particle that is oxidized in micro-cold spray and the strain rates experienced by the particles upon impact are both much larger than in cold spray, suggesting that the role of the oxide on film deposition may be distinct. The effect of this oxide layer on particle deformation and adherence to a substrate under high strain rates is studied using molecular dynamics simulations. The effect of oxide layer thickness, particle diameter, and impact velocity are examined.

42 ENGINEERING↗

The onset of selective laser flash sintering in undoped and doped lanthanum chromite

Previous studies have shown that selective laser flash sintering (SLFS) can be initiated in dielectrics that exhibit ionic or electronic conduction at high temperature. These materials required high laser powers to reach the temperatures where electrical conduction is sufficient to initiate SLFS. In this study, SLFS in lanthanum chromite (LC), an intrinsic electronic conductor with high conductivity, and lanthanum strontium chromite (LSC), which is doped to further increase electronic conductivity, were investigated with a focus on understanding the initiation mechanisms. Results show that the initiation of SLFS in LC and LSC occurs when electronic charge carriers are activated and flow to the electrode where the current is measured. A combination of carriers produced at the electrode, temperature-activated intrinsic charge carriers, and extrinsic charge carriers present in LSC due to doping are responsible for the facile initiation of SLFS.

36 MATERIALS SCIENCE↗

A molecular dynamics survey study of impact-induced amorphization in yttria nanoparticles

The impact of a single yttria (Y 2 O 3 ) nanoparticle onto a yttria substrate was studied as a function of particle velocity (300–1200 m/s) and diameter (5–12 nm) for three particle orientations and two substrate orientations using molecular dynamics simulations. Impacts resulted in minimal dislocation motion but extensive disordering of the crystal lattice without approaching the melting temperature. The resulting amorphous microstructure was both precisely coincident with plastic strain and retained until the end of the simulation, suggesting a deformation mechanism of amorphization-facilitated viscous flow. Further analysis revealed that the degree of amorphization depended primarily on the impact velocity and secondarily on the orientations of the particle and substrate, with significant second-order effects from variable interactions.

74 ATOMIC AND MOLECULAR PHYSICS↗

Onset of selective laser flash sintering of AlN

Abstract Flash sintering uses a combination of heating and electric fields to rapidly densify ceramics. Previously, it has been shown that a scanning laser can be used to initiate flash sintering in localized regions on an yttria‐stabilized zirconia (YSZ) sample in a process known as selective laser flash sintering (SLFS). In this work, we show using a combination of measurements of electric current flowing through the sample and observations of necks formed between powder particles that aluminum nitride (AlN) can also undergo SLFS. Scan conditions required to initiate SLFS are characterized over a range of laser powers and laser scan speeds in a dry nitrogen environment. It is shown that initiation of SLFS in AlN is governed by both the local input energy density per scan and heat dissipation and a numerical model is developed to predict temperatures during SLFS. Assuming the minimum temperature along the conductive path determines the onset of SLFS, the minimum temperature and time required is 450–670 K in 2–0.25 s for the pressed AlN pellets used in this study for laser scan speeds of 33–300 m/s, laser powers of 10–30 W, and an applied electric field of 3000 V/cm.

Gouws, Andre↗